The beam supports the loads as shown in the figure. Using E = 200 GPa, w = 16kN/m, P= 25kN and M = 22kNm, L₁ = 2m, L₂ = 8, L3 = 2m and a=25mm. Find, a. If w is spread over L₁ and L2, and P and M are interchanged, determine the midspan EIS and deflection by moment - area method Strictly show all of the free body diagrams used upon solving the problem. Complete solution is a must. 6a B 10a M4 - يا ــــــــ 3a

The beam supports the loads as shown in the figure. Using E = 200 GPa, w = 16kN/m, P= 25kN and M = 22kNm, L₁ = 2m, L₂ = 8, L3 = 2m and a=25mm. Find, a. If w is spread over L₁ and L2, and P and M are interchanged, determine the midspan EIS and deflection by moment - area method Strictly show all of the free body diagrams used upon solving the problem. Complete solution is a must. 6a B 10a M4 - يا ــــــــ 3a

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the horizontal and vertical deflections at D for the frame shown below (consider E, I constant and neglect axial deformation). P |2L A В C 4L
For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at B and (b) the deflection of the beam at A. Assume a constant value of El = 145000 kip-ft2 for the beam; wo = 5.6 kips/ft, LAB = 13ft, LBc = 7 ft. Wo Answer: (a) 8B = (b) VA = LAB rad in. B LBC C X
Q2. Calculate the deflection at point D for the following static beam structure using the Unit Load and Moment Area method P = a kN D q = a +b B EI b/4 m b/2 m b Where: E3D 210 х 106 I= 8360 x 10-8 a = 3 b = 2a 3 b b A = (2/3) A = (1/3)
The beam ABC is subjected to a point load at the middle of segment AB and a uniformly distributed load at the segment BC, as shown in the figure. A L Find the deflection at point C. 20 N B 1.5W, N/m H Figure 1: Overhang beam L C Set wo = 3 N/m, L = 2 m, EI = 25000 Nm². Use the method of superposition for all parts. Hint: for x > L/2 in segment AB, the solution can be obtained from the table by replacing x by L-x.
The beam ABC is subjected to a point load at the middle of segment AB and a uniformly distributed load at the segment BC, as shown in the figure. A L 20 N B 1.5W, N/m Figure 1: Overhang beam Find the deflection at the middle of the segment AB L C Set wo = 3 N/m, L = 2 m, EI = 25000 Nm². Use the method of superposition for all parts. Hint: for x > L/2 in segment AB, the solution can be obtained from the table by replacing x by L-x.
1. A horizontal simply-supported beam is loaded as shown in Figure 1. It has a rectangular cross section, 70 mm by b mm. (a) Determine the vertical reaction forces at A and E. (b) If the allowable deflection at mid-span is 2 mm downwards, determine the dimension, b, of the beam needed. Use E= 150 GPa. 10kN 6kN/m 4kNm [36.26mm] Section A-A of Beam AF 0.2m 0.3m 0.8m E olo 水水 0.2m 0.3m 3kN Figure 1
For the beam shown, EI = Constant. Determine the following: A. Slope at B B. Deflection at C C. Location of the maximum deflection D. maximum deflection
QUESTION 03 A beam ABCD is supported and loaded as shown in Figure Q3. The flexural rigidity, El is constant. By using Macaulay's method, and take point A as origin, determine the: (a) Reactions at all supports A, C and D. (b) Deflection at point B (c) Slope at support A 1 m 1 m 1 m 2 kN/m 4 kNm Figure Q3/ Rajah S3
A truss carries a concentrated load at points B, E, F, and G as shown in the figure below. Using unit load method, determine the deflection of the following point. All members of the truss have a circular cross-section: Top Chord has a diameter of 25mm: Bottom chord has a diameter of 37mm; Web member has a diameter of 12mm. USE E=200GPA. 2P F 2P G E 300 60° B 600 30 D A ЗР 4m 4m 4m If the reaction of point D is 72.886751345948KN, determine the value of "P". Determine the vertical deflection of point B. Determine the vertical deflection of point C. Determine the horizontal deflection of point G. Determine the force acting at member FG due to applied force. (NOTE: Put a negative sign if your answer is compressive force, otherwise just put your answer) P.
Use AREA MOMENT METHOD to Determine the following: A central beam BD is joined at hinges to two cantilever beams AB and DE. All beams have the cross-section shown. For the loading shown, determine the largest w so that the deflection at C does not exceed 3mm. Use E=200 GPa. w 12 mm A C D E Hinge' Hinge 24 mm 0.4 m 0.4 m 0.4 m 0.4 m
For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at B and (b) the deflection of the bearn at C. Assume a constant value of EI = 34 x 106 lb-ft² for the bear; wo = 6400 lb/ft, LAB= 4.0 ft. LBC = 9ft,Lco=5 ft. LAB Answer: (a) 8B = (b) vc= Wo B LBC rad in. LCD D X
Determine the deflection at joint G. Consider uniform cross-sectional area A= 500mm^2 and modulus elasticity E for all members is 200 GPa Using Castigliano's Theorem P in KN B. H G 4@2m = 8 m P= 279 kN 2P in KN D F 4m