m M₁ > > > > > ) "²" Select e: -1.0 kNm Two parts shaft of lengths I₁ = 2 m, L,- 1.6 m is loaded by two concentrated moments M₁ = 4 kNm, M₁ = = 2 kNm and the distributed moment of the intensity m = 1.5 kNm/m -2.2 kNm Define the torque in the cross-section of shaft z = 0 m. Note: The torque is accepte as positive, if looking at the shaft section plane from outside, the moment actoin can be seen in the counter-clockwise direction 1.3 kNm L₁ 2.2 kNm L₂ 1.0 kNm M₂ Z

m M₁ > > > > > ) "²" Select e: -1.0 kNm Two parts shaft of lengths I₁ = 2 m, L,- 1.6 m is loaded by two concentrated moments M₁ = 4 kNm, M₁ = = 2 kNm and the distributed moment of the intensity m = 1.5 kNm/m -2.2 kNm Define the torque in the cross-section of shaft z = 0 m. Note: The torque is accepte as positive, if looking at the shaft section plane from outside, the moment actoin can be seen in the counter-clockwise direction 1.3 kNm L₁ 2.2 kNm L₂ 1.0 kNm M₂ Z

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

A turbine rotor is mounted on a stepped shaft that is fixed at both ends as shown in The torsional stiffnesses of the two segments of the shaft are given by k = 3,000 N-m/rad and k2 = 4,000 N-m/rad. The turbine generates a harmonic torque given by M(1) = Mo cos wt about the shaft axis with M, = 200 N-m and w = 500 rad/s. The mass moment of inertia of the rotor about the shaft axis is J, = 0.05 kg-m?. Assuming the equivalent torsional damping constant of the system as e, = 2.5 N-m-s/rad, determine the steady-state response of the rotor, 0(1). O(1) M(1) = Mg cos etr %3! Turbine rotor, Jo
A turbine rotor is mounted on a stepped shaft that is fixed at both ends as shown in The torsional stiffnesses of the two segments of the shaft are given by ka = 3,000 N-m/rad and k2 = 4,000 N-m/rad. The turbine generates a harmonic torque given by M(t) = Mo cos wt about the shaft axis with M, = 200 N-m and w = 500 rads. The mass moment of inertia of the rotor about the shaft axis is Jo = 0.05 kg-m. Assuming the equivalent torsional damping constant of the system as c, = 2.5 N-m-s/rad, determine the steady-state response of the rotor, 6(1). O(1) ke M(1) = M, cos ot Turbine rotor, Jo
A turbine rotor is mounted on a stepped shaft that is fixed at both ends as shown in The torsional stiffnesses of the two segments of the shaft are given by k = 3.000 N-m/rad and k2 = 4,000 N-m/rad. The turbine generates a hamonic torque given by M(1) = Mo cos ot about the shaft axis with Mg = 200 N-m and as = 500 rad/s. The mass moment of inertia of the rotor about the shaft axis is h = 0.05 kg-m. Assuming the equivalent tosional damping constant of the system as e, = 2.5 N-m-s/rad, determine the steady-state response of the rotor, 6(1). ka M() = Ma cos e Turbine rotor, Jo A 50-kg turbine is mounted on four parallel springs, each of stiffness of 3 x 10° N/m When the machine operates at 40 Hz. its steady-state amplitude is observed as 1.8 mm What is the magnitude of the excitation? Given m = 50 kg. k = 3x 10 Nm. e = 40 Hz. X= 1.8 mm Find: Fe
