1. A steel bar of circular cross section with 20mm diameter is supported by three springs and loaded with 2 KN, as shown in figure. If Eatee 200 GN/m?, stiffness of springs (1, 2 and 3) are (300, 300 and 450) N/mm respectively. Using finite element method to estimate: • The force at land 6. • The stress distributions in the steel bar. 2 KN p20 wwww 300 200 All dimensions in mm

1. A steel bar of circular cross section with 20mm diameter is supported by three springs and loaded with 2 KN, as shown in figure. If Eatee 200 GN/m?, stiffness of springs (1, 2 and 3) are (300, 300 and 450) N/mm respectively. Using finite element method to estimate: • The force at land 6. • The stress distributions in the steel bar. 2 KN p20 wwww 300 200 All dimensions in mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An aluminum bar having a cross-sectional area of 160 mm² carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B, = 0.8 m; B2 = 1.0 m; B; = 0.6 m. Determine the axial stress of bar B3 in MPa. 35KN B1 B2 B3 10KN 15KN 30KN A) 218.75 в) 125 62.5 D 31.25
3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 13.05 ksi, or in bronze of 100 MРа. Aluminum A = 400 mm Bronze A = 200 mm Steel A = 500 mm? 2P 4P 2.5 m 2.0 m 1.5 m
Q2: The pin-connected structure shown in figure below consists of a rigid member BED and three steel rods (E= 200 GPa). Each of the rods AB and CD has a 200 mm? cross-sectional area and rod EF has a 625 mm? cross-sectional area. If a load of P= 36 kN is applied at E, determine: (a) the change in length of rod EF. (b) the stress in each rod. A 300 mm E P-36 kN 300 mm DIO 400 mm 500 mm
2)For the supporting frame shown below: a) Determine the internal forces acting at section a-a. b) Determine the stress components that act at points A and B. IN = 2.6525x10-7 mª -300 mm 150 mm 2.5 kN a 12 mm 6 mm 6 mm 6 mm 36 mm'36 mm Section a – a
Knowing that the couple shown acts in a vertical plane, determine the stress at (a) point A, (b) point B. (a) GA= (b) B = +201 B. 40 20 Dimensions in mm MPa MPa 20 80 20 T N M = 12 kN - m
An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B, = 0.8 m; B, = 1.0 m; B3= 0.6 m. Determine the axial stress of bar B; in MPa. 35KN B1 B2 ВЗ ... 10KN 15KN 30KN A 218.75 B 125 C 62.5 D 31.25
3. A rigid block of mass M is supported by three symmetrically spaced rods as shown in the figure. Each copper rod has an area of 900 mm²; E = 120 GPa; and the allowable stress is 70 MPa. The steel rod has an area of 1200 mm²; E = 200 GPa; and the allowable stress is 140 MPa. Determine the largest mass M which can be supported. Copper 160 mm M Steel 240 mm Copper 160 mm
A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its thickness is 7 mm. Consider that the yield strength of steel is 240 MPa. Analyze point H ONLY. Due to the pressure in the pipe, there is an 11.25-MPa (T) normal stress along x and a 22.50-MPa (T) normal stress along z of point H. A. Determine the internal forces and moments at the pertinent section through an FBD. B. Determine the stresses experienced by point H. Illustrate using a stress element. C. Determine the FS by MSST at point H D. Determine the von Mises equivalent stress at point H E. Determine the FS by MDET at point H 700 mm 16 KN 1,300 mm
A circular steel tube of length L = 1.5 m is loaded in torsion by torques T (see figure). T r2 (a) If the inner radius of the tube is r, = 41 mm and the measured angle of twist between the ends is 0.5°, what is the shear strain y, (in radians) at the inner surface? (Enter the magnitude.) rad (b) If the maximum allowable shear strain is 0.00026 rad and the angle of twist is to be kept at 0.45° by adjusting the torque T, what is the maximum permissible outer radius (r,)may (in mm)? mm Enter a number.
A hollow tube ABCDE constructed of Monel metal is subjected to five torques acting in the directions shown below. The tube has an outside diameter d, of 1.0 in. Given that the allowable shear stress is 12 kši, then the maximum permissible inside diameter d; of the tube is equal to T = 1000 lb-in. 800 lb-in. T = T3 = 500 Ib-in. 500 lb-in. T = T5 = 800 1b-in. B C E dz = 1.0 in. O 0.697 in O 0.908 in O 0.788 in O 0.618 in
An aluminum bar having a cross-sectional area of 160 mm carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1 = 0.8 m: B2 = 1.0 m; B3= 0.6 m. Determine the axial stress of bar B; in MPa. 35KN B1 B2 B3 ... 10KN 15KN 30KN A) 218.75 В 125 C 62.5 D) 31.25
An aluminum bar having a cross-sectional area of 160 mm² carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1= 0.8 m; B2= 1.0 m; B3= 0.6 m. Determine the axial stress of bar B3 in MPa. 35KN B1 B2 B3 10KN 15KN 30KN