WQ2⇒8rho70DzDzA first-order system in control. If thedischarge time of D1 is 6, using AnalogComputer Technique, find the input plotand the output plot and find the equation.0-45ho4.-Xdy = 0:45 - √hodt

Answered: Image /qna-images/answer/b6170d6e-9d7e-47fd-8ff7-ec4e1b304214.jpg

Answered: W Q2 ⇒8r ho 70 Dz Dz A first-order…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What will be the controller output for a Proportional Derivative controller (i) Initially and (ii) after T= 2 seconds (iii) after T= 3 seconds after the error begins to change from zero at the rate of 2%/s. The controller has Kp=2.5,KD=1.4 seconds. 9. S. 7- 3. 1 Time % of Error 61
Part 2: The serial data-input waveform (Data in) and data-select inputs (S0 and S1) are shown in Figure_5. Determine the data-output waveforms from DO through D3. Data In so s1 Figure_5
Q2. It is required to design a sequence detector that detects overlapped occurrences of the sequence 10010. The circuit receives a serial input X and produces a serial output Z. The output Z will be 1 when the circuit detects the sequence 10010. Assume the existence of a reset input to reset the machine to a reset state. Draw the state diagram of the circuit assuming a Moore model. The following is an example of some input and output streams: Input X 0010010010 1 0 0 1 00 Output 0000 0 0 010010 00 0 1
2)Convert 11011010100100012 to hexadecimal. A)895B B)CA11 C)53AC1 D)DA91
The serial data input waveform (Data in) and Data select lines (S1 and S2) of 1:4 demultiplexer are shown in the figure. Determine the output waveforms on D0, D1, D2 and D3. 0 I2 3 4 5 6 7 Data in LSB S,! MSB S2 Do D D2 D3
Draw the state diagram for a Modulo-6 synchronous counter which follows the count sequence000, 010, 011, 001, 100, 110, 000, 010, … . Show all possible states including the ones that are notdesired. The undesired states should be depicted to be transiting to any of the desired states.Choose the 000 state for this purpose. It is important to include the undesired states to ensure that,if the counter accidentally gets into any of these undesired states owing to noise or power-up, thecounter will go to a desired state to resume the correct sequence on application of the next clockpulse.
Q2) determine A>B, A
Part 4: The data-input and data-select waveforms in Figure 7 are applied to the multiplexer. Determine the output waveform F in relation to the inputs. DO D1 D2 D3 1. so s1 Figure_7
Initially all outputs were RESETE.. Then the input (which is given in the figure) is applied. What is the output value (Q3,Q2,Q1,Q0) after 3 clock signals. MSB Qo Q MSB 1101 D D D. D Output 14 - > CLK D CLK D CLK > CLK FLALEL CLK O A 1101 O B 1011 O 9 1110 O D 0110 O E 0101
Convert the octal NUMBER 1004. 2435 to hexadecimal number showing the steps
Design an encoding matrix with diodes and resistors to display a decimal number to on the seven-segment display. You have 10 switches (WO-W9) with one terminal connected to Vec. For decimal number 0, switch 0 (S0) is closed, for decimal number 1, switch 1 (S1) is closed etc. (Switches are on the vertical axis, S0 on top and the outputs are taken on the horizontal axis (Y0-Y6), with “a" on the left and "g" on the right. Note that (Y0-Y6) outputs are used as inputs to seven-segment display. Since these outputs cannot drive the seven segment display LEDS you may need additional bipolar transistors and resistors. The supply voltage is 5V and each LED needs a current of 20mA. Note that this is a design problem and the design is not unique. Do your best! f a a e
A circuit has apushbuttonswitch connected to pin PB2 and an LED to pin PC0 of AVR ATmega16 microcontroller. Write a program to control the LED as when the pushbutton pressedthe LED will blink five times with 800ms total delay time for every blink.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

W Q2 ⇒8r ho 70 Dz Dz A first-order system in control. If the discharge time of D1 is 6, using Analog Computer Technique, find the input plot and the output plot and find the equation. 0-45 ho 4. -X dy = 0:45 - √ho dt