An oil pumping rig is shown in the figure. The flexible pump rod D is fastened to the sector at E and is always vertical as it enters the fitting below D. The link AB causes the beam BCE to oscillate as the weighted crank OA revolves. If OA has a constant clockwise speed of 1.0 rev every 3.7 s, determine the acceleration ap (positive if up, negative if down) of the pump rod D when the beam and the crank OA are both in the horizontal position shown.

An oil pumping rig is shown in the figure. The flexible pump rod D is fastened to the sector at E and is always vertical as it enters the fitting below D. The link AB causes the beam BCE to oscillate as the weighted crank OA revolves. If OA has a constant clockwise speed of 1.0 rev every 3.7 s, determine the acceleration ap (positive if up, negative if down) of the pump rod D when the beam and the crank OA are both in the horizontal position shown.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

in the figure the wheel D rotates with an angular velocity ω1 of 2 rad/s counterclockwise. Find the angular velocity ωE of the toothed wheel E with respect to the ground at the instant shown in the diagram.Note: Solve bar AB and sprocket E by IC method and re-solve it again by the realtive method of velocities.
At the instant shown, the AB bar is rotating counterclockwise with speed and acceleration angles shown in the figure. Determine the (linear) speed and acceleration of the sliding block C at that instant.
The figure is made of rigid members AB, BC, DE, and EF, whichare pinned at A, B, D, E, and F. End C of member BC is pinned to a block which slides on member DE. For the given position, angular velocity of member AB = 2 rad per sec clockwise and angular acceleration of member AB = 3 rad / s^2 counterclockwise. Find the linear velocity and acceleration of the block at C for this position.
An oil pumping rig is shown in the figure. The flexible pump rod D is fastened to the sector at E and is always vertical as it enters the fitting below D. The link AB causes the beam BCE to oscillate as the weighted crank OA revolves. If OA has a constant clockwise speed of 1.0 rev every 2.6 s, determine the acceleration ap (positive if up, negative if down) of the pump rod D when the beam and the crank OA are both in the horizontal position shown. 3.1 m- 3.44 m E 0.93 m 1.92 m 0.6 Answer: ap = m/s?
dynamic slender rods are fixed together as shown at left determine the anguler acceleration of the system when it is released.
Dynamics Lesson For the electric saw shown in the figure, the saw can slide left and right on the horizontal bed where it is placed. Since the engine rotates the crank counterclockwise with a constant angular velocity of 60 dv/min, find the acceleration of the saw and the angular acceleration of the arm AB for the position where ?=90o
The mass of a rocket is m, and its radius of gyration about the mass center C is kC. Determine the thrust T that can cause an angular acceleration of alpha when applied at θ. Calculate the components of the absolute acceleration of point A, ax, ay , caused by this thrust. Point C is the center of mass of the rocket. At the moment considered the angular velocity of the rocket is zero. The gravitational acceleration: g = 9.81 m/s m= 6800kg kc= 3m alpha = 0.24 m/s^2 l1= 6.4 m l2= 6m theta = 5 degree radius of gyration is given with respect to C
If the sprocket S is turning with an angular velocity ?S = 6 rad/s, and anangular acceleration of ?S = 2 rad/s^2. Find angular velocity and angular accelerationof link AB. Note that link AB shares an axis of rotation with sprocket S, but is free torotate separately from S (it’s not attached to the sprocket S). The pin at C is attachedto one of the chain links, and is moving vertically downward.
Find the acceleration of the translating piston at the given instant if w1 = 10 rad/s And a, = -5 rad/s² . Present a, vector 13 in. BAR 2 form. rad/s² az in/s² w1 = 10 rad/s a1 = -5 rad/s² -BAR 1
WA TB RA
Find the angular acceleration of bar BC for the moment indicated in the diagram. Bar AB has a constant clockwise angular velocity of 5.3 rad / s and the dimensions are as follows: x1 = 13 m, x2 = 20 m, y1 = 16 m, y2 = 19 m.
(a) Find the final speed V of the center of mass of the wheel once the wheel starts moving.