The compound bar containing steel bronze and aluminum segments carries the axial loads shown in the figure. The properties of the segments are listed in the table. Determine the maximum allowable value of P in pounds if the change in length of the entire bar is limited to +0.07in. Steel Bronze Aluminm (A) 22,250 B) 26,250 25,250 D) 27,250 A (in²) 0.75 1 0.5 2P Steel 2 ft Bronze 4 ft -5P E (psi) 30000000 12000000 10000000 4P+ Aluminum 3 ft P L (FT) 2 4 3

The compound bar containing steel bronze and aluminum segments carries the axial loads shown in the figure. The properties of the segments are listed in the table. Determine the maximum allowable value of P in pounds if the change in length of the entire bar is limited to +0.07in. Steel Bronze Aluminm (A) 22,250 B) 26,250 25,250 D) 27,250 A (in²) 0.75 1 0.5 2P Steel 2 ft Bronze 4 ft -5P E (psi) 30000000 12000000 10000000 4P+ Aluminum 3 ft P L (FT) 2 4 3

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A compressive load P is transmitted througha rigid plate to three magnesium-alloy bars that areidentical except that initially the middle bar is slightlyshorter than the other bars (see figure). The dimensionsand properties of the assembly are as follows:length L = 1.0 m, cross-sectional area of each barA = 3000mm2, modulus of elasticity E = 45 GPa,and the gap s = 1.0 mm.(a) Calculate the load P1 required to close the gap.(b) Calculate the downward displacement d of therigid plate when P = 400 kN.(c) Calculate the total strain energy U of the threebars when P = 400 kN.(d) Explain why the strain energy U is not equal toPδ / 2. Hint: Draw a load-displacement diagram.
One of the following values is a possible for possion ratio for steel ? a. Zero b. one c. 0.3 d 0.9
REINFORCEB=(335mm)H=(435mm)
1.A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are € E =0.40x10-3 and ɛ =0.3 x 10- determine O and o. Use E = 110 GPa and v=0.35. y y. = Blank 1 MPa Answer in 1 decimal place = Blank 2 MPa Answer in 1 decimal place
What is the value of reduction factor of the beam, if the stress in the steel is 400 MPa, and the Modulus of Elasticity of the Steel is 200,000 MPa. O 0.671 0.692 O 0.660 O 0.650 None of the Choices O 0.681
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. %3D Steel E200 GPa A-600mm L1 m 2.0 m 0.6 m 1.5 m Pa20 KN Aluminum E-70 GPa A=900mm L-1.5 m What is the ratio of the deformation of steel to deformation of aluminum?
The modulus of elasticity of mild steel is equal to .. .? .... .. a. 2 x 10ʻN/m? a. 2 x 10'N/m 2 b. 2 x 10° N/m 4 c. 2 x 10 N/mm 5 d. 2 x 10 N/mm Check
Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was 15 degrees Celsius and the stress on the bars is zero. Eventually, the temperature increased to 25 degrees Celsius. Determine the total deformation on the steel. Steel Brass Copper Est = 200 GPa Ebr = 100 GPa Ecu = 120 GPa %3D ast = 12(10-6)/°C abr = 21(10¬6)/°C acu = 17(10-)/°C %3D Acu = 515 mm² |Ast = 200 mm? Abr = 450 mm² %3D 300 mm- 200 mm 100 mm O -0.0058mm O 0.0165mm O -0.0165mm O 0.0058mm
As shown in the figure below, a bronze bar is affixed between a steel bar and an aluminum bar. Axial loads are applied at the positions indicated. If the largest value of P that will not exceed an overall deformation of 4.0 mm, or the following stresses: 150 MPa in the steel, 130 MPa in the bronze, and 90 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. determine the stress in the bronze, steel, and aluminum
Given : Steel: A = 600mm2 ; E = 200 GPa Bronze : A = 900mm2 ; E = 83 GPa Show the complete solution and FBD
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²