The pumping system shown below consists of a suction pipe of length 3m and diameter80mm; delivery pipe of length 6m and diameter 80mm; 4 elbows, each with a losscoefficient of k = 0.3; total static lift = 6m; tank entry and exit loss coefficients 0.5 and 1.0,respectively; suction and delivery pipe friction factor f = 0.007 Darcy. A Robuschi 150-500pump rotates at 1470 rpm and the desired flow rate is a minimum of 200 m³/h.SUCTON EComplete the following tasks:1. Draw the system curve as described above on the Roubuschi pump curve datasheet supplied. Work in increments of Q 50m³/h starting at 0 (7-point curve)2. Would you advise the client to select the 400 or 460 impeller?Give two reasons for your answer.If the 6400 impeller is used:Assume:• the gauge pressure in the suction tank at 115 kPa,• the vapour pressure of the water at its average operating temperature at 20C• suction height as 1.5 m.3. Is the pump likely to cavitate? Support answer with a NPSH calculation approach.4. Describe two steps that could be taken to reduce the likelihood of cavitation. POMPAR150 · 5001470giri/minRPMGIRANTE: max/min - 499 / 400 mm - previsto Ø -Peso spec.- Vise.mmImp. gpm50010001500oUS. opm500100150020009아409:| 3003040506065707548080H460250ftm.704404201602006040050F1504030나10049946020 ft42040010-160200$ 499480460100 p440cvkW420100400200100Qm³/h300400500ROBUSCHJ"CLIENTEN 138061Ril.NPSH 3* HSDN

To given thatsuction pipe diameter,(d)=80mm=0.08mSuction pipe length=3mDelivery pipe…

e pumping system shown below consists of a suction pipe of length 3m and diar nm; delivery pipe of length 6m and diameter 80mm; 4 elbows, each with a fficient of k = 0.3; total static lift = 6m; tank entry and exit loss coefficients 0.5 ane pectively; suction and delivery pipe friction factor f = 0.007Darcy- A Robuschi 150 np rotates at 1470 rpm and the desired flow rate is a minimum of 200 m/h. SUCTION E mplete the following tasks: 1. Draw the system curve as described above on the Roubuschi pump curve sheet supplied. Work in increments of Q 50m/h starting at o (7-point curve) 2. Would you advise the client to select the 400 or 460 impeller? Give two reasons for your answer.

