The compound beam consists of the two solid steel rods bolted together along their length. The beam initially positioned as shown in (Figure 1) later was rotated 90° about the line of touch of the rods, so that both rods rest on the supports at A (pin) and B (roller), while the unchanged loading became evenly distributed on both rods. Suppose that P = 70 kN. Figure 20 kN/m 2m 2m < 1 of 1 > Determine the required diameter d of each of the rods if the allowable bending stress is allow=130 MPa. Express your answer to three significant figures and include the appropriate units. d= Value Submit μA Provide Feedback Request Answer Units ?

The compound beam consists of the two solid steel rods bolted together along their length. The beam initially positioned as shown in (Figure 1) later was rotated 90° about the line of touch of the rods, so that both rods rest on the supports at A (pin) and B (roller), while the unchanged loading became evenly distributed on both rods. Suppose that P = 70 kN. Figure 20 kN/m 2m 2m < 1 of 1 > Determine the required diameter d of each of the rods if the allowable bending stress is allow=130 MPa. Express your answer to three significant figures and include the appropriate units. d= Value Submit μA Provide Feedback Request Answer Units ?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.4.17P: .17 A mountain-bike rider going uphill applies torque T = Fd(F = l5lb, d = 4 in.) to the end of the...

See similar textbooks

Similar questions

Repeat Problem 9,5-15 for the anti-symmetric loading shown in the figure.
A temporary wood flume serving as a channel for irrigation water is shown in the figure. The vertical boards forming the sides of the flume are sunk in the ground, which provides a fixed support. The top of the flume is held by tic rods that are tightened so that there is no deflection of the boards at that point. Thus, the vertical boards may be modeled as a beam AB, supported and loaded as shown in the last part of the figure. Assuming that the thickness t of the boards is 1,5 in., the depth d of the water is 40 in., and the height h to the tie rods is 50 in., what is the maximum bending stress in the boards? Hint: The numerically largest bending moment occurs at the fixed support.
Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
Repeat Problem 6.2-1 but now assume that the steel plate is smaller (0.5 in. × 5 in.) and is aligned with the top of the beam as shown in the figure.
.17 A mountain-bike rider going uphill applies torque T = Fd(F = l5lb, d = 4 in.) to the end of the handlebars ABCD by pulling on the handlebar extenders DE. Consider the right half of the handlebar assembly only (assume the bars are fixed at the fork at A). Segments AB and CD are prismatic with lengths L, = 2 in.andL3 = 8.5 in, and with outer diameters and thicknesses d01 = 1.25 in. 101 = 0.125 in. and d03 = O.87in.,i03 = 0.ll5in, respectively as shown. Segment BC’ of length L, = 1.2 in. however. is tapered, and outer diameter and thickness vary linearly between dimensions at B and C. Consider torsion effects only. Assume G = 4000 ksi is constant. Derive an integral expression for the angle of twist of half of the handlebar tube when it is subjected to torque T = Fd acting at the end. Evaluate ‘b1-, for the given numerical1ues.
-7 Repeat Problem 2.3-5, but n include the weight of the bar. See Table I-I in Appendix I for the weight density of steel.
A beam supported with pin joint at 1 and roller support at 2 carries point loads of F1= 10 kN at A, F2= 34 kN at B, F3= 16 kN at C, and F4= 14 kN at D. Schematic arrangement of the supports and beams with their distances L1 = 376 mm, L2 = 157 mm. L3 = 3438 mm. L4 = 1340 mm and, L5 = 1821 mm are as shown in Figure T1. The students are to position the loads and supports as per the dimensions given and perform the following: (). Draw the physical diagram of the beam; (N). Draw the free body diagram of the beam; (N). Estimate the reaction forces at the support; (v). Draw shear force and bending moment diagrams for the given values and identify maximum shear force and maximum bending moment; (v). Identify the support with maximum reaction and provide justification for the answer. F3 F4 L5 L3 L4 Figure T1 (All dimensions are in mm)
700N M-150UNm 2m 3m For the above dlagram, given that F, - 450 N. 0-45 degrees and d-5 m calculate the following (neglect the depth of the beam). Note that there is a pin support at A and a roller support at B. The magnitude of the horizontal component of the reaction force at A, Rar. Please provide the answer in Newtons and report to three significant figures. Please Include the unit ("N") within your answer (eg. If the calculated answer was 55.562 Newtons please Input: 55.6 N). Answer: The magnitude of the vertical component of the reaction force at A, Rar. Please provide the answer in Newtons and report to three significant figures. Please include the unit ("N") within your answer (eg. If the calculated answer was 55.562 Newtons please Input: 55.6 N). Answer: The magnitude of the horizontal component of the reaction force at B. Re. Please provide the answer in Newtons and report to three significant figures. Please Include the unit ("N") within your answer (eg. If the calculated…
The beam shown below is supported by rollers at A and B, and by a pin at C. If EI is constant over the length of the beam, find the reaction forces at A, B, and C. 15 kip AT 6 ft B_ 6 ft 12 ft 3 kip/ft C
3. Determine the displacement and slope (i.e. 0) at the load point for the stepped beam shown in the following figure. Also determine the reaction forces and moments. Each element has E = 200 GPa. The area moment of inertia are given as I₁ = 1.25 × 105 mm4, and 2 = 4 x 104 mm. Clearly show the elemental stiffness matrices (k) for each element, assembly of k matrices to get global stiffness matrix (K) and application of boundary conditions. Then solve the reduced K matrix to get displacements and reactions 3000 N 150 mm 75 mm 125 mm
A beam supported with pin joint at 1 and roller support at 2 carries point loads of F1= 11 kN at A, F2= 47 kN at B, F3= 17 kN at C, and F4= 16 kN at D. Schematic arrangement of the supports and beams with their distances L1 = 168 mm, L2 = 474 mm, L3 = 2808 mm, L4 = 2673 mm and, L5 = 1820 mm are as shown in Figure T1. The students are to position the loads and supports as per the dimensions given and perform the following: (iv). Draw shear force and bending moment diagrams for the given values and identify maximum shear force and maximum bending moment; (v). Identify the support with maximum reaction and provide justification for the answer.
Example The beam ABC is loaded via a 500 N.m couple and a 600 N force as shown. The beam is connected to the rest of the system by a pin joint at B and a roller support at C. Detemine the magnitude of the reaction forces on the beam at the supports. 600 N 500 N.m 400 300 500 Ans. RC=1700 N RBx=1597.5N Dimensions in mm REDMI NOTE 9 PRO AI QUAD CAMERA RBy=1181.4 N