A,B,C,D. FINISH ALL . 6. A 240-Vrms 50-Hz supply serves a load that is 10 kW (resistive), 15 KVAR(capacitive), and 22 kVAR (inductive). Find:(a) The apparent power;(b) The current drawn from the supply;(c) The KVAR rating and capacitance required to improve the power factor to 0.96;(d) The current drawn from the supply under the new power-factor conditions.

In this question we will find power , current etc... Note:. As per our guidelines, I am supposed to…

A 240-Vrms 50-Hz supply serves a load that is 10 kW (resistive), 15 kVAR apacitive), and 22 KVAR (inductive). Find: O The apparent power; ) The current drawn from the supply; The kVAR rating and capacitance required to improve the power factor to ) The current drawn from the supply under the new power-factor conditio

A 240-Vrms 50-Hz supply serves a load that is 10 kW (resistive), 15 kVAR apacitive), and 22 KVAR (inductive). Find: O The apparent power; ) The current drawn from the supply; The kVAR rating and capacitance required to improve the power factor to ) The current drawn from the supply under the new power-factor conditio

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
Find the complex power and power factor for the indicated element(s).( need only handwritten solution .otherwise downvote.)
The total power drawn by the two-impedance load in parallel is 26kW at 0.98 power factor lagging, it is being supplied by a 230-volts AC source. One of the loads (Load 1) takes 16kVA at 0.77 power factor lagging. What is the reactive power of the unknown impedance (Load 2)?
(b) An inductive load consisting of resistor, R and inductor, L in series feeding from a 240430° Vrms, 50 Hz supply consumes 6 kW at lagging power factor of 0.88. (i) Determine the current through the load. (ii) Find R and L. (iii) Draw the phasor diagram of supply voltage and current.
The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
A parallel connection of a RL branch with a C branch is connected across a 100V AC mains. At first R = 10 ohms, L = 20mH and frequency of 1000rad / s, the current measured is 2.2361A at 89.44 leading power factor. A) Determine the initial capacitance. B) However, a fault occurs on the capacitor branch making its capacitance 20% lower and a resistance of 5 ohms is detected. If this faulty circuit is rerun but at a frequency of 500 rad / s, determine the new current that will flow through the circuit.
Draw the sinusoidal waveform of the AC voltage and current for the given loads below. Describe the characteristics of the waveform for each load. A. Pure resistor B. Pure inductor C. Pure capacitor
(a) A very important parameter in AC power circuits is power factor. Justify this phrase. Then, explain the difference between leading and lagging power factor. Describe the phase relationship between voltage and current for these two conditions to support your answer.
A single phase AC chopper supplies a pure inductive load of 0.02H from 220V, 50HZ AC supply. The triggering angle of the thyristors is 100°. (Assume the circuit is ideal.) a. Sketch the circuit b. Develop the load current expression and find the decay angle of the load current c. Sketch the load voltage and load current waveforms d. Calculate the RMS value of load voltage e. Calculate the RMS value of load current f. If the triggering angle of the thyristors is chosen as 60°. Explain the operation of the circuit.
A 120V adjustable frequency ac source is connected in series with a resistor, an inductor, and a capacitor. At 60Hz, the resistance is 5 ohms, the inductive reactance is 3 ohms, and the capacitive reactance is 4 ohms. Compute: (a)load impedance at 60Hz (b) value of the capacitance and inductance Explain each step. Please recheck
A 120 V, 60 Hz power source is connected across an 800 ohm resistance in series with an unknown capacitor. The voltage drop across the resistor is 102 V. Find the, a.) current of the circuit b.) impedance of the circuit c.) Capacitive reactance d.) capacitance value.
A 120V adjustable frequency ac source is connected in series with a resistor, an inductor, and a capacitor. At 60Hz, the resistance is 5 ohms, the inductive reactance is 3 ohms, and the capacitive reactance is 4 ohms. Compute: (a)load impedance at 60Hz (b) value of the capacitance and inductance Explain each step.