Q.3. The figure shows a planar truss under the giving loading, held in static equilibrium by a pin and a roller at points A and L, respectively. Calculate the forces in truss members DE, DF, GF, and KL, and state whether they are in tension or compression. 1 kip A Во 4 ft 2 kip D E 4 ft 5 kip F 4 ft X 2 kip 4 ft H 4 ft M 4 ft 2 ft 2 ft 1 kip 2 ft 12 ft 2 ft L

Q.3. The figure shows a planar truss under the giving loading, held in static equilibrium by a pin and a roller at points A and L, respectively. Calculate the forces in truss members DE, DF, GF, and KL, and state whether they are in tension or compression. 1 kip A Во 4 ft 2 kip D E 4 ft 5 kip F 4 ft X 2 kip 4 ft H 4 ft M 4 ft 2 ft 2 ft 1 kip 2 ft 12 ft 2 ft L

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.125P: The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A...

See similar textbooks

Similar questions

Problem 2. From the figure below, Given: weight of the cylinder= 350 KN Note: neglect the weight of the bar and friction 350 kN 3m 10.5 m 258 25 40B a. Compute the reaction at A b. Compute the reaction at D c. Compute the tension in cable at B
2 m Roller 2 m 45° 45° A 2 m Pin-Joint 500N 3.1 Determine the reaction forces at the supports of the truss structure. Determine the member forces (FAB, FAD, FAC, Foc, FCD ). Define whether each member is in tension or in compression. Based on your calculations, replace the figure with an equivalent truss structure by removing the zero-force members, if there is any, and sketch its figure (showing dimensions, supports, applied load, 50ON, similar to the figure given above). 3.2 3.3 3.4
The following truss is loaded as can be seen in the image. Find the forces in members DF, DE, and EC. Be sure to state whether the member is in tension or compression. 12 ft 12 ft 12 ft 12 ft 12 ft 12 ft H dige 2 kips D K 9 ft 9 ft 9 ft 9 ft B 310 C E - 4 kips G ARENDE 01 4 kips L M
1. Use the METHOD OF SECTIONS to determine the forces in members AC, BC, and BD of the truss in Figure 1 and indicate whether each of these members is in tension or compression. As usual, show any free-body diagram(s) (including all essential components), and clearly annotate all calculations. Note: You may use the support reactions calculated in Tutorial S2, Problem 3 without repeating the necessary calculations. A E 220° 1 m 25 KN B D 1 m 1 m Figure 1. [ans.: FAC = 51.29 kN (tension); FBC = -22.73 kN (comp); FBD = -16.07 kN (comp)]
1. Use the METHOD OF SECTIONS to determine the forces in members AC, BC, and BD of the truss in Figure 1 and indicate whether each of these members is in tension or compression. As usual, show any free-body diagram(s) (including all essential components), and clearly annotate all calculations. Note: You may use the support reactions calculated in Tutorial S2, Problem 3 without repeating the necessary calculations. А C 220° 1 m 25 KN В 1 m 1 m Figure 1. [ans.: FAC = 51.29 kN (tension); FBC = -22.73 kN (comp); FBD = -16.07 kN (comp)]
3 The figure shows a plana that is held in static equilibrium by two supports at joints A and G. The truss members have negligible masses. Members AB, BC, CD, and GF are oriented horizontally, and the members AG, BF, and CE are oriented vertically. The 20 kN load is oriented vertically and the 30 kN load is oriented horizontally. Calculate the forces in the following truss members and state if they are in tension or compression: a. Member AB b. Member BF mamo c. Member FE org d. Member CE e. Member DE m A 4 m BY K 4 m 4 m 30 kN C E 3 m 4 m 20 kN D Anywers OF DOORN MOnston) DE ODONG fogmpression) es compression) Po Loka
For the plane truss shown, diagonal members BG, CF, CH, and DG are cables which can brace the truss in tension only. Given: P1 = 1 kN, P2 = 3 KN, P3 = 3 kN, P4 = 1.5 kN, a = 3 m, b = 2.25 m, and h = 3 m. What is the force (kN) in member DH? cable cable B A a b P,V P2 Select the correct response: 2.30 2.10 3.25 2.50 cable cable
Statics, Find the force in members CD, CF, and FG of the truss and indicate whether the member is in Tension or Compression, given:P = 220 lbs, L1 = 4 ft, L2 = 6 ft(Use positive values to indicate Tension and negative values to indicate Compression)
Calculate the forces in members BC, BD, and CF for the truss shown in figure. Indicate the tension or compression. The cross sectional area of each member is 1600 mm2. 3 m 3 m 4 m 60 kN 90 kN 4 m Fbc= kN Fbd= kN Fcf= kN
Find the forces in the members AE, DE, and AC of the truss shown Assign a tension or compression value to each member. Using methods of sections -10 ft- A 14 ft 15 kips B F 5 ft D E 40 kips -10 ft- C GO 5 ft 6 ft ✓ 10 ft
Find the force in each member of this space truss. Interpret your results to state whether each is in tension or compression. Answer: AD = 300 lbf (C) 450 lbf (C) BD= CD= 568 lbf (C) 10 ft 5 ft D 10 ft 5 ft 1000 lb B 5 ft 10 ft 2 ft
Calculate the force in member GH of the truss and indicate whether it is in tension or compression, using either method of joints or method of sections. Required: Draw the FBD(s) as needed for analysis-all equilibrium equations must correspond to a FBD that you have drawn. Make sure to clearly indicate which FBD your equation(s) correspond to. K J H 4 ft C - 3 ft 3 ft -- 3 ft- 3 ft-3 ft 1500 lb 1500 lb 1500 lb 1500 lb 1500 lb