The 10 resistor in (Figure 1) is dissipating 35 W of power. Figure ww www 10 (2 5.0 92 ww 20 Ω 1 of 1 How much power is the 5.0 2 resistor dissipating? Express your answer with the appropriate units. Pso = Submit ▾ Part B μA P20 = Value Submit X Incorrect; Try Again; 5 attempts remaining Previous Answers Request Answer How much power is the 20 S2 resistor dissipating? Express your answer with the appropriate units. Units HA Value [X] < Return to Assignment Units Previous Answers Request Answer ? X Incorrect; Try Again; 4 attempts remaining Provide Feedback ?

The 10 resistor in (Figure 1) is dissipating 35 W of power. Figure ww www 10 (2 5.0 92 ww 20 Ω 1 of 1 How much power is the 5.0 2 resistor dissipating? Express your answer with the appropriate units. Pso = Submit ▾ Part B μA P20 = Value Submit X Incorrect; Try Again; 5 attempts remaining Previous Answers Request Answer How much power is the 20 S2 resistor dissipating? Express your answer with the appropriate units. Units HA Value [X] < Return to Assignment Units Previous Answers Request Answer ? X Incorrect; Try Again; 4 attempts remaining Provide Feedback ?

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter9: Current And Resistance

Section: Chapter Questions

Problem 55P: A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any...

See similar textbooks

Similar questions

Integrated Concepts A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. (a) What is the battery’s internal resistance? (b) What power is dissipated inside the battery? (c) At what rate (in °C/min ) will its temperature increase if its mass is 20.0 kg and it has a specific heat of 0.300 kcal/kg. °C, assuming no heat escapes?
Integrated Concepts (a) An immersion heater utilizing 120 V can raise the temperature of a 1.00 102 -g aluminum cup containing 350 g of water from 20.0°C to 95.0°C in 2.00 min. Find its resistance, assuming it is constant during the process. (b) A lower resistance would shorten the heating time. Discuss the practical limits to speeding the heating by lowering the resistance.
A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any wires used for connections is negligible, (a) What is the current through the resistor? (b) What is the power dissipated by the resistor? (c) What is the power input from the battery; assuming all the electrical power is dissipated by the resistor? (d) What happens to the energy dissipated by the resistor?
A car battery with a 12-V emf and an internal resistance of 0.050 is being charged with a current of 60 A. Note that in this process the battery is being charged. (a) What is the potential difference across its terminals? (b) At what rate is thermal energy being dissipated in the battery? (c) At what rate is electric energy being converted to chemical energy? (d) What are the answers to (a) and (b) when the battery is used to supply 60 A to the starter motor?
Check Your Understanding Handheld calculators often use small solar cells to supply the energy required to complete the calculations needed to complete your next physics exam. The current needed to run your calculator can be as small as 0.30 mA. How long would it take for 1.00 C of charge to flow from the solar cells? Can solar cells be used, instead of batteries, to stall traditional internal combustion engines presently used in most cars and trucks?
In Figure 21.41. does the graph indicate the time constant is shorter for discharging than for charging? Would you expect ionized gas to have low resistance? How would you adjust R to get a longer time between flashes? Would adjusting R affect the discharge time?
Consider the circuit shown in Figure P28.21 on page 860. (a) Find the voltage across the 3.00-0 resistor, (b) Find the current in the 3.00-12 resistor.
Three 100- resistors are connected as shown in Figure P21.41 The maximum power that can safely be delivered to any one resistor is 25.0 W. (a) What is the maximum potential difference that can be applied to the terminals a and b? (b) For the voltage determined in part (a), what is the power delivered to each resistor? (c) What is the total power delivered to the combination of resistors?
(a) A defibrillator sends a 6.00-A current through the chest of a patient by applying a 10,000-V potential as in the figure below. What is the resistance of the path? (b) The defibrillator paddles make contact with the patient through a conducting gel that greatly reduces the path resistance. Discuss the difficulties that would ensue if a larger voltage were used to produce the same current through the patient, but with the path having perhaps 50 times the resistance. (Hint: The current must be about the same, so a higher voltage would imply greater power. Use this equation for power: P=I2 RP = .)
A typical cell phone consumes an average of about 1.00 W of electrical power and operates on 3.80 V. (a) What average current does the phone draw from its battery? (b) Calculate the energy stored in a fully charged battery if the phone requires charging after 5.00 hours of use.
Currents of approximately 0.06 A can be potentially fatal. Currents in that range can make the heart fibrillate (beat in an uncontrolled manner). The resistance of a dry human body can be approximately 100 k . (a) What voltage can cause 0.06 A through a dry human body? (b) When a human body is wet, the resistance can fall to 100 . What voltage can cause harm to a wet body?
Integrated Concepts (a) Assuming 95.0% efficiency for the conversion of electrical power by the motor, what current must the 12.0-V batteries of a 750-kg electric car be able to supply: (a) To accelerate from rest to 25.0 m/s in 1.00 min? (b) To climb a 2.00 102-m- high hill in 2.00 min at a constant 25.0-m/s speed while exerting 5.00 102 N of force to overcome air resistance and friction? (c) To travel at a constant 25.0-m/s speed, exerting a 5.00 102 N force to overcome air resistance and friction? See Figure 20.44.