tion Rod AB is held in place by the cord AC. Knowing that the tension in the cord is 1350 N and that e = 360 mm, determine the moment about B of the force exerted by the cord at point A by resolving that force into horizontal and vertical components applied (a) at point A, (b) at point C. B 240 mm 450 mm

tion Rod AB is held in place by the cord AC. Knowing that the tension in the cord is 1350 N and that e = 360 mm, determine the moment about B of the force exerted by the cord at point A by resolving that force into horizontal and vertical components applied (a) at point A, (b) at point C. B 240 mm 450 mm

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter11: Angular Momentum

Section: Chapter Questions

Problem 55P: A diver off the high board imparts an initial rotation with his body fully extended before going...

See similar textbooks

Similar questions

The 6.8-kg frame AC and 2.8-kg uniform slender bar AB of length lslide with negligible friction along the fixed horizontal rod under the action of the 75-N force. Calculate the tension Tin wire BC and the magnitude FA of the force exerted on the bar by the pin at A. The x-y plane is vertical. 75 N 52° 52 B Answers: T = ! N FA = ! N lle
2/42 The cable AB carries a tension of 400 N. Determine the moment about O of this tension as applied to point A of the slender bar. B 650 mm 500 mm 30°
2/36 The tension in cable AB is 100 N. Determine the moment about O of this tension as applied to point A of the T-shaped bar. The dimension b is 600 mm. 60 B
Determine the force-couple system at O which is equivalent to the two forces applied to the shaft AOB. Is R perpendicular to Mo? Assume F1 = 600 N, F2 = 610 N, a = 75 mm, b = 170 mm, 0 = 20°, and o = 54°. A a b. B F, Answer: R = (i i+ i j+ i k) N Mo = ( i i+ i j+ i k) N-m
A crane is oriented so that the end of the 25-m boom AO lies in the yz plane. At the instant shown, the tension in cable AB is 4.9 kN. Determine the moment about each of the coordinate axes of the force exerted on A by cable AB. 15 m B -2.5 m The moment about the x-axis is |kN-m. The moment about the y-axis is kN-m. The moment about the z-axis is kN-m.
Assuming: moment counter clockwise is positive Determine the moment of H.W3 the force about point O. 3 ft 1 ft 45° 1 sin 45° ft 60 lb
A 366-N force is applied at A as shown. y = 370 mm. Determine (b) the smallest force applied at B that creates the same moment about D. Write numerical value and 2 decimal places. + for counterclockwise -100 mm- -200 mm y mm 25° A P D 125 mm C B
The 28-N force P is applied perpendicular to the portion BC of the bent bar. Determine the moment of P about point B and about point A. Moments are positive if counterclockwise, negative if clockwise. P = 28 N 1.3 m B o Answers: MB - i MA- i 40° 1.3 m N-m N-m
The particle of mass m = 2.2 kg is attached to the light rigid rod of length L = 0.80 m, and the assembly rotates about a horizontal axis through O with a constant angular velocity = ω = 3.9 rad/s. Determine the force T in the rod when θ = 33°. The force T is positive if in tension, negative if in compression. 1. Calculate the r- and θ-components of acceleration. 2. Determine the force T in the rod when θ = 33°
The force of magnitude F = 105 lb acts along the edge of the triangular plate. Determine the moment of F about point O. The moment is positive if counterclockwise, negative if clockwise. 20" 13" F = 105 lb B Answer: Mo= i lb-in.
H.W: Find the Centen of mass-of a thin Plate f denisity S=3 bounded by the Lines Xa o, y=x iad the parabola y2 2- x in the first qivedrant * : 7 = 38 35 H.w: Find the moment d inentia ad the about the X axis y Kadrus g ay ration a thin plate bounded by the parabola X y- y ad the line X+y ao if = 64 Ry z 号 I, %3D 105
Sl units of bending moment is kN^2 O kN.m km O kN