Two cylindrical parts are to be assembled to make an interference fit. The nominal diameter of the assembly is 100 mm. Before assembly, the inner member (copper) has an outer radius that is 0.2 mm larger than the inner radius of the outer member (aluminum). If there is no other force acting on the assembly, determine the maximum and minimum principal stress in both the members. Assume Poisson's ratio of 0.3 for both the materials. Also take rj = 30 mm for copper cylinder and ro = 80 mm for aluminum cylinder

Q: In the Brinell hardness test, if the load used 1200 kg, and the ball diameter 6 mm, write down the…

A: Given details: P=1200kgD=6mmBHN=586 formula used: BHN=2PπDD-D2-d2

Q: Required information The part shown is loaded at point Cwith 310 N in the positive y direction and…

A:

Q: ut of (a). Briefly explain THREE (3) sources of internal residual stresses in metal components and…

A: Dear student, we are suppose to solve only one question. Please post other question as a separate…

Q: 1. A bar is subjected to a tensile stress of 100 MPa, Determine the normal and tangential stresses…

A: Givenσ=100Mpaθ=30o

Q: Required information The part shown is loaded at point C with 290 N in the positive x direction and…

A: Given: The load at C, P = 290 N The load at E, Q = 200 N The diameter of the pipe, d = 12 mm

Q: A pipe has an outside diameter of 0.7 inches and inside diameter of 0.12 inches. A force of 144 lbs…

A:

Q: For a stress level of 240 MPa compute the maximum stable radius of a semicircular surface flaw in…

A: Consider the table shown below for the stress intensity factor and yield strength for the different…

Q: Compare between the hardness profile for the following cases, in the radial and longitudinal section…

A: Hardness - Longitudinal distance

Q: 13.9 (8) A thick cylinder has an internal diameter of 75 mm and an external diameter of 125 mm. The…

A:

Q: A cylindrical boiler with an inside diameter of 2.5 m and a wall thickness of 40 mm is made of a…

A: GIVEN DATA- Pressure P=1.5MPa Internal Dia d=2.5m = 2.5*1000=2500mm Thickness t=40mm Yield stress…

Q: A cylinder head stud has a diameter of 14mm at the bottom of the thread. If the maximum tensile…

A: Given data: The diameter of the stud, d = 14 mm. The maximum tensile stress, σ=30 MPa. Write the…

Q: Describe the Maximum Normal Stress Theory?

A: The Maximum Stress Theory is one of the failure theories postulated by Rankine. Hence this theory is…

Q: ure 1 shows a compound bar with three different diameters, d1-9mm, d2-22mm, and d3-14mm machined…

A:

Q: Give an example of complicated stress?

A: Stress: When a body is subjected to a force/load, it develops an internal reaction in order to…

Q: Besides normal tensile stress, list three other types of material stresses?  Are these typically all…

A: Stress: Stress is defined as the internal resistance per unit area of cross-section. There are…

Q: If the circumference of the cross section of a cylinder bar is 25mm, what maximum axial load can it…

A: Given,  Circumference of the cylindrical cross section =25mm…

Q: 2) The negative low angle of attack (NLAA) flight condition leads to maximum tensile stresses on…

A: Answer= (A)

Q: A cylindrical specimen of 1018 steel having a diameter of 6.35 mm and a gauge length of 38.1 mm is…

A: The cross-sectional area of the specimen is The stress in the element can be determined as, The…

Q: Calculate the modulus of elasticity for a low - carbon steel which produces the following data when…

A: Since you have asked multiple questions in a single request we would be answering only the first…

Q: A tool steel cylindrical specimen, 6 in. long and 0.25 in. in diameter, is kept rotating like a…

A:

Q: Q2: Figure (2) shows an isometric view of a crankshaft that is actuated by the vertical force acting…

A:

Q: 7. In the Brinell hardness test, if the load used 1200 kg, and the ball diameter 6 mm, write down…

A:

