A 3-ph, 50 Hz, 150 km length O.H.T.L. supplies a load with P MW load at 0.85 lag P.f. and 69 kV where P is the last two digits (from right) of your registration number (i.e for the student that has a registration number 202112396, P = 96.. This T.L has a resistance of 0.232 Q/km and an inductive reactance of 0.783 Q/km and the capacitance to neutral is 0.0446 µF/km. Using nominal circuit, Find: 1- Constants A, B, C, and D. 2- Sending end voltage. 3- Sending end current 4- Voltage regulation of this T.L. 5- Transmission line efficiency. 6- Draw with a scale the phasor diagram of this model at this operating case. 7- Estimate approximately the loadability of this transmission line at this operating voltage. Justify your estimation and suggest a way to increase this loadability. Verify your answer.

A 3-ph, 50 Hz, 150 km length O.H.T.L. supplies a load with P MW load at 0.85 lag P.f. and 69 kV where P is the last two digits (from right) of your registration number (i.e for the student that has a registration number 202112396, P = 96.. This T.L has a resistance of 0.232 Q/km and an inductive reactance of 0.783 Q/km and the capacitance to neutral is 0.0446 µF/km. Using nominal circuit, Find: 1- Constants A, B, C, and D. 2- Sending end voltage. 3- Sending end current 4- Voltage regulation of this T.L. 5- Transmission line efficiency. 6- Draw with a scale the phasor diagram of this model at this operating case. 7- Estimate approximately the loadability of this transmission line at this operating voltage. Justify your estimation and suggest a way to increase this loadability. Verify your answer.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
Driving-point admittance The actual impedance of a load is 30 OHM. The per-unit impedance of the load is 0.5 pu when Base Voltage is 600 V and Base Power is of O 6000 VA O 8000 VA O2000 VA 4000 VA Jump to ncements MacBook Air DD DII F10 F9 F8 000 F7 F6
A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The two machines operate in parallel in a power station. What is the equivalent. H constant for the two, relative to a 100 MVA base?
Choose the supply voltage for a step down chopper circuit which drives the resistive load 4.80 with average load current 32.4A for a duty cycle of 0.4. O a. 2624.400 O b. 777.600 O c. 48.000 O d. 388.800
If E = 1.05 p.u. leading by 25 degrees, feeding infinite bus bar through a reactance of 0.35. Find the reactive power flowing. a. 0.138 b. 1.514 c. 2.618 d. 0.43
Problem 2 The circuit diagram of a certain load is presented below. Determine the following: a. The power factor of the load. b. If the load is connected across a 400 Vrms source, determine the real and reactive power consumed by the load. c. From (b), determine the value of the capacitor to be placed in parallel with the load in order to improve the power factor of the load to 95% lagging. From (b), A synchronous motor is installed in parallel with the load to correct the pf. The motor is rated 5 hp operating at 60% efficiency. Assuming that the motor is running at rated power. Determine the apparent power and power factor of the motor in order to improve the load's pf to 95% lagging. 202 500 µF HI + VL -20 mH 5Ω >0.5VL m 15 mH
You have been asked to investigate the loading effects on an alternator supplying a load and also charging a car battery at the same time. The output of the alternator has been rectified to smooth dc, and the circuit is shown below. Using Kirchhoff analysis, determine the initial current in each section along with its direction and the potential difference across the load.
Draw the sinusoidal waveform of the AC voltage and current for the given loads below. Describe the characteristics of the waveform for each load. A. Pure resistor B. Pure inductor C. Pure capacitor
(c)[ device needs to connect to a Diesel generator which generates sinusoidal AC power at 16.67 Hz. The amplitude or RMS value of the generator output voltage is adjustable. The area of cross-section of the core is 0.035 m². What constraints, if any, must be imposed on the The magnetic device of the figure is designed to operate with 240 V(rms) at 50HZ. For operation in a remote mining site, the use of this device, or the generator, if the device must be connected to the generator. You may assume that the peak B field in the core must be limited to 1.1 T to prevent magnetic saturation.
A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of158 volts, 50 Hz supplies the combination. Determine the following:a. Circulating currentb. Voltage across the resistorc. Voltage across the capacitord. Real power supplied by the source
A load is operating in a chopper circuit as shown in the figure. It has a duty cycle of 0.4 and chopping frequency is 150 Hz. (consider continuous operation). The value of E is L=0.06H 200V (B) 80V (D) 50V (A) 70V (C) 60V
One side of a transformer has What is the voltage (in V rms) at the secondary? 1,800 turns while the other side has 450 turns. The high voltage side is connected to a 240 Vrms source. The low What is the current (in A rms) at the secondary? What is the current (in A rms) out of the source? What is the value of the load impedance when referred to the primary? • Referred impedance = voltage side (secondary) is connected to an impedance ZL = 20 + j10 Q. Provide at least 4 digits after the decimal point. +j_ N What is the value of the source voltage (in V rms) when referred to the secondary?