Answered: A house has an ave. consumption of 26…

A house has an ave. consumption of 26 kVar and 30 kW. Vrms = 230 a. what is the average current (in A rms) b. what is the effective impedance

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.3P: The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous...

See similar textbooks

Related questions

Q: Q2 (a) A 440 V, six poles, 80 hp, 60 Hz, Y connected three phase induction motor develops its full…

A: Given A question on three phase induction motor.we need to solve for rotor resistance. Please find…

Q: Find the complex conjugate number 12 + 5j, Select one: O a.-12-5j O b. 12+5j O c. -12+5j O d. 12-5j…

A: For complex conjugate of any number a+jb is a-jb

Q: 2. What would be the voltage on the secondary side of a transformer with a 400:20 turns ratio and a…

A: Given, Transformer with turn ratio, N1N2=40020 Primary voltage, V1=6000 V

Q: :Q2: find Z equivalent if the frequency is 50 R3 R2 R1 552 792 3052 3mF Zeq :4mF 2H

Q: 7.05 Three 30:1 step down transformers are connected wye-delta for stepping down th 132,000-volt…

A: Given, KVA rating = 5000 KVAtransformer ratio = 30:1 (step down Xer)V1L = 132 KVV2L =?KVA =? VP1…

Q: A capacitor is constructed from two conductive metal plates 30cm x 50cm which are spaced 6mm apart…

Q: For the circuit below with E = 10 V, R = 5800 N. Find the following: a) current in the circuit b)…

Q: In a communication channel the power of the signal is 75 mW and the power of the noise is 50 µW.…

A: Given a communication channel with, Power of the signal, SP=75 mW Power of the noise, SN=50 μW

Q: What will be the reluctance of a magnetic core if the mean path length for flux is 0.04 m and the…

A: We need to find out the reluctance for given details

Q: If a = 0.98, Ico= 6 µA, & lg = 100 µA for a transistor, then the value of lc will be (1.) 2.3 mA…

A: Given, α=0.98ICO=6 μAIB=100 μA

Q: A Four pole, 50kW, 250 Volt Long Shunt DC Machine Motor has a shunt field current of 1.5 A. It is…

Q: A 460 V series motor runs at 500 rpm taking a current of 40 A. Calculate the percentage change in…

A: Given a series motor with, Terminal voltage, V = 460 V Speed, N=500 rpm Current, I1=40 A Percentage…

Q: What is the Baud rate for M-ary digitally modulated carrier if M = 8 and channel capacity= 2.7 kHz

A: It is given that: M=8fb=2.7 kHz

Q: Determine the Fourier transform of the following: a. sgn(t) b. eat c. sin wot d. cos wo t e. theat

A: As per the guidelines of Bartley we supposed to answer first three subpart only.

Q: 2. What would be the voltage on the secondary side of a transformer with a 400:20 turns ratio and a…

A: 2)Let the voltage at primary be V1 and secondary be V2. Then V2/V1=N2/N1 Therefore…

Q: PROBLEMS P6.1 Utilizing the Routh-Hurwitz criterion, determine the stability of the following…

A: Given polynomials, a s2+5s+2b s3+4s2+8s+4

Q: E₂ 18 V 1. For the above circuit: R₁ 6 Ω HI R₂ 3Ω R₂ 6 Ω

Q: Determine the (a) conductivity and (b) resistivity of an intrinsic germanium semiconductor at a…

A: For Germanium at 300 K, Intrinsic carrier concentration: ni=4×1013 cm-3electron mobiliy: μn=5800…

Q: Q1: A. a lossless transmission line, with a length of 0.22, has an equivalent inductance 2500 time…

A: Given A lossless transmission line and we need to determine the characteristic impedance, load…

Q: (2-3) A series-circuit consist of a foreword biased diode, and tow resistances of 3300 and 4700 are…

Q: Amplifier No. 1 2 3 Table 1.0 NF (dB) 2 T₁ (K) 290 Gain (dB) 11 13 16

Q: A medium-rise building with inductive loads has an average consumption of 40 kW and 26 KVAR. At the…

A: As per the guidelines of Bartley we supposed to answer first three subpart only for solution of…

Q: Q1: A. a lossless transmission line, with a length of 0.22, has an equivalent inductance 2500 time…

A: As per the guidelines of bartleyby i should answer first three subparts only so Kindly repost other…

Q: 3. Describe types of Starters used in three phase induction motor and their Function.