e pumping system shown below consists of a suction pipe of length 3m and diar nm; delivery pipe of length 6m and diameter 80mm; 4 elbows, each with a fficient of k = 0.3; total static lift = 6m; tank entry and exit loss coefficients 0.5 ane pectively; suction and delivery pipe friction factor f = 0.007Darcy- A Robuschi 150 np rotates at 1470 rpm and the desired flow rate is a minimum of 200 m/h. SUCTION E mplete the following tasks: 1. Draw the system curve as described above on the Roubuschi pump curve sheet supplied. Work in increments of Q 50m/h starting at o (7-point curve) 2. Would you advise the client to select the 400 or 460 impeller? Give two reasons for your answer.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Centimuity oquation ofastendy frow. Terriellis problemfontflow of liquid througha hole) Problem:Detemine the absolute pressure at the inlet section of the pump. Flow rate of the pump Q=2,3 1/sec, l=1,5 m, d=40 mm, t=60°C. Static pressure in the tank p.=266,8 mmHg. Wedge resistance coefficient Sw=1,5, pipe inlet resistance coefficient Çin=0,5, the height of the oil level in the tank above the pump inlet section н-1,2 м, оil 1-12. H кран насос
PUMP SYSTEM - SYSTEM CURVE AND NPSH SUBMIT BY 8 MAY 2022 The pumping system shown below consists of a suction pipe of length 3m and diameter 80mm; delivery pipe of length 6m and diameter 80mm; 4 elbows, each with a loss coefficient of k = 0.3; total static lift = 6m; tank entry and exit loss coefficients 0.5 and 1.0, respectively; suction and delivery pipe friction factor f = 0.007Daroy. A Robuschi 150-500 pump rotates at 1470 rpm and the desired flow rate is a minimum of 200 m/h. Complete the following tasks: 1. Draw the system curve as described above on the Roubuschi pump curve data sheet supplied. Work in increments of Q 50m³/h starting at 0 (7-point curve) 2. Would you advise the client to select the 400 or 460 impeller? Give two reasons for your answer. If the 400 impeller is used: Assume: the gauge pressure in the suction tank at 115 kPa, • the vapour pressure of the water at its average operating temperature at 20C • suction height as 1.5 m. 3. Is the pump likely to cavitate?…
Ex ....... HYDRAUE • The pump is to be connected to a rising main which has a diameter (D) of 400 mm and a length of 137 m.The entry exit and minor head losses in the pipeline can be taken as 80D in this particular situation. The friction loss can be approximated by h; = ALQ² / 1 2D5 with A=0.04. The static lift is 10 m. By considering a single pump (P). And two of the pumps in series (P+P) and parallel (P//P) determine: > the H-Q curve of the two pump combinations » Which combination will be capable of discharging at least 0.3 m³/s, with the ability to pump up to 0.35 m³/s if the need arises. %3D
A branch duct for a heating system measures 75 * 250 mm. Compute the circular equivalent diameter. Then determine the maximum flow rate of air that it could carry while limiting the friction loss to 0.80 Pa/m De=144 mm and Qmax=40 m3/s De=381 mm and Qmax=0.6 m3/s De=464 mm and Qmax=991 L/s De=117 mm and Qmax=45 L/s De=1390 mm and Qmax=17.5 m3/s
Using velocity reduction method, design the duct system. Take the velocity of air in main duct as 8m/sec, air density 1.2kg/m. Coranch = 0.4 Coutlet = 1 2. Using equal pressure drop method, design the duct system. Take Ap = 1pa/m, air density 1.2kg \m. Cranch = 0.4 Coutlet = 1
A local ventilation system (a hood and duct system) is used to remove air and contaminants from a pharmaceutical lab (Fig. 1). The inner diameter (ID) of the duct is 129 mm, its average roughness is 0.15 mm, and its total length is L = 24.5 m. There are three elbows along the duct, each with a minor loss coefficient of 0.21. Literature from the hood manufacturer lists the hood entry loss coefficient as 3.3 based on duct velocity. When the damper is fully open, its loss coefficient is 1.8. The minor loss coefficient through the 90° tee is 0.36. Finally, a one-way valve is installed to prevent contaminants from a second hood from flowing “backward” into the room. The minor loss coefficient of the (open) one-way valve is 6.6. The performance data of the fan fit a parabolic curve of the form Havailable = H0 - aV2, where shutoff head H0 = 60.0 mm of water column, coefficient a = 2.50 x 10-7 mm of water column per (Lpm)2 ,available head Havailable is in units of mm of water column, and…
Problem 2 - Pumps in Parallel Two 32-in pumps, with performance curve shown below, are combined in parallel to deliver water at 60°F through 1500 ft of horizontal pipe. If f = 0.025, what pipe diameter will ensure a flow rate of 35,000 gal/min for n = 1170 rev/min? 1170 r/min 800 50 NPSH 700 600 500 400 300 200 Total head, ft 0 36-in dia. 32-in dia. 28-in dia. 4 8 82% 85% 1500 bhp 87% 88% 3000 bhp, 3500 bhp 87% 2500 bhp 2000 bhp 12 16 20 24 U.S. gallons per minute x 1000 28 8 8 8 8 NPSH, ft 40 30 20
Q.2 A centrifugal pump is required to pump water to an open water tank situated 4 km away from the location of the pump through a pipe f diameter 0.2 m having Darcy's frřiction factor of 0.01. The average speed of waterinthe pipe is 2 m/s. If it is to maintain a constant heac of 5 m in the tank, neglecting other minor losses, the absolute discharge pressure at the pump exit is (a) 0.449 bar (c) 44.911 bar dund (b) 5.503 bar (d) 55.203 bar
Length and dia. Of pipe 1 are 2000m and 1m while the second pipe is 2000m and dia. Of 0.8m .Find the rate flow of each pipe if the total flow rate in the main pipe is 0.3 m3/s. the coefficient friction of each pipe is same and equal to 0.05. Ans.Q1= 1.906 m3/s , Q2=1.094m3/s Ex. A pipe of dia.=20cm and length 2000m is connects two reservoir having difference of water levels as 20m determine the discharge through pipe. If an additional pipe of diameter 20cm and length 1200 m is attached to the last 1200m length of the existing pipe, find the increase in the discharge. f=0.015 neglect minor losses. Ans.Q= 0.0254 m3/s , increase to discharge 0.0088m3/s Ex. Pipe of L=4000m and dia.=0.6m as shown in fig. At a distance of 1000m from the upper reservoir , a small pipe is connected to the pipe line. The water can be taken from the small pipe. Find discharge to the lower reservoir a- No water is taken from the small pipe b-100 liter/sec of water is taken from small pipe. f30.005 neglect minor…
A fire pump delivers water through a 300 mm diameter main to a hydrant to which is connected a cotton rubber lined fire hose 150 mm in diameter terminating to a 25 mm diameter nozzle. The nozzle is 2.5m above the hydrant and 16m above the pump. Assuming frictional losses of 3m from the pump to the hydrant, 2m in the hydrant, 10m from the hydrant to the base of the nozzle, and the loss in the nozzle of 4% of the velocity head in the jet, to what vertical height, in m, can the jet be thrown if the gage pressure right after the pump is 550kPa? Round your answer to 3 decimal places. h 25mm dia. nozzle 2.5m 13.5m 150mm dia. fire hose (2) P H 300 mm dia. main pipe
2. A turbine is used to produce 2700 hp by expanding the water between points 1 and 2. Water flow rate, static pressures and pipe diameters are given. Calculate the power lost in between point one and two. Note that the static pressure at point 2 is given in vacuum. (SGH =13.6) P1 = 60 psi Q = 150 ft³/s D = 3 ft Section (1) Turbine 10 ft P2 10-in. Hg %3D vacuum D2 = 4 ft Section (2)
Find the pressure at point 2 given the isometric drawing of the commercial steel pipeline indicating the straight pipes length and with the following data below:Loss coefficients:• check valve, k = 5.0• gate valves, k = 0.20• elbows, k = 0.75• flowmeter, k = 13.0Pump flowrate = 10 m3/hrFluid power adding by pump = 3.7 HPPressure at point 1 = 60 kPagPipe inside diameter = 50mmViscosity = 0.17 Pa.sSpecific gravity = 0.89Pipe inside surface roughness = 0.00015 ft.