-6i - 20 10in- laminate substrate Fig.2 Q2: The tool shown in Fig.2 is used in a gluing operation to press a thin laminate to a thicker substrate. If the wheels at points A and B both have 2 in diameter and have frictionless bearings, and a 20 lb vertical force to the handle of the tool, determine the forces applied to the top of the laminate and the bottom of the substrate.

-6i - 20 10in- laminate substrate Fig.2 Q2: The tool shown in Fig.2 is used in a gluing operation to press a thin laminate to a thicker substrate. If the wheels at points A and B both have 2 in diameter and have frictionless bearings, and a 20 lb vertical force to the handle of the tool, determine the forces applied to the top of the laminate and the bottom of the substrate.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 1 The SERO CHIENS C is recreating rolling large stone columns by animal power and pivot points cut into the center of each of the column. The friction in each pivot point plus the rolling resistance creates a resisting couple of 300 ft*lb (like a rusty bearing). The yoke angle B = 10°. a) Determine how many horses (i.e. horsepower https://en.wikipedia.org/wiki/Horsepower) they need to move a 4600-lb column that is 10 ft long and 2 ft in diameter up a 0 = 5° slope from rest to 3 miles per hour after 15 feet of travel. b) Determine how many horses they need to maintain a constant speed of 3 mph up the slope. Round your answers up to the nearest integer. A fraction of horse doesn't pull very well. Assume the column rolls without slipping.
6.10. A car with its brakes locked will remain stationary on an inclined plane of dry concrete when the plane is at an angle of less than 45° with the horizontal. What is the coefficient of static friction of rubber tires on dry concrete?
A weight of 200lbs. rests on an inclined plane that makes an angle of 35° with the horizontal. If the coefficient of friction is 0.30, what force must be applied parallel to the plane in order to start uniform motion upward?
A cylindrical tank having a diameter of 16 cm weighing 100 KN is resting on a horizontal floor. A block having a height of 4 cm is placed on the side of the cylindrical tank to prevent it from rolling. What horizontal force must be applied at the top of the cylindrical tank so that it will start to roll over the block. Assume the block will not slide and is firmly attached to the horizontal floor. Pls show complete solution with figures.
(a) The rope is wrapped exactly once around a post. The load side is 250 Newtons, the input side is 125 Newtons. What is the coefficient of friction of the rope around the post? (b) If the coefficient of friction was 0.33, 75 pound input , and wrapped as shown below, what load can you handle in pounds? (c) If the coefficient of friction was zero , 250N input, and wrapped three times around the mandrel, what load can you handle?
Consider a 14.5 kg rectangular block of length 0.40 m attached to a spring with a spring constant of 30.5 N/m. The coefficient of static friction between this block and the surface is 0.310.
if the distance between the fulcrum and the center of the mass of the bottles is 0.75m and the distance between the fulcrum and the jar is 0.42 meters, what is the ideal mechanical advantage of this lever? Show work. (the lever is below, ignore the part about the hotspots.)
Situation 1: A 50 N block rests on a surface that is inclined by e degrees. If u: = 0.35 and uk = 0.15, determine the following: A. The maximum e where the motion impends (degrees) B. If e = 15°, what is the frictional force between the block and the incline? (N) C. If e = 25°, what is the frictional force between the block and the incline? (N)
PROBLEM 1 A block of 200 kg mass rests on a rough horizontal plane. Find the force required in each of the following cases: (a) to just pull the block by a horizontal force P, (b) to just pull the block by an inclined force P inclined at 30° to the horizontal, and (c) to just push the block by a horizontal force P. The coefficient of static friction between the contact surfaces is 0.3. 30° Fig. 6.11(a) Fig. 6.11(b) Fig. 6.11(c)
2. A square threaded screw of mean diameter 25 mm and pitch of thread 6 mm is utilised to lift a weight of 10 kN by a horizontal force applied at the circumference of the screw. Find the magnitude of the [Ans. 966 N] force if the coefficient of friction between the nut and screw is 0.02. A bolt with a squore threaded screw has mean diameter of 25 mm and a nitch of 23 mm It carries an
Q2 / The arm of patient was placed into traction, stretch of the shoulder from a length of 0.56 m to 0.562 m. The shoulder has diameter 2.06 cm. Note that the bone has Young's modules of 1.6 x 1010 in tension, what force was used to stretch the shoulder?
a b c d h 82 mm 139 mm 39 mm 18 mm 33 mm Clamps like the one shown are commonly used in woodworking applications. This clamp has the dimensions given above, and its jaws are 38 mm wide (in the direction perpendicular to the plane of the picture). The screws of the clamp are adjusted so that there is a uniform pressure of 190 kPa being applied to the workpieces by the jaws. Find the force carried in each screw.Note: Assume that A, B, C, and D act as pins. (Denote tension forces with positive values; compressive forces with negative values.)