A: The huge current flowing inside an induction motor immediately after switching on supply creates…

Q: The amplitude of 12πcos(300t) =12 True O False

A: We need to tell about whether the given statement is true or false

Q: Which wireless system has the maximum range? O Bluetooth O Wi-Fi O ZigBee O IR

A: Answer: Wi-Fi Explanation: a. It is not a valid option. It covers in the range of 10-30meters. b.…

Q: D7.2. A current filament carrying 15 A in the a, direction lies along the entire z axis. Find H in…

Q: Calculate the value of the vector current density: (a)in rectangular coordinates at P₂(2,3,4) if H =…

A: Given data, PA=(2,3,4)PB=(1.5,90°0.5)PC=(2,30°,20°)

Q: FFEREN 1. y" + 5y' - 4y = 0

Q: 2. Simplify the Boolean function F = ((XY+XYZ) + X(Y + XY))?

A: Given data : Boolean function F= XY'+XYZ+XY+XY''

Q: find Z equivalent if the frequency is 50: R1 R3 ww R2 mw 552 792 3052 :3mF Zeq 4mF 2H

Q: Solve for the general expression of the complex gain (Vo/Vs) of the given RLC circuit. The Vs is…

Q: R₁ 6 Ω 4₁ 2 A R₂ R4 302 4 Ω 4. Find the Thévenin equivalent circuit for the network external to the…

Q: A three-phase 6-pole 400-volt cylindrical-rotor synchronous machine has negligible arr resistance…

A: In this question we will find operating speed of synchronous motor.....

Q: What maximum voltage can be connected across a 0.5 W, 270 2 resistor without exceeding the rated…

A: Given: Power rating, P = 0.5 W Resistance, R = 270 Ω

Q: Q1 (a) With aid of suitable diagram, explain the losses and power-flow of an induction motor.

Q: Question 3 options: Fuses and breakers should be circumvented in order to make a shorter circuit.…

A: Given A multiple choice question based on electrical safety. Please find the below attachment for…

Q: Resistors, 10 ohms and 15 ohms, are connected in series. The power being consumed by the 10-ohm…

Q: For a BJT, Ic=5 mA, Ig = 50 μA and ICBO = 0.5 μA, then the value of ß is?

Q: problem: Find the state equations For į (the current of inductor) and ve in the circuit below. 1.n…

Q: The power of a heater is 500 W at 800 °C. What will be the power at 200 °C? Temperature coefficient…

A: In this question we need to find a power at 200oC .

Q: Q4. Draw the circuit diagram, and output waveforms of a three phase full-wave controlled rectifier…

A: Three phase full wave controlled rectifier firing angle =α=60 ° Note: Load type is not provided , we…

Q: Q1:- calculate the total current shown in figure (2-37). 100 Ω 100 v Ξ V 60 Ω 40 Ω Σ88 Ω Figure…

Q: Using the superposition theorem, find Vx in the following circuit. 2002 Vx 4A340 0.1Vx 20V Hi

A: Given circuit:

Q: A 4-pole turbogenerator is rated at 150 MVA, 14 kV and 60 Hz. Its inertia constant is 12 MJ/MVA. If…

A: Given, A 4-pole 14 kV turbo generator with G=150 MVAf=60 HzH=12 MJ/MVAPi=80 MWPe=60 MW

