You need the shear modulus for a particular material in order to calculate shear strain for a known applied shear shear stress. You can't find shear modulus for the material, but you can find elastic modulus (200 GPa) and Poisson's ratio (0.3). Which of the following could you use as the shear moduluc for vour calculations2

You need the shear modulus for a particular material in order to calculate shear strain for a known applied shear shear stress. You can't find shear modulus for the material, but you can find elastic modulus (200 GPa) and Poisson's ratio (0.3). Which of the following could you use as the shear moduluc for vour calculations2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Given a stress state of ø, = -4 MPa, øy = 12 MPa, ty = 7 MPa ccw 1) Draw a properly oriented stress element illustrating this state of stress 2) Using Mohr's circle, find the principal stresses and directions, and show these on a stress element correctly aligned with respect to the xy coordinates. Draw another stress element to show zi and 72, find the corresponding normal stresses, and label the drawing completely. 3) Use the plane-stress transformation equations to validate your answers in part 2
The nodal coordinates and the nodal displacements for some plane stress elastic element is listed in the following problem. The element is 0.1 m thick. The coordinates and displacements are given in meters. (a) Calculate K(1,1) of the element stiffness matrix (b) Calculate the element stress [16 D = 106| 4 4 01 16 0 (N/m²) 61 1 N1 = (a1 + bịx+ Cy) 2A 1 N2 = 2A -(a2 + b2x + c2y) 1 Na = (az + bzx + C3y) 2A b1 = y2 - y3 a1 = X2y3 - X3y2 a2 = X3y1 - X1y3 C1 = X3 – X2 C2 = X1 – X3 C3 = X2 - X1 b2 = y3 - Yı az = X1y2 - X2y1 b3 = y1 - Y2 X1 = 2 X2 = 1 X3 = 1 y2 = 1 v2 = 0.001 Y1 = 2 Y3 = 0 U1 = 0.003 Uz = 0.0015 V1 = 0 v2 = -0.003 v3 = 0.0
The figure shows the stress-strain curve for a rectangular steel test piece in tension. The test piece is loaded up to point B and then released. If the test piece was originally 58.9 mm long, estimate its new length (in mm) after it is released? State your answer in mm without including the units. Stress (MPа) Elastic Inclastic strain strain 473 - В 408 - 340 272 - Unload 204 - Reload 136 - Plastic Elastic 68 - deformation recovery 0.0020 0.0060 0.0100 0.0000 0.0040 0.0080 0.0120 Strain (mm/mm) Answer:
The graph shown below shows the Modulus of Elasticity (E) of different materials with respect to temperature (°C). 240 210 170 140 100 -Carbon Steel, C < 0.3% -Nickel Steels, Ni 2% - 9% 70 Cr-Mo Steels, Cr 2%-3% Copper -Leaded Ni-Bronze -Nickel Alloys - Monel 400 35 -Titanium rengineeringtoolbox.com -Aluminium -300 -200 -100 100 300 400 500 600 700 800 Temperature (degc) a) Which material is the most ductile with increasing temperature? b) Which material is the least ductile with increasing temperature? c) Discuss the change in ductility (brittle / ductile behavior) occurring for different materials. Also, comment on why Young's modulus changes with temperature. E-modulus of elasticity (GPa)
A circular pipe of internal diameter 30 mm and thickness 4 mm is subjected to a force 30 kN and the elongation was measured as 1 mm. If the length of the pipe is 2 m, find the value of Young's modulus of elasticity and the stress in the pipe. Match each item to a choice: Young's Modulus (GPa) Stress (MPa): Choices: : 140.4 # 47.9 B 56.4 # 120.8 #240.8 8 70.2
Which of the following is the unit for electrical conductivity? Select one: O (Q-m) -1 O (Q-mm) O m/S O Q-m In a stress strain curve of mild steel, the elastic limit will be before the limit of propor ype here to search 99+ hp fs 米 f5 f6 f7 1- f8 fg & 7 V 3 6. 8. 9/6 4+ %24 %23
A copper rod [E= 113 GPa] originally 606 mm long is pulled in tension with a normal stress of 242 MPa. If the deformation is entirely elastic, what is the resulting elongation (in mm)? Note: Do not include units in your answer Answer: mage Next page rnonline.gmit.ie/mod/quiz/attempt.php?attempt=5462898.cmid-4251738page.. S°C ostly sloudy ecolutions BICVelleda BIC Velleda. MARKER WHITEBOARD
Find the force pneed to fill the gap. Young's modulus as 300 GPa C 1,5 cm² 2 cm2 P. A 1 cm 1/2 p 0.5 m 0.5 m 1 m 0.5 mm (a) 13.84KN. (b) 14.21KN.
The plane stress displacement field for the pure bending problem was given by u = - El v = (vy? + x² - P), where -1
The flow stress (in MPa) of a material is given by o = 500 0.1, Where & is true strain. The Young's modulus of elasticity of the mater 41 is 200GPa. A block or thickness 100 mm made of this material is compressed to 95 mm thickness and then the load is removed. The final dimension of the block (in mm) is
The following stress condition is applied to a cubic material. Normal stress in the x direction is 15 Mpa, normal stress in the z direction is -7 Mpa and the shear stress in the x-z plane is 59 Mpa (a) Write the stress tensor (b) Find the maximum normal stress (c) Find the angle with respect to the x-axis at which the maximum normal stress is applied (d) Find the maximum shear stress (e) Determine the angle with respect to the x-axis at which the maximum shear stress is experienced
400 350 300 250 200 150 100 50 0.002 0.004 0.006 0.008 0.01 Strain Stress (MPa)