A box of weight 100 N is affected by F force, with an inclination of 30° with the horizontal. If the coefficient of friction between the box and the surface is 0.4, and the box is moving with an acceleration of 20 m/s?. Fin the minimum force (F) act on the box. F=? 2300 a. 235.22 N O b. 322.38 N O c. 228.7 N d. 222 N

A box of weight 100 N is affected by F force, with an inclination of 30° with the horizontal. If the coefficient of friction between the box and the surface is 0.4, and the box is moving with an acceleration of 20 m/s?. Fin the minimum force (F) act on the box. F=? 2300 a. 235.22 N O b. 322.38 N O c. 228.7 N d. 222 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5- (Work, Energy) The block M in Fig (a) weighs 500N and has a downward velocity of 5 m/s at the instant the force P=1 kN is applied. The coefficient of friction between the arm AB and the rotating body is 0,4. The rotating body weighs 800 N and has a centroidal radius of gyration of 50 cm. Find the distance the weight travels before coming to rest. 30cm | 60cm 30ст B W M S0cm ||
(b) A body of mass m moves along y such that at timet its position is y(t) = at/2 - bt + c, where a, b, c are constants. %3D i. Calculate the acceleration of the body. ii. What is the force acting on it?
Q.6 A body of weight 120N rest on a rough horizontal surface (µ = 0.3) and is pulled by a force applied at an any of 30° to the horizontal. The force (in N) required to just cause body to slide over surface about is A 22.5 B в 27 WRONG C 35.43 D 40
4. A mass m is on a frictionless table and is attached to the wall by a massless spring (spring constant k). The air friction on the block is f=-2ßmv. During an earthquake, the wall moves left and right as y(t) = B cos w t. y(t)=Bcos m t www m x(t)=? (a) Show that the eqn. of motion for m is * + 2ßx + w¿x = f cos wt with wo = %3D т Express fin terms of B and wo. (b) Derive the amplitude of the m oscillation. (c) What is the amplitude at the resonance frequency w = wo?
1,V 3 46| Asiacell K/s the system blocks shown below is in equilibrium, the weight of block A is 10 kN and for block B is 35 kN . The coefficient of friction between A and surface is 0.2 and between two block :A and B is 0.15. Answer the following P=40KN الخيار رقم 1 5 نقاط The direction of friction force between two blocks which * effect on block A is in First Quarter Second Quarter Third Quarter Fourth Quarter
pls send me answer of this question all the parts pls and i will rate you sure, pls solve a,b,c and d and also a and b A 200-kg dragster (racing car) exerts a constant force of 4000 N during a race. The coefficient of kinetic friction between the tires and the pavement is .15. If the drag strip is 1000 m long, determine:a. The net force on the dragster. b. The acceleration of the dragster. c. The time it takes for the dragster to finish the race.d. The dragster's velocity at the end of the race.The dragster now needs to slow down, so it opens a parachute. The force of air drag is 3500 N. The driver also locks the brakes of the dragster, and the coefficient of kinetic friction becomes .75. Determine:a. How long it will take to stop the dragster.b. The distance the dragster travels while stopping.
Three friends ride a Ferris wheel with a diameter of 76m. Their combined mass with each car of the Ferris wheel is 389kg. When their car is at position A, the steel support applies 503N force at the car at an angle of 40degrees with the horizontal. What is the speed of the cars?
The mass of the flat belt is 0.6kg/m and the tension on the tight side of the belt is 1.7kN the coefficient of friction between the belt and the pulley is 0.2 and the angular speed N of the belt is 400rpm.Angle of lap fita and the diameter D of the pulley 150°and 50cm respectively.with the addition of centrifugal tension Design the belt drive by determine velocity belt centrifugal tension tension on the slack side of the belt power transmitted at this speed in kilowatts maximum power delivered
The two identical springs below are holding up the mass D. The springs each have a stiffness of 895 N/m. The mass of D is 18.8 kg. What was the unstretched length of the springs in m? A 45° D 45 C B 0.3 m
Consider a conical pendulum with a mass m = 10 kg on a string of length L= 5 m. The angle it makes with the vertical is 4°. The pendulum is place on the surface of Mars. The velocity of the mass is given by v=Lgsin Otan ở What should be the length of the string if the pendulum has the same speed as the one on the Earth? Assume the angle is kept the same. ( 9mas=3.71 m/s 14 - O A) 1.9 m O B) 5 m O C) 13.2 m O D) 1.4 m O E) 3.6 m
The mass of the belt is 0.6kg/m and the tension on the tight side of the belt is 1.7kN.the coefficient of friction between the belt and the pulley is 0.2 and the angular speed N, of the belt is 400rpm.Angle of lap fita and the diameter D of the pulley are 150° and 50cm respectively.with the addition of centrifugal tension, Design the belt drive by determine (A) velocity of the belt (B) centrifugal tension (C) tension on the slack side of the belt (D) power transmitted at this speed in kilowatts (E) maximum
Q3. As shown on the right in image below, the force Facting on the box varies with displacement s, and the coefficient in the image, C = 14. Determine the work done by force Fto the box when the box has displaced s = 1.9 m. Please pay attention: the numbers may change since they are randomized. Negative sign must be included if the work done is negative. Your answer must include 2 places after the decimal point, and proper SI unit. F (N) F 5 3 S 4 C s (m) 1 2