8:30 Test 3.pdf F1 F2 a CF3 A b a F4 D Consider the following values: - F5 a = 12 m; b = 10 m; c = 10 m; d = 8 m; F1 = 6 kN; F2 = 7 kN; F3 = 8 kN; F4 = 9 kN; F5 = 10 kN; a = 30°, 0= 45° , B = 60° 1] What is the resultant moment of the five forces acting on the rod about point A? a) - 111.6 kN.m b) 112.6 kN.m e) - 184.6 kN.m d) - 109.6 kN.m e) - 104.1 kN.m 0 None of them 21 What is the resultant moment of the five forces acting on the rod about point B? a) -95.8 KN.m b) 42.7 kN.m c) 80.9 kN.m d) 10.9 kN.m e) 51.8 kN.m ) None of them 31 What is the resultant moment of the five forces acting on the rod about point C? b) - 21.1 kN.m e) 17.4 kN.m d) - 16.5 kN.m e) 15.6 kN.m ) None of them a) 32.6 kN.m 4] What is the resultant moment of the five forces acting on the rod about point D? a) 37.6 kN.m b) 73.8 kN.m c) 71.6 kN.m d) 52.1 kN.m e) 21.1 kN.m ) None of them 5] What is the moment of the force F2 about point E? a) 90.7 kN.m b) - 88.1 kN.m c) 54.6 kN.m d) 103.1 kN.m e) 100.7 kN.m ) None…
d 6- Two shafts 'A' and transmit the same power. The speed of shaft 'A' is 250 r.p.m. and that of shaft is 300 r.p.m. The shaft 'B' has the greater diameter The shaft 'A' has the greater diameter None of these Both are of same diameter d- 7- In the torsion equation T/=T/r= GB/L, the term //R is called Shear modulus b- Section modulus Polar modulus d- None of these
The figure below shows a shaft of three segments. It is restrained (fixed support) at both sides and is loaded by two torques. Use Gpronze = 35 GPa, Galum = 28 GPa, and Gsteel = 83 GPa. Bronze Aluminum Steel diameter = 25 mm diameter = 50 mm diameter = 25 mm T-300 N.m- K To-700 N.m K D B 2 m - 2 m - 2.5 m Determine the angle of twist developed in steel from support B. Select the correct response: O 0.005 rad 0.516 rad 0413 rad 0.511 rad 日E周 TETET
YA 37 N-m The braket shown in figure is subjected to three forces and one couple as Shown in figure. Find the result ant R of the force System and the of it's line of action with the lines AB and BC. 120N 600N 9. 30 200 mm 50 mm V1OON points of intersedion R = 446.86 NoO =26:58s %3D d=0.0447m =44.7 mm « a = 0. ol m = lomm 6 %3D b=0.05 m = 50 mm · loomm
т M1 M2 L1 L2 Two parts shaft of lengths L, = 2.5 m, L,=2.0 mis loaded by two concentrated moments M, = 5 kNm, M,=6 kNm and the distributed moment of the intensity m = 2 kNm/m Define the torque in the cross-section of shaft z = 3 m. Note: The torque is accepte as positive, if looking at the shaft section plane from outside , the moment actoin can be seen in the counter-clockwise direction
:Q81 The moment M for the force the figure shown below is 250 N 153 -200 mm 30 mm 46.5 N.M O 46.6 N.M O 46.4N. M of L is
The dimensions of a stepped shaft are shown below. The maximum shear stress specification of the material is 67.1 MPa. Calculate the allowable torque for the shaft. r= 2.4 mm 12 mm 15 mm
Micro Bh Micros Bb Micros - с * Question Completion Status: Question 2 2.0 d=1.50 in. dia. 1.9 1.8 Class r = 0.08 in. The figure below show a stepped shaft in torsion. Compute the maximum shear stress at the step when it rotates at 100 rad/s and transmits 5000 lb-in/s. Use CamScanner app or Notes app of iPhone to scan all hand-written pages into one PDF file. Attach the PDF file here to answer in this question. Class ( bbhosted.cuny.edu/webapps/assessment/take/take.jsp?course_assessment_id=_2374 Class D = 2.00 in. dia. r= Fillet radius Class G Cuent Projec suntur Et WA AS hp
A shaft required to transmit 50kW of power will be running at 100rev/min. The maximum twist in 3m length of the shaft is limited to 1.5 degree. If the maximum torque is 30 percent more than mean or average torque. Assume entirely elastic action and take modulus of rigidity for the shaft material G = 135 GN/?2. Determine the following:a. Diameter of the shaft.b. Maximum shear stress developed in the shaft. I need answer ASAP. Thank you!