2. A 400KN block is resting on a rough horizontal surface for which the coefficient of friction is 0.40. Which of the following most nearly gives the force P required to cause motion to impend if applied to the block downward at 30degrees with the horizontal. A. 150KN B. 160KN C. 240kN D. 300KN

2. A 400KN block is resting on a rough horizontal surface for which the coefficient of friction is 0.40. Which of the following most nearly gives the force P required to cause motion to impend if applied to the block downward at 30degrees with the horizontal. A. 150KN B. 160KN C. 240kN D. 300KN

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Related questions

Q: A lever AB of negligible weight is loosely fitted onto a 2.5-in.-diameter fixed shaft. Knowing that…

A: Given data: Diameter of fixed shaft, d = 2.5 in. Coefficient of friction between fixed shaft and…

Q: 4. The position of the machine block B is adjusted by moving the wedge A. Knowing that the…

Q: A block weighing 800 N is acted upon by a force P as shown. Knowing that the coefficient of friction…

Q: The 50-lb block A and the 25-lb block B are supported by an incline that is held in the position…

A: Given Block A mass = 50 lb Block B mass = 25 lb Friction between two blocks µ1 = 0.15 Friction…

Q: The wheel A and a block B are connected by a cable. The coefficient of friction of the wheel and the…

Q: A lever AB of negligible weight is loosely fitted onto a 2.5-in.-diameter fixed shaft. Knowing that…

A: Free-body diagram shaft-lever arrangement is given as, The friction-gap is written as,

Q: Blocks A and B Weigh 50 Nand 30 N respectivety using the coefficients of Static friction indicated.…

A: Find largest weight of body D.

Q: A lever AB of negligible weight is loosely fitted onto a 2.5-in.-diameter fixed shaft. Knowing that…

A: The radius of shaft r = 2.5/2 inch = 1.25 in. The coefficient of static friction is μs = 0.15 N The…

Q: A block with mass (3 kg) is pl a) What coefficient of friction b) If the coefficient of friction i…

Q: . The minimum value of P that will hold the block in place if θ is zero is nearest to? b. The…

Q: A block with weight W is pulled up a plane forming an angle a with the horizontal by a force P…

Q: A trolley weighing W₁= 306.1725 N, a crate with Wc= 612.345 N, is being transported along a smooth…

Q: The coefficient of friction for all contact surfaces is 0.15. The weight of blocks A and B are 250 N…

A: Given dataCoefficient of friction for all contact surfaces μ = 0.15Weight of the block A WA =…

Q: The friction tongs shown in Figure are used to lift a 350 kg casting. Knowing that h = 864 mm,…

A: Given Data:- M = 350 kg H = 864 mm Find:- Smallest allowable friction coefficient M = ?…

Q: 1. A hawser (a thick docking rope) thrown from a ship to a pier is wrapped two full urns around a…

A: Given:T2=7500 NT1=150 N

Q: C- In Fig.C, the cylinder shown is of weight W and radius r, and the coefficient of static friction…

Q: Problem 2.11 As shown in Fig. 2.23, consider a block that weighs W. Due to the effect of gravity,…

A: We are suppose to solve only one question. Please post other question as a separate question. Please…

Q: A 20 kg block is held in place on an incline plane as shown by a rope that passes over a…

Q: Two 10° wedges of negligible weight are used to move and position the 400-lb block. Knowing that the…

A: Given data Coefficient of static friction between the surfaces = 0.25 Weight of the block W = 400lb…

Q: The block and tackle shown are used to lower a 150-lb load. Each of the 3-in.-diameter pulleys…

A: Given, Considering Free Body diagram of First Pulley BC As friction is present between the pulley…

Q: A 15° wedge is forced under a 50-kg pipe as shown. Knowing that the coefficient of static friction…

A: Given: The wedge angle, θ = 15⁰ The mass of the pipe, m = 50 kg The coefficient of static friction…

Q: A car has a mass of 1.5 tons and a centre of gravity at point G. The coefficient of friction between…

A: GIVEN: TO FIND:

Q: A 1.2-m plank with a mass of 3 kg rests on two joists. Knowing that the coefficient of static…

A: Given data: Mass of the plank, m = 3 kg Coefficient of friction, μ = 0.3 Let, g = acceleration due…

Q: A horizontal force of 200 lb is required to push an 800-lb piano across a level carpeted floor. The…

A: Given that, Horizontal Force, Fh=200 lbWeight of piano, Wp=800 lbDiamter of wheel, d=2 in The load…

Q: An 800 N-m couple is applied to the flywheel as shown. The coefficient of belt friction is 0.20. The…

A: (a) Since the moment is in anti-clockwise direction, the rope is stretched that is attached to the…

Q: Determine the maximum allowable value of weight W at rest. Knowing that the coefficient of static…

Q: For any machine, as the friction of the moving parts increase: (a) the AMA and the % efficiency…

A: Given: To find the correct option.

Q: The static coefficient of friction is smaller than the kinetic coefficient of friction. الاختيارات…

A: Ans) : False Because static coefficient of friction is greater than the kinetic coefficient of…

Q: QI-A 75-Kg man wants to pull a 145- Kg box and the coefficient of static friction between the box…

Q: Two 10° wedges of negligible weight are used to move and position the 400-lb block. Knowing that the…

Q: A lever AB of negligible weight is loosely fitted onto a 2.5-in.-diameter fixed shaft. Knowing that…

A: Given: The diameter of the shaft, d = 2.5 in The coefficient of friction between shaft and lever, μ…

Q: 4. The position of the machine block B is adjusted by moving the wedge A. Knowing that the…

A: A) Raising the Machine: f1 = μN1 = 0.35N1 f2 = μN2 = 0.35N2 Applying the Equilibrium Equations…

Q: Blocks A and B are held in place in a plane inclined at an angle 8. Block B, located 1m from the…

Q: 1. Determine the maximum allowable value of weight W at rest. Knowing that the coefficient of static…

Q: A wedge A of negligible weight is to be driven between two 100 lb. block B and C resting on a…

A: Given: The weight of block B and block C is, W=100 lb. The coefficient of static friction between…

Q: The direction of impending motion of the block if force P is at its minimum and maximum of?