Q: (2-2) An ideal germanium diode at a temperature of 125°c has a reveres saturation current of 30μA.…

Q: Q2:- calculate the electrical energy consumed by T.V. (250V) during one Month if this T.V used (3…

Q: SKVA, 50Hz, single phase transformer, the primary voltage of the transformer is 110V. Reqand X is…

A: Given data, Voltage (Vp)=220 VResistance(Req)=026ΩImpedance(Xeq)=0.4ΩVoltage…

Q: A parallel-plate capacitor with area 0.400 m² and plate separation of 2.00 mm is connected to a…

A: Given, A parallel plate capacitor Area of plates, A=0.400 m2 Plate separation, d=2.00 mm Supply…

Q: Block diagram

Concept explainers

Digital Integrated Circuit Design

Digital IC design is a procedural interaction that involves converting determinations and highlights into computerized blocks, which are then further transformed into basic circuits. A significant number of the imperatives related with advanced IC plan come from the foundry cycle and innovative restrictions.

Question

A house has an ave. consumption of 26 kVar and 30 kW. Vrms = 230
a. what is the average current (in A rms)
b. what is the effective impedance

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

P-channel Metal-Oxide Semiconductor (PMOS), N-channel Metal-Oxide Semiconductor (NMOS), and Complementary Metal-Oxide Semiconductor (CMOS)

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous current entering the positive terminal of the circuit element is i(t)=100cos(t+10)A. For both the current and voltage, determine (a) the maximum value, (b) the rms value, and (C) the phasor expression, using cos(t) as the reference.
Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
The maximum transferred average power to a load without restrictions calculated in terms of the RMS (effective) value of Vth is: Select one: O a. IVthl/Rth O b. Vthl2/4.Rth OC. IVl²/8.Rth O d. IVl²/2.Rh
A single phase AC chopper supplies a pure inductive load of 0.02H from 220V, 50HZ AC supply. The triggering angle of the thyristors is 100°. (Assume the circuit is ideal.) a. Sketch the circuit b. Develop the load current expression and find the decay angle of the load current c. Sketch the load voltage and load current waveforms d. Calculate the RMS value of load voltage e. Calculate the RMS value of load current f. If the triggering angle of the thyristors is chosen as 60°. Explain the operation of the circuit.
13 ) RMS value of sinusoidal voltage is given by Vrms= 5 V, Calculate the value of peak voltage Vm? a. 1.4142 V b. 5 V c. 3.535 V d. 7.07 V
electric units a & b are connected in parallel and its rms current is 15A. If the current in b lags behind a by pi/3 rads and the current is 23.4 A. find the current in b and sketch the equivalent circuit diagram
compute the RMS value for the current waveform and ys them to determine average power supplied to the resistor....
two devices are connected across a source where F= 60 Hz. If the 2 rms values of the voltage drops across the devices are 115V and 90V which are out of phase by 90°. Find the equation across the source and sketch the equivalent circuit diagram.
An industrial installation has a power factor of 0.85 in backward. The demand is 150 KVA, and the operating voltage is 4800 V at 60 Hz. What should be done to bring the power factor to 0.95 in lagging? Indicate what you would connect and with what three-phase power. If the connection of the element to be added is in delta, indicate its reactance and the value of its capacitance or inductance. capacitance or inductance.
(b) An engineer is required to analyse a sinusoidal waveform for the voltage and current using oscilloscope. The voltage waveform produced Root Mean Square (RMS) value at 75 V with positive-going zero crossing at 30°. While the RMS value of current is 66.71 A with negative-going zero crossing at 0.349 rad. Assume the frequeney of both waveforms is 50 Hz. (i) Sketch the voltage and current waveform in the same axis by showing the important point. (ii) Determine instantaneous voltage when t = 8ms . (iii) Determine phase relationship between voltage and current waveform.
For the circuit in the figure below, determine the load impedance that maximizes the average power drawn from the circuit in the figure below. What is the maximum average power?