Construct a 4-bit Johnson counter using J-K flip-flops. (See Figure 12-12 for a Johnson counter.) What sequence of states does the counter go through if it is started in state 0000? State 0110? FIGURE 12-12Shift Registerwith InvertedFeedbackCengage Learning 2014CLKD3 Q323D2 Q222(a) Flip-flop connectionsD₁ Q₁2₁001011000111100110(b) Transition graph(010101

Johnson counter: The Johnson counter is modified ring counter where the output of the last flip-flop…

Answered: Construct a 4-bit Johnson counter using…

Construct a 4-bit Johnson counter using J-K flip-flops. (See Figure 12-12 for a Johnson counter.) What sequence of states does the counter go through if it is started in state 0000? State 0110?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Related questions

Q: Consider a uniform quantizer that uses 3 bits and whose input ranges from -1 V to +1 V. a. How many…

A: We need to find out number of level and step size and quantization power for given quantization .

Q: Find the expression for the voltage and current of the capacitor as a function of time for the…

A: The voltage and current across the capacitor in the given circuit can be obtained by analysing the…

Q: A coil of 1000 turns is uniformly wound on a ring of non-magnetic material, the mean diameter being…

Q: (1) The system is in steady state. The phasor diagram shows the voltages V₁ and V₁ (but you are not…

A: We need to determine, a) vi(3π/4) b) A value c) the value of capacitor Ca

Q: Calculate the number of Coulombs of charge needed for a current of 2 amps to flow for 14 minutes.

A: Given I = 2A t= 14 Minutes Need to find coulombs of charge(Q).

Q: *16. For the transistor configuration of Fig. 8.108: a. Solve for the currents IB, Ic, and I using…

Q: Q.1/ Determine Vo in the scaling circuit has connected two nodes with inverting input, the first…

A: The given problem is from operational amplifier. The detailed solution is given in the next step

Q: 2. Consider the following: (a) Design a 4 to 1 multiplexer using transmission gates such that the…

Q: If x(t) is a real WSS with an autocorrelation function R(T). Prove that if x(t) has periodic…

A: Given: x(t) is a real WSS with an auto correlation Rτ. To prove: If x(t) has periodic components,…

Q: The intrinsic impedance of a medium is given by "1 impedance in free space is: -12 Hint: -8.854x10…

A: Given data, Permittivity of free space ε0=8.85×10-12. Permeability of free space μ0=4π×10-7.

Q: Q5. The bridge circuit in Figure Q5 below is used to monitor temperature using a thermometer. The…

Q: Given the circuit below, the switch is at position a for a long time. At t=0, the switch is moved…

A: Parallel RC circuit R=15000 ohms C=10*10-6F current source I=2A

Q: maximum power and specify the value of that power. 4/0° A 5 QIA -j10Vx Z₂ 102 R joEz F Z 2Vx A

Q: Design a 3-bit counter which counts in the sequence: 001, 100, 101, 111, 110, 010, 011, 001, ... (a)…

A: We need to design a 3-bit counter which counts in the sequence: 001, 100, 101, 111, 110, 010, 011,…

Q: 0.28 j1.13 A rms

A: Current is given as 0.28-j1.13 A (rms)

Q: Show your solution and supporting explanations. A 100-W, 110-V and a 50-W, 110-V lamps are connected…

A: In this question we need to find the voltage across the 100 W lamp .

Q: (2)Draw the composite sequence network of a phase short circuit grounding.

A: Draw the composite network of a phase short circuit grounding.

Q: 5. A 100 µF capacitor is connected in parallel with a 50 µF capacitor. This combination is connected…

A: Given data, 100 μF and 50 μF capacitors are connected in parallel and then combination is connected…

Q: 1. As shown in figure 2-3, what will be the output signal given the following input signals: a.…

A: The given amplifier will produce the difference in input voltage. Since the associated resistors are…

Q: 3. Determine Vo. 12 V (+) 82 M Vo 252 W +7V

A: Given circuit:-

Q: Explain the circuit below

A: The given circuit is a astable multivibrator using 555 timer. It produces pulse output and the…

Q: 5.1 A three-phase, 5 hp, 208 V, 60 Hz induction motor runs at 1746 rpm when it delivers rated output…

A: Given: In this question, the given details are, A three-phase, 5 hp , 208 V, 60 Hz induction motor…

Q: A three phase 480 V, 50 hp, 6 pole, 60 Hz induction motor has a full load slip of 2.5%. Determine…

A: Given: In this question, the given details are, A three phase 480 V,50 hp,6 pole,60 Hz induction…

Q: 1. Find the currents and determine the voltage per node. 1802 30V- 320 2502 14 15 152 502 d 16 45V с…

A: Given: A network, To find: the currents and voltage per node.

Q: 40. Determine the duty cycle for each waveform in Figure 11- 86 LD.

A: The duty cycle is the ratio of the ON time period to the total time period. Duty Cycle =…

Q: Calculate the cost (in cents) of using a 862 watt appliance for 30 days if used 4 hours per day, and…

Q: SHOW YOUR COMPLETE SOLUTION AND GIVE WHAT IS ASKED. ANSWERS SHOULD BE IN 4 DECIMAL PLACES In a…

Q: Vin = Rs www 26 V Figure 1 Vz=14 RL= 500 to ⁰⁰

Q: Refer to the given circuit below. Whatever the value of the source voltage, which resistance will…

A: We need to find out the current for resistance .