Q: Q1-A/ In a tensile test on a metal specimen, true strain = 0.08 at a stress = 265 MPa. When the true…

A:

Q: etermine the diameter of a brittle member in inches if the tensile design load is 15,671 lb.…

A: Given:Tensile load, P=15,671 lbUltimate strength, Sut=60,000 psiN=5

Q: 85. During a hign cycle fatigue test, a metallic specimen is subjected to cyclic loading with a mean…

A: Given data,  σmean= 140 MPa,  σmin = 70 MPa

Q: for a machine part, the following stresses are determined at the most critical point: 0x = 100,0y =…

A:

Q: A cylindrical shape 25.0 mm in diameter and 21.0 mm in height is cut from a pear. Using an Instron…

A:

Q: CALCULATIONS 4.1 Using the given pulley radius and the weight values, calculate the torque applied…

A: Disclaimer: Since you have posted a question with multiple sub-parts, we will solve first three sub…

Q: Determine the maximum stress produced in a rectangular plate 50 mm wide, 8 mm thick with a central…

A: Given that, Axial tension, P=1 kN,Width of rectangular plate, b=50 mm,Thickness of plate, h=8…

Q: 4. What useful informations are obtained from the tensile test of a ductile material? 5. What do you…

A: 4.What useful informations are obtained from the tensile test of a ductile material?       Note :-…

Q: What force is required to compress a 200mm diameter hollow post with a thickness of 50mm thickness…

A: Given Data⇒ Internal diameter of hollow post(d)=200 mm Since 1 m=1000 mm Internal diameter of hollow…

Q: Wi Wz _F STEM PART 1 TAB TAB STEM TAB TAB PART2 BY NC SA 2014 Michael Swanbom Dimensions: WĄ W2 W3…

A: Stress is the ratio of force and area.

Q: Problem 1: The assembly below will be used for each problem. Lengths, diameters, and materials are…

A:

Q: Problem 9.10 Part A Determine the equivalent state of stress on an element at the same point…

A:

Q: . A machine component 50 inches in length is tested with a load of 100, 000 Ib. Considering an…

A: The diameter of the specimen is 3.25735 inch.

Q: 1. An engine cylinder is 300 mm in diameter and the steam pressure is 0.7 N/mm2. If the cylinder…

A:

Q: rectangular block is subjected to a tensile stress of 100 N/mm² on one plane and 50 N/ mm² on a…

A:

Q: A metal alloy has been tested in a tensile test with the following results for the flow parameters:…

A: solved

Q: Problem 9.51 In (Figure 1), Tzy = 55.3 MPa. Figure 80 MPa 1 of 1 > Part A Determine the principal…

A:

Q: A fatigue test was conducted in which the mean stress was 70 MPa (10,000 psi), and the stress am-…

A:

Q: What is Multiaxial Stress?

A: Multiaxial stress states due to the action of various external loads exist at the considered point…

Q: e cross sectioned rod of side ' a ' is fixed on the universal testing machine ; 'F' force is applied…

A: Stress = Force /Area

Q: A Brinell hardness measurement of 650 HBN, using a 10-mm-diameter indenter and a 2950 kg load on an…

A: Option d is correct 2.386mm

Q: ure 1 shows a compound bar with three different diameters, d1-9mm, d2-22mm, and d3-14mm machined…

A: P=30kN d1=9mm d2=22mm d3=14mm

Q: Q1 A round bar is subjected to a rotating force. State what type of stress is induced in the bar and…

A:

Q: A Brinell hardness measurement of 650 HBN, using a 10-mm-diameter indenter and a 2950 kg load on am…

A:

Q: 1. Define the terms load , stress and strain. Discuss the various types of stresses and strain. 2.…

A:

Q: A cylindrical shape 25.0 mm in diameter and 21.0 mm in height is cut from a pear. Using an Instron…

A:

Q: A tie rod of uniform section is required to resist a force of 450 kN at an eccentricity of 25 mm…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.