Unless given, use the: POLAR FORM for voltage and current, RECTANGULAR FORM for impedance. Consider the following circuit, supplied by a 10VRMS Voltage source with a 0° phase shift (i.e. Vsource = 1020° V). V2 R1 C2 sine 50 Hz 100 320 µF a. What is the total impedance of the circuit? b. What is the total current drawn by the system? c. Is the circuit inductive, capacitive, or neither (resistive)? d. What is the total power (apparent) delivered by the voltage source? e. Draw the phasor diagram of the voltage and current at the source. f. What is the power drawn by the 100ohm variable resistor? g. If the variable resistor is set to 200-ohms, instead of 100-ohms, i. What is the power drawn by the 200-ohms resistor? H What is the total current of the system? ell L1 160 mH

Unless given, use the: POLAR FORM for voltage and current, RECTANGULAR FORM for impedance. Consider the following circuit, supplied by a 10VRMS Voltage source with a 0° phase shift (i.e. Vsource = 1020° V). V2 R1 C2 sine 50 Hz 100 320 µF a. What is the total impedance of the circuit? b. What is the total current drawn by the system? c. Is the circuit inductive, capacitive, or neither (resistive)? d. What is the total power (apparent) delivered by the voltage source? e. Draw the phasor diagram of the voltage and current at the source. f. What is the power drawn by the 100ohm variable resistor? g. If the variable resistor is set to 200-ohms, instead of 100-ohms, i. What is the power drawn by the 200-ohms resistor? H What is the total current of the system? ell L1 160 mH

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q1. following: For the circuit shown in figure (a). Let V1 = 10Vms, frequency 10KHZ. Draw the A. Impedance diagram. B. Voltages phasor diagram. C. Current phasor diagram. D. Measure the voltage across R1,R2, Vin, and the inductor using the ocillscope using PROTEUS software. E. Measure the voltage in R1, R2, and the inductor using DMMby using PROTEUS software. F. From the above measurments verify your result. R2 1K V1 VSINE R1 L1 2K 1000M
The waveforms below represent one full cycle of the applied voltage vs and the supply current is. based on the waveforms below, which of the following statements is true. options: is leads vs is lags vs is is in phase with vs
A chopper circuit has an inductive load of 2ohm resistance and 10mH inductance. If the source voltage is 20 V and the frequency of the chopper is set to 100Hz and the on-time to 5 ms. Determine the average voltage and current, maximum and minimum load currents.
Derive the expressions of voltages across resistor and capacitor and the current through the circuit in charging and discharging phases of an RC circuit excited by DC voltage. Name some uses of transient currents. 2.
Complete solution and add phase angles. Please put clear derivation of formulas. Thank you.
a) We assume that the switch is on. Calculate the reactance values and find the charging current in the circuit below. Is the circuit capacitive or inductive? Show that the voltage across the capacitance can be slightly larger than the source voltage U. (This is called the Ferranti effect and means that we can get a voltage rise beyond overhead lines with small loads. This is mostly relevant at the highest voltage levels. The frequency f is 50Hz, and assume voltage U= √2⋅24kV
A resistor and a capacitor are connected in series across a supply of 250 V. When the supply frequency is 50 Hz the current in the circuit is 5 A. When the supply frequency is 60 Hz, the current is 5.8 A. Find the value of the resistance. Ans: ___ ohms
A 120 V, 60 Hz power source is connected across an 800 ohm resistance in series with an unknown capacitor. The voltage drop across the resistor is 102 V. Find the, a.) current of the circuit b.) impedance of the circuit c.) Capacitive reactance d.) capacitance value.
An inductor of 150hms and resistance of 10 Ohms are connected in series to a 230V, 50 Hz ac supply. Determine the active and reactive power and power factor in the circuit.
Find the DC value and RMS value from this image in below. , I want the solution in a detailed picture with a white paper and a clear font. Thank you.
A circuit consists of an AC voltage source, a 10-ohm resistor, and a capacitor, all connected in series. The magnitude of the impedance of the capacitor is also 10 ohms. Which of the following is true about the source voltage and the current through the circuit? a. Insufficient information is given. b. The source voltage will lag the current. c. The source voltage will lead the current. d. The source voltage will be in-phase with the current.
Given the circuit in Figure 04 and defining that: Vs = 100 sin (wt) Volts and the firing angle of the thyristors T1 and T2 is equal to 110° and that T3 and T4 have similar firings in the negative half-cycle of Vs. a)Sketch the output voltage waveform for a highly inductive load. b) Sketch the waveform output voltage, replacing the highly inductive load with a purely resistive load. c) Get the value of the average output voltage when the load is purely resistive.