Q: state-space to Discrete using ZOH method with Ts = 1. [4 *(0) = + [2]u(t) v(t) = [1 01x(t) state…

Q: Using Kirchoff's Laws and Ohms Law, determine the branch currents (x,y and z) when the value of each…

Q: II. III. IV. V. What is the effect of load on the efficiency of an induction motor? Explain the term…

A: Since, the question posted by you has multiple sub-parts, we will solve the first three sub-parts…

Q: )Two complex loads Z1 and Z2 are connected in parallel and powered by a value voltage effective 7.2…

A: In this question, We need to determine the total capacity of the combine load and value of…

Q: 1. Find the Laplace transform of the function f(t) = tsin(2t) + e

Q: Assuming identical supplies, determine the unknown currents for the network in Fig 5.

A: The required current can be calculated by using the ohms law and kirchhoff's current law. In…

Q: 3. For the figure below, determine the mode voltages at nodes 1, 2 and 3. (Nodal Analysis) 1 492 292…

Q: Explain the circuit

A: The given circuit is a astable multivibrator using 555 timer and it is used to produce varying pulse…

Q: QUESTION 4 a. Determine the output voltage Vout of each filter in the figure below at the specified…

Q: 8.47 Source Vs in the circuit of Fig. P8.47 is connected to two industrial loads, with equivalent…

A: Given data: Line impedance, ZLine=0.5+j0.3 Ω Industrial load,Z1=8+j12 Ω Industrial load,Z2=6+j3 Ω…

Q: For f(x, y) = e³+13y, find the second order partial derivatives fry and fyz of the functic O 9 e³+13…

Q: Q3. Calculate the branch currents and the total equivalent current of the complete circuit in Figure…

Q: 2. The boost converter has parameter 3. The buck-boost converter has parameters Vs = 12 V, D = 0.6,…

A: Since you have asked multiple questions in a single request, we will be answering only the 1st…

Q: C. A cylinder whose radius is 2 cm and altitude of 100 cm. is uniformly wound with 2500 turns of…

Q: Given the function f(x) = 3x² – 2x on the interval -3 ≤ x ≤3 (a) Find the Fourier series expansion

Q: Explain the circuit below

A: We have to explain the given circuit. The given circuit is drawn in Proteus software.

Q: +V₁ V1 Transistor State: Ix Assume: VBE (on) = .7V, VCEsat = .2V, p = 100 Find the current Ix and…

A: Given, The circuit diagram of the transistor, Base to emitter voltage, VBE=0.7 V, Vce=0.2 V The…

Q: A particle with initial velocity = (5x 10³ m/s) f enters a region of uniform electric and magnetic…

Q: Calculate the complex number and express the result in rectangular form 52-15° 8 2+j3 - 2+j7 +

Q: 4. Find the current in each resistor using Nodal Analysis. 10 20 5 A 30 6V

A: We need to find out the current for given circuit.

Q: Using Norton's theorem to find Vo shown in the figure below.

A: The norton's current can be calculated by short circuit the load terminal and then find the current…

Question

Construct a 4-bit Johnson counter using J-K flip-flops. (See Figure 12-12 for a Johnson counter.) What sequence of states does the counter go through if it is started in state 0000? State 0110?

FIGURE 12-12
Shift Register
with Inverted
Feedback
Cengage Learning 2014
CLK
D3 Q3
23
D2 Q2
22
(a) Flip-flop connections
D₁ Q₁
2₁
001
011
000
111
100
110
(b) Transition graph
(010
101

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

answere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Combinational Logic You are designing a water level circuit using 74ALS151 (8 to 1 Multiplexer IC)* When input is 0000 that means tank is empty.* When input is 1111 that means tank is full.* When input is below 5, that means water level is low.* So, make a circuit using 74ALS151 Multiplexer IC that shows a "low water" indicator light(by setting an output L to 1) when the water level drops below level 5.
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
Digital logic design Solve it with drawing and simulation lab I need them both to have the full solution. And thanks Design counter that counts from 00 to 59, using the IC 74LS90 ripple counter and use two 7 segment display to display the result count. You can also use 7447 binary to 7-segment Display Decoder.
Analyze the logic function of the circuit A₁ B₁ CH D -S₁
Please help me create a 5-bit presettable counter using JK flipflop. Thank you.
3Draw the state table and state graph for fhe following logic cirad A CLK
Explain the function of the 7493 and 7490 ICs. Explain their inputs, outputs, mod number, etc. Provide detailed information about each IC.
From the BCD code whose block diagram is given in the figure below, you can find the 7-segment LED display (with common anode) code. Solving combinational logic circuit will be designed. This type of commercially produced decoder is integrated State the features you consider important by researching the circuits. BCD input at the output of the decoder For the 0-9 values of the information information, the following display figures will be seen and the values other than these it will be considered arbitrary. Since the 7-segment LED display has a common anode, Logic "0" will be applied in response to the burned parts. The accuracy of the logic circuit you will design Create the table and find the output expressions by shrinking the table with the Karnaugh diagram method.
Solve using logic circuits topics
Design a combinational circuit with four input lines that represent a decimal digit in BCD and four output lines that generate the 9's complement of the input digit. Provide a fifth output that detects an error in the input BCD number. This output should be equal to logic 1 when the four inputs have one of the unused combinations of the BCD code. Provide a schematic logic diagram of it. It will surely help me in my review. Thank you so much!
Give the output waveform for Q if the inputs in Figure 4 are fed into a rising edge triggered J-K Flip-Flop assuming that Q is initially LOW. Please answer in typing format please ttt the
From the BCD code whose block diagram is given in the figure below, you can find the 7-segment LED display (with common anode) code. Solving combinational logic circuit will be designed. This type of commercially produced decoder is integrated State the features you consider important by researching the circuits. BCD input at the output of the decoder For the 0-9 values of the information information, the following indicator figures will be seen and the values other than these it will be considered arbitrary. Since the 7-segment LED display has a common anode, The logic "0" will be applied to the burned parts. Draw this circuit.