Please round to the nearest One (i.e., 1). PLEASE DO NOT USE COMMA(S) ON YOUR ANSWER!!! Moist unit weight of soil, gamma = 130 pcf Saturated unit weight of soil, gammasat = 140 pcf Cohesion of soil, c = 0 psf The factor of safety, FS = 4 The internal friction angle of soil is 35 degrees B = 3 ft, D₁ = 4 ft, h = 2 ft A square footing is shown below. Determine the followings: Df 67 MAA P A Qali TAF B 1. Ultimate bearing capacity, qu = 2. Allowable bearing capacity, qa = P Unit weight of soil = y Groundwater table Ysat psf $' psf

Please round to the nearest One (i.e., 1). PLEASE DO NOT USE COMMA(S) ON YOUR ANSWER!!! Moist unit weight of soil, gamma = 130 pcf Saturated unit weight of soil, gammasat = 140 pcf Cohesion of soil, c = 0 psf The factor of safety, FS = 4 The internal friction angle of soil is 35 degrees B = 3 ft, D₁ = 4 ft, h = 2 ft A square footing is shown below. Determine the followings: Df 67 MAA P A Qali TAF B 1. Ultimate bearing capacity, qu = 2. Allowable bearing capacity, qa = P Unit weight of soil = y Groundwater table Ysat psf $' psf

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

مکالمات طوارئ ف.. . %07 2:14 quiz.docx -> Soil mechanic /3 rd stage Quiz Q: A soil profile is shown in Figure, plot the variation of o, u, and o' with depth. G, - 2.65 e = 0.5 6. Zone of capillary rise G; = 265; e = 0. Degree of saturation =S = S0 2.5 Ground water table 10 = 42% (moisture content) G, = 2.71 O Sand I saturated clay E Rock ...
Soil sample has a saturated unit wt. of 20kN/m3 and internal friction angle of 30°. Compute the slope angle for a factor of safety of 1.5. Use unit wt. of water as 9.81kN/m3.
2. SPT test was performed at a shallow site composed of uniform granular soil with a unit weight = 20 kN/m³ (shown below are N60). a) Convert to (N1)60. b) Estimate the range of friction angles at depths between 20 and 40 ft. Use various correlations. Compare the differences. SPT N-values (bpf) 10 20 30 40 50 10 Silty Sand (SM): Piedmont Residuum 30 40 50 60 Depth (feet)
Q- What will be the time required (in minute) in falling the head from 45 cm to 30 cm in a variable head permeability test, if the coefficient of permeability of the soil is known to be 6.89 x 106 m/sec. The length and cross-sectional area of the soil sample is 60 cm and 210 cm² respectively. The area of stand pipe is 6.5 cm².
A triaxial test on a saturated soil has the ff. results:a. Determine the drained angle of friction and cohesion of the soil. b. Determine the undrained angle of friction and cohesion of the soil. Please answer this asap. For upvote. Thank you very much
The SQUARE base permeameter (seen from above), has three soil layers arranged vertically as shown in the image. L is: 70cm, the difference of head h is: 105 cm. The coefficient of permeability of soil 1 K1 is 0.065 cm/sec, soil 2 K2 is 0.0030 cm/sec and soil 3 K3 is the 0.0095 Calculate the amount of water collected in a time of 10 minutes.
A balloon type apparatus is sued to determine an in-place unit weight for a soil. The volume of the test hole determined by reading the water level graduations on the apparatus cylinder before and after digging the test hole is 0.000708 m3. The weight of the soil obtained from test hole is 1410 g. The soil sample was dries on a tield stone and weighs 1237 g. (a.) Compute the water content (5 points). (b.) Compute the in-place dry unit weight of the tested soil in kN/m3. (5 points) (c.) Determine the percentage of compaction for the test result if the soil is part of a compacted earth fill whose maximum unit weight obtained from the laboratory compaction tests) is 18.57 kN/m3.
H.W 5 (1+ we' |Yw• For a saturated soil, show that: Ysat Soil Mechanics
Q1 along points A,B,C,D 5m A 5m Soil A 5m Soil B 2m 3m 3m Datum I kA = 10 kg
1. From the video, the following data were obtained. a. Mass of SSD Sand = 505.0g b. Mass of pycnometer with water only = 679.0g c. Mass of pycnometer with sand and water = d. Mass of dry sand (Not show in the video) = 491.0g %3D = 952.0g Calculate the specific gravity values (dry and SSD condition) 2. The specific gravity and absorption test (ASTM C128) was performed on fine aggregates and the following data were obtained. a. Mass of SSD Sand = 500.0g b. Mass of pycnometer with water only = 623.og c. Mass of pycnometer with sand and water = d. Mass of Dry Sand = 495-5g %3D 938.2g %3D Calculate the specific gravity values (dry and SSD).
1. The soil has a friction angle of 25°. Assuming there is no chart given, determine the following: a.Nc: b.Nq: c.Ny:
A balloon type apparatus is sued to determine an in-place unit weight for a soil. The volume of the test hole determined by reading the water level graduations on the apparatus cylinder before and after digging the test hole is 0.000708 m3. The weight of the soil obtained from test hole is 1410 g. The soil sample was dries on a tield stone and weighs 1237 g. (a.) Compute the water content. (b.) Compute the in-place dry unit weight of the tested soil in kN/m3. (c.) Determine the percentage of compaction for the test result if the soil is part of a compacted earth fill whose maximum unit weight obtained from the laboratory compaction tests) is 18.57 kN/m3.