Design a logic circuit with four inputs and one output that will produce "1" in the output only if the input patterns have odd number of zeros. a) Write the Boolean equation for the circuit in the simplest SOP form. b) Draw the logic circuit for the above equation in its simplest form. c) Re Design the logic circuit using NAND gates only?

Design a logic circuit with four inputs and one output that will produce "1" in the output only if the input patterns have odd number of zeros. a) Write the Boolean equation for the circuit in the simplest SOP form. b) Draw the logic circuit for the above equation in its simplest form. c) Re Design the logic circuit using NAND gates only?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Design a logic circuit with four inputs and one output that will produce "l" in the output only if the input patterns have odd number of zeros. a) Write the Boolean equation for the circuit in the simplest SOP form. b) Draw the logic circuit for the above equation in its simplest form. c) Re Design the logic circuit using NANI) gates only?
logic circuit diagram for fabinaaci counter that gives output in fabinaaci sequence.upto 2 digits please mentions the gates and ics used in circuit.
Q2/A) Design 8x1 multiplexer using 2x1 multiplexer? Q2 B)Simplify the Logic circuit shown below using K-map then draw the Simplified circuit? Q2/C) design logic block diagram for adding 12 to 5 using full adder showing the input for each adder?
Design a combinational circuit using multiplexer for a car chime based on thefollowing system: A car chime or bell will sound if the output of the logic circuit(X) is set to a logic ‘1’. The chime is to be sounded for either of the followingconditions:• if the headlights are left on when the engine is turned off and• if the engine is off and the key is in the ignition when the door is opened.Use the following input names and nomenclature in the design process:• ‘E’ – Engine. ‘1’ if the engine is ON and ‘0’ if the engine is OFF• ‘L’ – Lights. ‘1’ if the lights are ON and ‘0’ if the lights are OFF• ‘K’ – Key. ‘1’ if the key is in the ignition and ‘0’ if the key is not in the ignition• ‘D’ – Door. ‘1’ the door is open and ‘0’ if the door is closed• ‘X’ – Output to Chime. ‘1’ is chime is ON and ‘0’ if chime is OFF
1. Design a logic circuit with four inputs A,B,C,D as shown in figure1 and one output Y and whose output will be high if only the input is evenly divisible by 3. A B LY D Figure1 I. Find the SOP Boolean expression of the output Y. I. Draw logic circuit using basic gate and verify the result by using any simulation tools. II. Draw a logic circuit by using NAND gate only. |
i) Analyze the logic circuit in Figure Q5(c) and obtain the Boolean expressionfor Z.ii) Construct a truth table from the logic circuit in Figure Q5(c) and explain it.
MNO P D For the given logic circuit, find the following: a. Logic Equation or Output b. Simplified logic expression using Boolean Algebra c. Simplified circuit S
6. For the follow logic circuit system, the output f is: 5 (A) ab. (B) a + b. (C) a'+b'. (D) a'b'. a b
We want to design a circuit to detect prime numbers.The input of the circuit is a 4-bit binary number and the output is a single bit and should show one when the number is prime and zero otherwise.B. Implement the circuit using a 4× 1 multiplexer and combinational logic gates.C. Implement the circuit using only one decoder and one OR gate. What is the size of the decoder you use?
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
a) Design a combinational circuit that would take a 3-bit binary number and generate an output if the input value in decimal is either divisible by 2 or 3. iii) Explain and show how you would implement this circuit using a 4-to-1 Multiplexer and other appropriate logic gates. Use a block diagram for the multiplexer.
Q) You want to design a synchronous counter sequential (sequential) logic circuit. Counting from 9 to 0 and will not count the last digit of your student number. (a) List the steps that you will apply in the design approach. State Chart and State Create the table. (b) Design the sequential circuit using JK Flip-Flop. Explain each step. Desired action show that you have done it. " last digit student num:4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.