Q: A 10° wedge is used to split a section of a log. The coefficient of static friction between the…

A: Given data as per the question The angle of wedge =100 coefficient of static friction between the…

Q: On a ladder resting on smooth ground and leaning against vertical wall, the force of friction will…

A: As per our company guidelines, we are supposed to answer only the first 3 part 1) If a ladder is…

Q: Two cylinders are connected by a rope that passes over two fixed rods as shown. Knowing that for…

A: Given data as per question m = 20 kg Mass of block A =50 kg

Q: a 1.2-m plank with a mass of 3kg rests on two joists. knowing that the coefficient of static…

Q: The crate pulled by a man as shown weighs 200 N. Supposed that the static friction coefficient…

A: Static equations:

Q: A flat belt is used to transmit a couple from pulley A to pulley B . The radius of each pulley is 50…

Q: A 20 kg square block made of material A is place on a horizontal plane B. A push of 150N…

A: When there is relative motion between any two surfaces, there must be a resisting force which is…

Q: An 800 N-m couple is applied to the flywheel as shown. The coefficient of belt friction is 0.20. The…

A: Since there is friction present in the belt, thus the tensions in the belt at point A and B will not…

Q: The block and tackle shown are used to raise a 150-lb load. Each of the 3-in.-diameter pulleys…

A: According to principle of Kinematics, The total Upward and Downward forces are zero.

Q: In the given figure, W= 200kg. Assume that the coefficient of friction between surfaces is 0.40.…

Q: A 12° wedge is used to spread a split ring. The coefficient of static friction between the wedge and…

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

2. A 400KN block is resting on a rough
horizontal surface for which the
coefficient of friction is 0.40. Which of
the following most nearly gives the
force P required to cause motion to
impend if applied to the block
downward at 30degrees with the
horizontal.
A. 150kN
B. 160kN
C. 240KN
D. 300KN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

a 46 l Asiacell B/s DRAW F. B. DAND SHOWTHE DIRECTION OF FRICTION FORCE 40 kN 60 kN VEMATHalino.com
A 2000-lb bike with a rear wheel drive has awheelbase of 10 ft. The c.g. is 3 ft above thepavement and 4 ft ahead of the rear wheels.The coefficient of friction is 0.60 between thetires and the pavement. Determine the accelerating horizontalforce on the motorcycle when theacceleration is maximum.a. 1646.57 lbs b. 1475.66 lbsc. 1664.75 lbs d. 1466.75 lbs
5. A force acting on a block causes it to slip , if the frictional force is equal to 66% of the max. friction force and the static coeff. of fric on is 0.3, the kinetic coeff. of friction is--- A. 0.25 B. 0.2 C. 0.45 D. 0.4
The 300N block rests upon a level plane for which the fk is 0.20. A force P = 100N, directed at 30° from the horizontal pulls the block and moves 80m starting from rest. If the 100N force is then removed, how much further will it travel? a. none b. 48.803m c. 40.078m d. 47.800m 3. 40.780m
Which of the following does the frictional forces depend on: 1- Smoothness of the surface 2- Normal force O a. only 1 O b. neither 1 nor 2 Oc. only 2 O d. both 1 and 2 APP
Q3: As shown in figure, find that at what distance body A will attain a velocity of 3 m/s from A 2000 N when starts rest. Assume coefficient of friction as 0.2 for block and and pulleys frictionless and weightless. surface are 3) DOM www N 00
The block shown in the following figure has a weight W equals to 75 lb and subjected to the action of a force of 30 lb. The coefficient of static friction between the block and the ground is equal to 0.25. If the angle 0 is equal to 30, the friction force between the block and the ground is. H =0.25 H =0.20 m 30 lb Select one: а. 25.245-lb O b. 10-lb O c. 15-lb O d. 20-lb
15. A 4,900N block is resting on a 30° inclined plane with a coeff of friction of 0.30. What is the required horizontal force P that prevents the block from sliding? a. 1,017N c. 4,236N b. 1,158N d. 5,212N
A 25kg crate resting on a horizontal surface is pushed as shown. If a force of 99N is required to move the crate, the coefficient of static friction (u) between the crate and the floor is O a. 0.4041 O b. 2475.00 Dc. 24255.00 d. 3.96 :ir ENG 40) A ^A T/TE DELL
A box of weight 100 N is affected by F force, with an inclination of 30° with the horizontal. If the coefficient of friction between the box and the surface is 0.4, and the box is moving with an acceleration of 20 m/s?. Fin the minimum force (F) act on the box. F=? 2300 а. 235.22 N O b. 322.38 N С. 228.7 N O d. 222 N
A 150lb man stands on a 60lb bar to which a cable is fixed at B. The cable passes over two fixed pegs with coefficients of friction indicated. Assume that the arrangement of the pegs permits the cable to contact each peg over a total angle of 90-degrees (90-degrees per peg). Assume that the normal force exerted by the man on the bar acts downward through A. Find the largest force the man can exert on the cable and maintain the bar horizontal.
The height of the g point is 0.5m, the distance of the rear wheel to theg point is 1.75m, the distance of the front wheel to the g point is 1.8 m, and the car with a mass of 2100kg brakes suddenly while moving at 24v speed. l-Find the friction coefficient between the wheel and the road? 2-Find the way the vehicle takes until it stops?