40 kN-m B 70 kN VC 2 m 2 m The beam has the following cross section: H 3 m Hinge 18 II 25 III IV 40 kN/m 18 4 m [cm] E 64 An engineer has found a fiber that can be sticked to the top or the bottom fibers to increase the tensile allowable stress from 5 MPa to 50 MPa. Is the fiber necessary? Draw a scheme where you would need the fiber.

40 kN-m B 70 kN VC 2 m 2 m The beam has the following cross section: H 3 m Hinge 18 II 25 III IV 40 kN/m 18 4 m [cm] E 64 An engineer has found a fiber that can be sticked to the top or the bottom fibers to increase the tensile allowable stress from 5 MPa to 50 MPa. Is the fiber necessary? Draw a scheme where you would need the fiber.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 2ETSQ

See similar textbooks

Similar questions

Date: Course: Time: Pind the vertical movement os is 120 KN Stsel Aluminum 3 m Im B P=120 kat Aluminum A = 900 mm² E = 70 GN m² steel A= 600 mm E 200 GNM² %3D
(1) Given A992 steel Ag = 10 in %3D KLy- 80, ry what is $ Pa=? = 60 the' column streugth design
Permissible As in sechion to ensure tensile Compute the design strength of beam shown it 420 MPa , fc = 30 MPa . check the maximum %3D Permissible As in sechion to ensure tensile failure. 4¢25 stimpp10 q00 8432 300 mm
SITUATION 14: A PL 300 x 20 mm is to be connected to two plates of the same material with half the thickness by 25 mm Ø rivets as shown in the figure. The rivet holes have a diameter 2 mm larger than the rivet diameter. The plate is A36 steel with Fy= 250 MPa, allowable tensile stress of 0.60Fy and allowable bearing stress of 1.35Fy. The rivets are A502, Grade 2, hotdriven rivets with allowable shear stress of 150 MPa. 25 mm Ø rivets + + PL 300x20 P/2 P P/2 PL 300x10 43. Which of the following most nearly gives the max. load in kN that can be applied to the connection without exceeding the allowable shear stress in the rivets? a. 675 KN b. 490 KN c. 598 KN d. 790.5 kN 44. Which of the following most nearly gives the max. load in kN that can be applied to the connection without exceeding the allowable bearing stress between the plates and the rivets? a. 490 KN b. 675 KN c. 598 KN d. 790.5 kN 45. Which of the following most nearly gives the max. load in kN that can be applied to the…
STRENGTH OF MATERIAL(SIMPLE STRESS) PLEASE INCLUDE FBD 100% GUARANTEE UPVOTE
The lapbelt assembly is to be subjected to a force of 800N. 800 N 45mm SIMI N What is the required lap length d if the glue can sustain an allowable shear stress of 0.74 MPa?
Determine if W44x285 (A992) section is Compact, Non-Compact or slender. Show neat handwriting and complete solution.
A 15" long rod, pinned at both ends, with radius of 1/2 ", made from 6061 T6 Aluminum is subjected to a compressive axial load of 10 Kips. Question 4 of 6: What is the axial strain in the rod? ( in percent) O .0013 O .13 O 1.3 O 13
In the connection shown, 1/4-in. side and end fillet welds are used to connect the 3-in.-by-1 in. tension member to the plate. The applied load is 60,000 lb. Find the required dimension L. The steel is ASTM A36 and the electrode used is an E70. - Fillet welds L 3" Activate Windows Go to Settings to activate Wir TABLE 19.2 Allowable stresses in ksi (MPa) 12: 12/1 DELL end F12 insert prt sc F10 home F11 F6 F8 F9 F3
Determine the type and magnitude of the stress in a fiber 20 mm from the top of the beam at a section 1 m from the left end of problem number 2 (above problem). choices: 5 MPa, compressive stress 5 MPa, tensile stress 4 MPa, tensile stress 4 MPa, compressive stress
What is the approximate value of the tensile strength governed by yielding of the cross- section of a roof truss diagonal 100 x 75 x 6 mm (fy = 250 MPa) connected to the gusset plate by 4 mm welds as shown in figure? (Take partial safety factor as 1.10) 1 H 100 4 mm weld, 140 mm long 75 A₂ = 1010 mm² Weld 310 mm long
Required information A square yellow-brass bar must not stretch more than 2.4 mm when it is subjected to a tensile load of 34 kN. Given: E= 105 GPa and that the allowable tensile strength is 104 MPa, determine (a) The allowable side length of the cross-section (b) is the allowable value a maximum or a minimum? Why? (c) The allowable length of the bar (d) is the allowable length a maximum or a minimum? (a&b) The allowable side length, for the square cross section, is given as [ (mm) and the value is a (Click to select)