The cylindrical plunger traveling at V₂ = (0.005 t¹/2) m/s, where t is in seconds, injects a liquid plastic into the mold to make a solid ball. The diameter of plunger is d = 50 mm. (Figure 1) Determine the amount of time needed to do this if the volume of the ball is V=²³ Express your answer to three significant figures and include the appropriate units. t= 56.7 μÃ S Submit Previous Answers Request Answer ?

The cylindrical plunger traveling at V₂ = (0.005 t¹/2) m/s, where t is in seconds, injects a liquid plastic into the mold to make a solid ball. The diameter of plunger is d = 50 mm. (Figure 1) Determine the amount of time needed to do this if the volume of the ball is V=²³ Express your answer to three significant figures and include the appropriate units. t= 56.7 μÃ S Submit Previous Answers Request Answer ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel measuring tape used by a civil engineer is 50 m long and calibrated at 20oC.The tape measures a distance of 35.694m at 35oC. What is the actual distance measured? D = D L L T ( )( )( ) a Coefficient of linear expansion of steel a = 1.2 x 10-5oC-1
1 Proof that a solid aluminum block of 4 mm x 3 mm x 3 mm, such as shown in FigureQ1 (a), can float on water at 20 °C due to the effect of surface tension. The density ofthe aluminum block is 2700 kg/m3. Determine the contact angle. 2. A solid alloy cylinder having a diameter of 6.48 cm slides downward at a terminalvelocity of V through a vertical pipe. The downward motion is resisted by an oil filmbetween the piston and the pipe wall. Determine the oil viscosity when the velocityV is 5 m/s. The inner diameter of the vertical pipe is 6.5 cm, and the alloy density is3500 kg/m3.
The cage system shown in the figure is made of EC rod. The Flow Limit of the material is 180 MPa and the Safety Coefficient is 4 is desired to be. Accordingly, the circular cross section EC rod Calculate the diameter.
Q.2) The assembly shown below is composed of an aluminum tube and a cylindrical steel plug. The mass density of aluminum and steel are 2700 kg/m³ and 7800 kg/m³, respectively. Find the coordinates of the mass center. y Tube A- Plug 20 mm 35 mm 100 100 A- mm mm Section A-A
16 mil 3 cm 8 cm --+- -D=9 cm- Water The can in the given image floats in the position shown. The diameter of the can is 9cm. what is its weight in Newtons?
An aluminum cylinder (s.g=2.7) 15 cm high and with diameter d=8.1 cm slides down inside a tube with inner diameter D=8.2 cm, as shown in the figure. The cylinder is concentric with the axis of a tube and between them there is a thin film of oil of s.g. =0.8 with a kinematic viscosity of 0.075St. a) What is the (constant) rate of fall of the cylinder inside the tube? b) determine the torque needed to keep the inner cylinder rotating at an angular speed w=200rpm D
Silo is a large tank-like container for storing granular materials or powder, for example a grain one. Select one: True False
2. The cylinder shown in figure 2 is made from a uniform material. What is its specific weight? Kerosene at 25°C(SG=0.823) 750 mmi 600 mm 400 mm Figure 2
This is a hemispherical shell filled with water. Radius of hemispherical shell = 2 m Diameter of sharp-edge orifice= 150 mm. (positioned at the bottom point) C = 0.60 What is the time needed to empty the hemispherical shell through the orifice? (Kindly provide a complete solution)
Figure P2.33 shows a portion of the H,O-NaCl phase diagram. 10 Liquid (brine) Salt Ice + -10 F liquid (brine) liquid (brine) -20 Ice + salt -30 NaCI 10 20 30 H2O 100 90 80 70 FIGURE P2.33 Composition, weight % a. Using the diagram, briefly explain how spreading salt on ice causes the ice to melt. Show numerical examples in your discussion. b. At a salt composition of 10%, what is the temperature at which ice will start melting? c. What is the eutectic temperature of the ice and salt combination? Temperature, °C
O t will be suspended in the liquid. PROBLEM 3. Compute the capillary effect of immersion in water of a glass 5 points tube of 4mm internal diameter given the surface tension value is 0.073573 N/m, the density value is 990 kg/m^3 and the angle of contact is zero. Express your answer in SI units.. Indicate the appropriate unit. * Your answer
CIVIL ENGINEERING FDRAULICS dynes A capillary tube of a uniform bore is dipped vertically in water which rises by 7 cm in the tube. Find the radius of the capillary if the surface tension is 70- Cm A liquid rises to a height of 9 cm in a glass capillary of radius 0.02 cm. What will be the height of the liquid column in a similar glass capillary of radius 0.03 cm?