Question 1: Calculate the a and b parameter values so that (peak time) value is 1 second and (settling time) value is 2 seconds when unit-step input is applied in the system whose form is block diagram below. Calculate the (rise time) and (Maximumum overshoot) values of the system using the parameters you found in section a). Question 2: a) What should be the K value for the following closed system to be at critical damped? b) In what range should the K value be in order for the system given above to be underdamped and overdamped? Question 2:a) What should be the K value for the following closed system to be at critical damped?G(s)R(s)Ks+KH(s)b) In what range should the K value be in order for the system given above to be underdamped and overdamped? Question 1:a) Calculate the a and b parameter values so that t, (peak time) value is 1 second and t, (settling time) value is2 seconds when unit-step input is applied in the system whose form is block diagram below.u(t)y(t)1as+1b) Calculate the t, (rise time) and M, (Maximumum overshoot) values of the system using the parameters youfound in section a).

As per the guidelines of Bartleby we supposed to answer first question only for solution of…

Calculate the a and b parameter values so that (peak time) value is 1 second and (settling time) value is 2 seconds when unit-step input is applied in the system whose form is block diagram below. Calculate the (rise time) and (Maximumum overshoot) values of the system using the parameters you found in section a).

Calculate the a and b parameter values so that (peak time) value is 1 second and (settling time) value is 2 seconds when unit-step input is applied in the system whose form is block diagram below. Calculate the (rise time) and (Maximumum overshoot) values of the system using the parameters you found in section a).

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.30P: Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and...

See similar textbooks

Similar questions

Given the system below, for a unit step input, determine the percentage overshoot **I need a step by step answer please :)
ssignment_2 5 Immersive Reader O Open in Deskt (b) Connected in paralld. 7) The following readings are obtained in the measurement of an inductor: 1.003,0.998, 1.001, 0.991, 1.009, 0.986, 1.005,0.997, 1.008, and 0.994 µH. Determine the (a) Arithmetic mean. (b) Average deviation. (c) Standard deviation.
Consider a PV Module with 4 solar PV cells with the Size of each 10cm x 10cm are connected in Parallel. Choose the correct statement for the above PV Module. (Assume necessary data) a. The output voltage is 0.5 V, the output power is 12W b. The output voltage is 2 V, the output power is 12W c. The output voltage is 12 V, the output power is 6W d. The output voltage is 0.5 V, the output power is 6W
An open loop system with unity feedbak has %OS OF 16%. What is its peak amplitude (Only give numerical value)
TOPIC: STABILITY Subject to a step input, the voltage drop across the resistor took 696.3103us to reach 13% of its steady value from rest. Determine the time (ms) needed to reach 90% of its steady value from 10% Determine the time (ms) needed to reach 80% of its steady value from 20%
Consider a PV Module with 24 solar PV cells with the Size of each 15cm x 10cm are connected in series. Choose the correct statement for the above PV Module. (Assume necessary data) a. The output power is 2.25W and the output current is 0.09A b. The output power is 540W and the output current is 45A c. The output power is 54W and the output current is 2.25A d. The output power is 54W and the output current is 4.5A
) In order to obtain the DC operating points for the circuit in the figure, please redraw the circuit withappropriate changes and explain.(b) The circuit has two DC operating points, please determine both of them.(c) Please find the linear equivalent for each DC operating points. From the two DC operating points you havedetermined, which one of them will give you a negative resistor, when you obtain the linear equivalent.(d) Determine the instantaneous power of the negative resistor for the given circuit.
FACTS: AC-DC converters take the AC power from wall outlets and convert it to unregulated DC. These power supplies include transformers that change the voltage of the AC that comes through wall outlets, rectifiers to save it from AC to DC and a filter that removes noise from the peaks and troths of the AC power waves.The DC-to-AC Converters are used to charge the batteries in the vehicles. These circuits are mainly used for driving low-power AC motors and are used in a solar power system. The DC to AC converters can be used in dc transmission lines for transmitting power to loads. QUESTION: What do you think is the main reason why we have AC power in our outlets instead of DC power? Explain your answer.
Exe: The single-phase bridge rectifier has an RL Load and an ac source, with R = 10Ω andL = 10mH. The peak value of the source is Vm = 100V at 60 Hz. The expressions of voltage andcurrent outputs are:(a) Determine v0(t) and i0(t) with two ac terms (n=2 and 4)(b) Determine the power absorbed by the load.
Using LTSpice, simulate the following circuits and the provide the required information. Provide your observation for each item. 1. Simulate the resistor cube circuit illustrated in Figure 11 to determine the resistance between terminals A to B. validate your simulation result using hand calculation. Figure 11. Resistor Cube Circuit 2. Perform transient circuit simulation for an RC (R=1k, C=1uF) circuit shown in Figure 12 to determine the corresponding output voltage (and current) vs a unit step response input signal. R Vb Figure 12 RC Circuit 3. Create and simulate a hierarchical symbol for an 8-bit, 5V, 200usec digital patterm generator circuit (digital counter) that can be used to validate various digital circuits. Use rise and fall times of 0.1nsec and time delay of 0. Your output should replicate the signals shown in Figure 13 below:
Consider a PV Module with 24 solar PV cells with the Size of each 15cm x 10cm are connected in series. Choose the correct statement for the above. (Assume necessary data) a. The output voltage is 12 V, the output power is 540W b. The output voltage is 12 V, the output power is 54W c. The output voltage is 12 V, the output power is 5.4W d. The output voltage is 24 V, the output power is 2.25W
19. Identify the response time of a meter. a. Time taken by output to reach final constant value from Zero value b. Time taken by output to reach 95% of value from 10% c. Time taken to settle inside 2% of the final value d. None of the options