Ahollow shaft with an external diameter of 150 mm transmits a maximum torque of 13 kNm. The shaft length is 5 m,and the maximum shear stress is limited to 40 MPa. If G = 84 x 103N/mm2 , calculate; 2.1 the internal diameter of the shaft. 2.2 the angle of twist in degrees. 2.3 the minimum shear stress in the shaft.

Ahollow shaft with an external diameter of 150 mm transmits a maximum torque of 13 kNm. The shaft length is 5 m,and the maximum shear stress is limited to 40 MPa. If G = 84 x 103N/mm2 , calculate; 2.1 the internal diameter of the shaft. 2.2 the angle of twist in degrees. 2.3 the minimum shear stress in the shaft.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.4.5P: A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions...

See similar textbooks

Similar questions

A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
1. A solid circular shaft transmits 75 kW power at 200 rpm. Calculate the diameter of the shaft and the maximum shear stress acting on it, if the twist in the shaft is not exceeding 1° in 2 m length of the shaft. Take modulus of rigidity as 102 GPa.
Determine the minimum diameter that can be used for a solid circular steel shaft which is limited to an allowable shear stress of 70 MPa and a maximum angle of twist of 1.5o (degrees) per meter length. Applied maximum torque is 25 KN-m and the overall shaft length is 1.25 meters. Shear modulus = G= 80 GPa Note: When using torsion stress formulas, you must convert the angle of twist from degrees to radians.
A steel shaft is to be manufactured either as a solid circular solid bar or as a circular tube. The shaft is required to transmit a torque of 1200N-m without exceeding an allowable shear stress of 40MPa or an allowable rate twist of 0.75deg/m. The shear modulus of steel is 78GPa. Compute the required diameter of the solid shaft & compute the required outer diameter of the hollow shaft if its thickness is 1/10 of its outer diameter.
What is the minimum diameter of a solid steel shaft that will not twist through more than 3.18 degrees in a 6 m length when subjected to a torque of 14KN-m. What maximum shearing stress is developed? Use G=83GN/m^2.
Calculate the maximum and minimum shear stress in a hollow circular shaft of outer diameter 20 mm and thickness 2 mm, subjected to a torque of 92.7 N-m.
A hollow steel shaft is stressed to 55 MPa by a torque of 100,000 ft-lb. If the inside diameter is 2/3 of the outside diameter and if G = 83 GPa, find the angle of twist in degrees if the shaft is 5 meters long.
A hollow steel shaft is stressed to 35 MPa by a torque of 200000Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter both in mm.