Please don't provide handwritten solution.... Water shoots out of a large tank sitting on a cart with frictionless wheels. The water jet velocity is Vj = 7.00 m/s, its cross-sectional area is Aj-26 mm2, and the momentum flux correction factor of the jet is 1.04. The water is deflected 135° asshown (8= 45°), and all of the water flows back into the tank. The density of the water is 1000 kg/m³. Calculate the horizontalforce F (in units of N) required to hold the cart in place.TankVACartThe horizontal force required to hold the cart in its place isN.

To calculate the horizontal force required to hold the cart in place, we can use the following…

Water shoots out of a large tank sitting on a cart with frictionless wheels. The water jet velocity is Vj = 7.00 m/s, its cross- sectional area is Aj= 26 mm2, and the momentum flux correction factor of the jet is 1.04. The water is deflected 135º as shown (8= 45°), and all of the water flows back into the tank. The density of the water is 1000 kg/m³. Calculate the horizontal force F(in units of N) required to hold the cart in place. Tank V₂ Ap Cart The horizontal force required to hold the cart in its place is N.

Water shoots out of a large tank sitting on a cart with frictionless wheels. The water jet velocity is Vj = 7.00 m/s, its cross- sectional area is Aj= 26 mm2, and the momentum flux correction factor of the jet is 1.04. The water is deflected 135º as shown (8= 45°), and all of the water flows back into the tank. The density of the water is 1000 kg/m³. Calculate the horizontal force F(in units of N) required to hold the cart in place. Tank V₂ Ap Cart The horizontal force required to hold the cart in its place is N.

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter8: Momentum And Collisions

Section: Chapter Questions

Problem 51P

See similar textbooks

Similar questions

An airplane has wings, each with area 3.85 m2, designed so that air flows over the top of the wing at 248 m/s and underneath the wing at 226 m/s. Approximately what size wings would an aircraft need on Mars if its engine generates the same differences in speed as in the "Practice It" and the total mass of the craft is 300 kg? The density of air on the surface of Mars is approximately one percent Earth's density at sea level, and the acceleration of gravity on the surface of Mars is about 3.8 m/s2. ______________m2
A 2.5-cm-diameter horizontal water jet with a speed of Vj = 40 m/s relative to the ground is deflected by a 60° stationary cone whose base diameter is 25 cm. Water velocity along the cone varies linearly from zero at the cone surface to the incoming jet speed of 40 m/s at the free surface. Disregarding the effect of gravity and the shear forces, determine the horizontal force F needed to hold the cone stationary.
A container has a hole with a diameter of 1.8 cm^2 at the bottom. Through the hole goes 280 cm^3 of water every second out. At what hight does the water settle over time? What is the velocity of the jet through the hole at the bottom of the container at that moment? (The solution is 12 cm and 1.6 m/s)
In testing a new material for shielding spacecraft, 126 small ball bearings, each moving ata supersonic speed of 410.1 m/s, collide headon and elastically with the material during a0.803 min interval.If the bearings each have a mass of 7.6 gand the area of the tested material is 0.77 m2,what pressure is exerted on the material?Answer in units of Pa.
Water is ejected from the water nozzle with a speed vo = 47.9 ft/sec. For what value of the angle e will the water land closest to the wall after clearing the top? Neglect the effects of wall thickness and air resistance. What distance x to the right of point B does the water land? 4.5' 72.0' B 64' Not to scale Answer: i X = i ft
A high-carbon steel with a fully pearlitic microstructure was used to form a high-strength bolt (H.-C. Lee et al., J. Mater. Proc. Tech. 211, 1044 (2011)). It was found that the bolt head had an average interlamellar spacing of 257 nm whereas the average spacing in the body of the bolt was 134 nm. Assuming that dislocation pileup is the primary mechanism responsible for the strength of this alloy, what ratio of strength (or hardness) might be expected in the head and body of the bolt?
Find the center of mass of a laminate bounded by y=−x,y=x,y=2 with variable density modeled by \rho (x,y)=y+5. Question 3 Answer a. (0,2619) b. (35,94) c. (−23,116) d. None of the above e. (0,1) f. (0,32)
In a water pistol, a piston drives water through a larger tube of radius 1.00 cm into a smaller tube of radius 1.00 mm as in Figure P9.41. (a) If the pistol is fired horizontally at a height of 1.50 m, use ballistics to determine the time it takes water to travel from the nozzle to the ground. (Neglect air resistance and assume atmospheric pressure is 1.00 atm.) (b) If the range of the stream is to be 8.00 m, with what speed must the stream leave the nozzle? (c) Given the areas of the nozzle and cylinder, use the equation of continuity to calculate the speed at which the plunger must be moved.(d) What is the pressure at the nozzle? (e) Use Bernoulli’s equation to find the pressure needed in the larger cylinder. Can gravity terms be neglected? (f ) Calculate the force that must be exerted on the trigger to achieve the desired range. (The force that must be exerted is due to pressure over and above atmospheric pressure.)
Global warming is a cause for concern because even small changes in the Earth’s temperature can have significant consequences. For example, if the Earth’s polar ice caps were to melt entirely, the resulting additional water in the oceans would flood many coastal areas. Model the polar ice as havingmass 2.30 × 1019 kg and forming two flat disks of radius 6.00 × 105 m. Assume the water spreads into an unbroken thin, spherical shell after it melts. Calculate the resulting change in the duration of one day both in seconds and as a percentage.
A garden hose with an internal diameter of 1.9 cm isconnected to a (stationary) lawn sprinkler that consists merely ofa container with 24 holes, each 0.13 cm in diameter. If the waterin the hose has a speed of 0.91 m/s, at what speed does it leave thesprinkler holes?
A rain gauge consists of a funnel with a diameter D = 10 cm that collects rain and deposits liquid water of density ρ = 1 × 103 kg / m^3 inside a cylinder of diameter d = 1 cm. The column of collected liquid rises at the rate of one centimeter per minute. a) If the raindrops fall into the funnel with a velocity of 10 m / s, calculate the mass of water liquid in a cubic meter of the atmosphere. b) Assuming that the raindrops have a radius of 1 mm, determine the number of drops in a cubic meter of the atmosphere. Justify your calculation method.
Q6/ Air at a density of 0.9 kg/m³ enters the intake (control face 1) of a car engine with a diameter of 0.2m at an absolute velocity of 50 km/hr (relative to the earth), as illustrated in Figure. The exhaust at a density of 0.5 kg/m3 leaves the tail of the car engine (control face 2) with a diameter of 0.1 m. The car (engine) (control volume) is traveling at an absolute velocity of 30 km/hr (relative to the earth). (a) Determine the velocity of the flow at control face 1 relative to the control volume, v1. (b) Determine the mass flow rate through the car engine. (c) Determine the absolute velocity of the flow at control face 2, v2 (abs). (d) Determine the velocity of the flow at control face 2 relative to the control volume, v2. te 50 km/he A-09 kg/m D, -02 m Control volume D-01 m Intake Exhaust Po Var=30 km/hr )חח