is recreating rolling The large stone columns by animal power and pivot points cut into the center of each of the column. The friction in each pivot point plus the rolling resistance creates a resisting couple of 300 ft*lb (like a rusty bearing). The yoke angle B = 10⁰. a) Determine how many horses (i.e. horsepower https://en.wikipedia.org/wiki/Horsepower) they need to move a 4600-lb column that is 10 ft long and 2 ft in diameter up a 0 = 5° slope from rest to 3 miles per hour after 15 feet of travel. b) Determine how many horses they need to maintain a constant speed of 3 mph up the slope. Round your answers up to the nearest integer. A fraction of horse doesn't pull very well. Assume the column rolls without slipping.

is recreating rolling The large stone columns by animal power and pivot points cut into the center of each of the column. The friction in each pivot point plus the rolling resistance creates a resisting couple of 300 ft*lb (like a rusty bearing). The yoke angle B = 10⁰. a) Determine how many horses (i.e. horsepower https://en.wikipedia.org/wiki/Horsepower) they need to move a 4600-lb column that is 10 ft long and 2 ft in diameter up a 0 = 5° slope from rest to 3 miles per hour after 15 feet of travel. b) Determine how many horses they need to maintain a constant speed of 3 mph up the slope. Round your answers up to the nearest integer. A fraction of horse doesn't pull very well. Assume the column rolls without slipping.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Flat belt 100mm wide and 8mm thick transmits power between two pulleys, running at 1600 m/min. The mass of belt is 0.9kg/m length, the angle of lap in the smaller pulley is 1650 and the coefficient of friction between the belt and pulleys is 0.3, If the maximum permissible stress in the belt is 2MN/m2, find the maximum power transmitted. 1 Add file
d) A leather round belt transmit power from small pulley rotates 1200 rpm. The diameter of small pulley is one third of the diameter big pulley. The center distance between the pulleys is twice the diameter of big pulley. The stresses in the belt should not exceed 2 MPa and belt density is 950 kg/m?. Due to the friction of rotation, the ratio tension on the tight side to the slack side is 2:1 and coefficient of friction is 0.35. For design requirement, the ratio of diameter leather round belt to diameter of small pulley is 1:18. Determine, i) Contact angle. i) Diameter belt. iii) Belt tension. iv) Torque.
4. A small race car has an aluminum hub (shown in red). The drive axle is press-fit into the hub, resulting in compressive pressure and torsional friction as shown below when the wheel is powered. Assuming a coefficient of static friction of 0.3 and a shear yield strength of 30 ksi for the shaft, determine the maximum allowed contact pressure, p (in psi). In other words, how much contact pressure (and resulting torque) would cause yielding of the shaft? Given: d=0.75in, w=1.5in f: Friction force per unit area p: Normal force per unit area
Provide step-by-step solution with complete given and formula to this problem. Draw sketch also. A mine hoist is to carry a cage loaded with ore at a total load of 8 tons. The depthof mine shaft is 328 ft. A 6 x 19 IPS wire rope with rope diameter of 1.75 in is to beuse with sheave diameter of 39 in. The cage loaded is to start from rest and will attaina maximum velocity of 525 fpm in 10 seconds. Find the total load of the rope. A. 12,086 lbs B. 14,086 lbs C. 16,086 D. 18, 086 lbs
An automatic door lock system is to be designed for automatically locking/unlocking car doors. The design will utilize an electric solenoid with sufficient force and stroke to provide the necessary motion. If the force required to drive the lock linkage is 9.5 N, determine if the solenoid with the following specifications meets this requirement: Number of turns Current Air gap Plunger dia, 2500 1.0 Amps 10 mm 18 mm The initial force available from a solenoid F P=2(ND)² HA 82
The following data is refers to a screw jack. The vertical load on the screw320kN Force applied at the lever end whose length=80cm The mean radius of the screw=2.5cm Pitch of the screw=1cm Co-efficient of friction between the screw thread and the nut=0.15 Determine the force on the lever end while raising the load and efficiency of the screw jack
4. The weight of each wheel of a motor driven traveling crane moving at 600fpm is 5800 Ibs. If the coefficient of rolling friction is 0.05, find the horsepower required to overcome friction. 5. Compute the force necessary to move a 6000 lbs supported on four wheels of 2.5 ft diameter, assuming the coefficient of rolling friction to be 0.007.
An extra flexible 8 x 19 steel wire rope of 38 mm diameter is used with a 2 m diameter hoist drum to lift 80 kN of load. The weight of the rope is 36 kN. The maximum speed is 3 m/s and the acceleration is 1.6 m/s2. The diameter of the wire may be taken as 0.05 d, where d is the diameter of wire rope. The modulus of elasticity of the entire rope is 84,000 MPa. Determine the effective load during acceleration. Express your final answer in kN and use ONE decimal place. Write only the numerical value and do not type the unit anymore.
1. A single-threaded 25-mm power screw is 25-mm in diameter with a pitch of 5mm. A vertical load on the screw reaches a maximum of 5 kN. The co-efficients of friction are 0.06 for the collar and 0.09 for the threads. The frictional diameter of the collar is 45-mm. Find the overall efficiency and the torque to "raise" and “lower" the load.
Q2 / A belt drive consist of two V-belts in parallei, on grooved pulleys of the same size. The angle of the groove is 30". The cross - section area of each belt is 750 mm? and u is 0.12. The density of the belt material is 1.2 Mg/m' and the maximum safe stress in the material is 7 MN/m. Answer the following questions 1- The centrifugal tension in belts is . . (a) increases power transmitted (b) decreases power transmitted (e) have no effect on power transmitted (d) increases power transmitted up to a certain speed and then decreases
The following data is referring to a screw jack. The vertical load on the screw = 20kN Force applied at the lever end whose length = 80cm The mean radius of the screw = 2.5cm Pitch of the screw =1cm Co-efficient of friction between the screw thread and the nut = 0.15 Determine the force on the lever end while raising the load and efficiency of the screw jack
b) the following data is given for the piston of a four-stroke diesel engine: Cylinder bore 300 min Force on piston due to maximum gas pressure = 424 KN Bearing pressure at small end of connecting rod = 15 MPa Length of piston pin in bush of small end = 0.45D Ratio of inner to outer diameter of piston pin = 0.6 Mean diameter of piston boss = 1.4 x outer diameter of piston pin Allowable bending stress for piston pin = 84 N/mm2 %3D Calculate i. Outer diameter and inner diameter of the piston pin ii. Mean diameter of the piston boss; iii. The maximum gas pressures iv. check the design for bending stresses.