The crane and boom shown in Fig. P6-69 weigh 12,000 lb and 600 lb, respectively. The pulleys at D and E are small, and the cables attached to them are essentially parallel. determine the location of the resultant force on the thread relative to point c when the load lifted is 3600 lb (consider the fbd of the system) maginitude of the pin reaction at boom support A when the lifted load is 3600 lbs. (consider fbd of pulley b and fbd of boom ab)

The crane and boom shown in Fig. P6-69 weigh 12,000 lb and 600 lb, respectively. The pulleys at D and E are small, and the cables attached to them are essentially parallel. determine the location of the resultant force on the thread relative to point c when the load lifted is 3600 lb (consider the fbd of the system) maginitude of the pin reaction at boom support A when the lifted load is 3600 lbs. (consider fbd of pulley b and fbd of boom ab)

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.10.7P

See similar textbooks

Similar questions

Q4 please fast
Compute the compressive strength of a WT 12x81 of A992 steel. The effective length with respect to the x-axis is 25 feet 7inches, the effective length with respect to the y axis is 20feet, and the effective length with respect to the z-axis is 20 feet WT12X81 A 23.9 t₁ 1.22 ly 221 d 12.5 k des 1.72 J 9.22 bf 13.0 y 2.70 Cw 43.8 tw 0.705 293
find out F, KN F23 f13 f16
Q1 With fbd.
3 ft 3 ft L K B C D E F -4 ft-4 ft 4 ft 4 ft 4 ft4 ft- F, F, F₁ F₂ F,
A= 63.04 cM², bF = 100 wm, tF = IS-3 wm For ISMC 400 tw = 8.6 mm, Ixx = 15123.4 cm4 For ISA 1asx75X 10 Iyy e 8t-6 an, Crr = 4.04 cm Ivy = s06.3 cnt, cuy = 243 cM ISA 125X TSX10 A = 19.02 Cu? Ixx = 300. 3 CM", Cy y = 1. 76 cm ISMC 400 For the builtup section shown in the figure, provided are the details of the individual structural properties. Find: [ Select ] The x bar from the bottom of the overall figure [ Select] the centroidal MOI lyy
H.W: draw the I.L for RA, RC, RF, RD, MD, VCL, VG and MG. A 2 m B -2 m C G 0.4 m 1.6 m D 2 m- E 2 m LL
Convert the properties of your assigned AASHTO I-beams to Sl units. B1 BI Assigned AASHTO I-beam Туре 1 Туре 2 Group No. D2 1 D3 D2 2 D4 B3 B4 B5 Туре 3 Туре 4 Туре 5 Туре 6 B3 B4 4 DI B6 B6 D5 D6 DS Туре 1 Туре 2 8 B2 D6 Туре 1-IV Dimensions (inches) Type V-VI Туре D1 D2 D3 D4 D5 D6 B1 B2 B3 B4 B5 B6 28 4 3 5 5 12 16 6 3 5 II 36 3 6 6 12 18 6 3 6 III 45 4.5 7.5 7 16 22 7 4.5 7.5 IV 54 8. 6 8. 20 26 8 6. 9 V 63 4 10 8. 42 28 8 4 13 10 VI 72 5 3 4 10 8 42 28 8 4 13 10 Properties: Area in.? Inertia Ybottom in. Weight kip/ft Туре in. 276 12.59 22,750 0.287 II 369 15.83 50,980 0.384 III 560 20.27 125,390 0.583 IV 789 24.73 260,730 0.822 V 1,013 31.96 521,180 1.055 VI 1,085 36.38 733,320 1.13 67
12 AB, AC, BC, BD, BE, BF, CF, DE, EF 1200 Ib 12 2400 lb 1200 Ib
Two columns 300mmx300mm and 400mmx400mm are loaded by axial and bending forces as shown. They are to be supported by a combined footing shown. Unit weight of concrete = 24 kN/m2;Unit weight of soil = 17.24 kN/m3; fc'=21 MPa, fy = 414 MPa, Concrete Cover to bar centroid 80 mm, SBC=248 kPa. Dimensions: X 4 meters thickness = 568 mm %3D D = 1.73 meters Forces: P1DL = 239 kN P1LL = 177 kN M1DL = 38 kN-m %3! M1LL = 30 kN-m P2DL = 495 kN %3D P2LL 393 kN %3D M2DL = 65 kN-m M2LL 65 kN-m Calculate the critical nomninal one way shear stress in MPa.
Situation 5: A W4x13 has a length of 3.5 m. Fy 248 MPa. The properties are given below. Properties of W shape A 2,470 mm^2 d-106 mm bf - 103 mm tf-8.76 mm kdes 15.1 mm tw- 7.11 mm rx-43.7 mm ry= 25.4 mm 1. Which of the following most nearly gives the axial capacity (Pa) of the column if one end is fixed and the other is pinned connected? 226 KN 215 KN. O 244 KN O 260 KN
1- For the beam shown in the figure below: aReplace the loading system with an equivalent resultant force and couple moment at point A. b) Replace the loading system with an equivalent resultant force and couple moment at point B. 650 N 30° 1500 Nm TH 300 N -3 m- -5 m- 500 N 60 -2 m