Problem (6): Rigid bar ABCD is supported by two vertical bars. There is no strain in he vertical bars before load P is applied. After load P is applied, the normal strain in par (1) is 0.0011m/m. Determine the normal strain in bar (2) in units of m/m. 2 (1) (2) 1.55 m 2.00 m A C D 1.75 m 2.45 m 1.75 m

Problem (6): Rigid bar ABCD is supported by two vertical bars. There is no strain in he vertical bars before load P is applied. After load P is applied, the normal strain in par (1) is 0.0011m/m. Determine the normal strain in bar (2) in units of m/m. 2 (1) (2) 1.55 m 2.00 m A C D 1.75 m 2.45 m 1.75 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the loadP = 20 KN is applied. Steel L=2m A=250mm 4m E=200Mpa C. Aluminum L=2m A=500mm2 2m 2m E-72Mра P=20KN
Determine the normal stress in the steel plate. Gusset plate is 16 mm thick column pin diameter = 20 mm gusset plate steel plate 70 kN pin 60mm 8-mm plate thickness 183.45 MP 0148.53 MPa 58.33 MP3 22282 MP A 14583MP
Two plate are joint by five rivets of 20 mm diameter. What is the shear stress in the material if the shear forces is 18840 N O 12 N/mm2 O 20 N/mm2 O 15 N/mm2
Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum tensile bending stress will occur at point C. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner C does not exceed 205 MPa. Answer: M- eTextbook and Media Save for Later Part 3 8.31E1 Answer: M-i The z-component of moment M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum compressive bending stress will occur at point A. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner A does not exceed 205 MPa. eTextbook and Media Save for Later Part 4 kN-m * Your answer is incorrect. kN-m Submit Answer Determine the maximum bending moment that can be applied to this cross…
Situation 2 For the assembly shown, determine the stress in each of the two vertical rods if the temperature rises 40°C after the load P=50 KN is applied. Neglect the deformation and the mass of the horizontal bar AB. Compute the vertical movement under the load. Steel Aluminum E=200 GPa E=70 GPa L-4m A=300 mm? a-11.7x10*/°C L-3m A=900 mm a=23x10“ /°C 3 m 3 m 3 m Situation 3
3. Two bars are made of a material with the stress-strain diagram as shown. Find the cross-sectional area of each bar so the bars fail at the same time with the load is P = 4 kips. Use a factor of safety of 1.8. 3 ft 4 ft P B σ (ksi) 25 20- 15 10- 5H 0 0 tension. compression 0.20 0.40 0.60 0.80 e (in./in.)
The light rigid bar ABCD shown below is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load P = 20 kN is applied. steel L=1.5 m A=300 mm2 2 m- E= 200 GPa B D Aluminun L=2 m P = 20 kN - 1m A= 500 mm2 E= 70 GPa
The light rigid bar ABCD shown below is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load P 20 kN is applied. steel L=1.5 m A=300 mm2 E= 200 GPa Ahuminun L=2 m A= 500 mm2 E= 70 GPa 1m1m- P = 20 kN 2.
Problem 1: The steel rod is placed inside the copper tube, the length of each being ex-, actly 15 in. If the assembly is compressed by 0.0075 in., determine the stress in each component and the applied force P. The moduli of elasticity are 29 × 106 psi for steel and 17 x 10° psi for copper. 0.6 in. 0,75 in. Problem 2: A steel hoop, 10 mm thick and 80 mm wide, with inside diameter 1500.0 mm, 15 in. is heated and shrunk onto a steel cylinder 1500.5 mm in diameter. What is the nor- mal force in the hoop after it has cooleď? Neglect the deformation of the cylinder, and use E == 200 GPa for steel. 0.125 in. Problem 3: The timber member has a cross-sectional area of 1750 mm² and its modulus of elasticity is 12 GPa. Compute the change in the total length of the member after the loads shown are applied. 40 kN 35 kN 20 kN D +1.5 m -3 m 3 m
3. The aluminum shaft, composed of three segments is fastened to rigid supports as A and D. Calculate the maximum shear stress in each segment when the two torques are applied. rigid support @ A A 400 N-m 850 N-m L=1.4 m 30 mm diameter B® L=2.4 m 50 mm diameter L=1.9 m 30 mm diameter rigid support @ D
CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the weight of the beam is 375 KN, determine the stress in the aluminum bar (in MPa). Bronze Bronze Alum Alum Bronze A in mm2 850 1500 E in Gpa 70 83 103.56 O 79.45 451.30 33.47
G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the load P 20 KN is applied. Steel L=2m A=250mm 4m E=200Mpa Aluminum L=2m A=500mm 2m 2m E-72Mра P=20KN