Study the heat treated steel workpiece shown in Figure A. Its dimensions are width w = 30 mm, height h = 50 mm, length / = 150 mm. The top surface of the workpiece is slimmed down with a material removal rate (MRR) of 2250 mm/min. %3D What is the depth of cut d within 1 minute in case you remove the material with slab milling?

Study the heat treated steel workpiece shown in Figure A. Its dimensions are width w = 30 mm, height h = 50 mm, length / = 150 mm. The top surface of the workpiece is slimmed down with a material removal rate (MRR) of 2250 mm/min. %3D What is the depth of cut d within 1 minute in case you remove the material with slab milling?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

The basic function of an automobile's carburetor is to atomize the gasoline and mix it with air to promote rapid combustion. Assume that 40 cm? of gasoline is atomized into N spherical droplets. Each droplet has a radius of 2.0 x 10-5 m. Find the total surface area of these N spherical droplets.
An engineering apprentice is given a rectangular sheet of metal of dimensions 500mm x 300mm. She is asked to cut out four identical squares, one in each corner of the sheet, fold up the sides and weld the corner seams to make a metal box. What should she make the length of the sides of the squares in order to maximise the volume?
Flow rate is expressed as gas velocity in cm/s. The gas is flowing through an open tubular column with an inner diameter of 0.25 mm. What volume flow rate (mL/min) corresponds to a gas velocity of 50 cm/s? (The volume of a cylinder is pr2 3 length, where r is the radius.)
Two cylindrical cross section water tanks are arranged so that the outflow from tank 1 falls into tank 2. The outflow from tank 2 flows to the drain. ģ is the volumetric flow rate out of a tank, and h is the height of the water in a tank. (a) State the fundamental physical law, and provide the general equation for a tank used to model the time history of the tank levels, h, and hz. Your equation should contain the following terms: A (eross sectional area of a water tank), p (density of water), and h (rate of change of the height of the water in a tank) (b) Both outflows have the characteristic volumetric flow rate being directly proportional to the head in the tank. ie. ġ1 = a, h, and q2 = azh2. Show that the differential equation governing the head in tank 2 has the form of : h, + ah, = be" Time, t, is the independent variable. Take the initial values of the heads to be A h(0) = H, and h,(0)= H,. Determine a, b and c. (Note: There is no d, or hi in the equation governing tank 2. You…
A cylindrical enclosure is rotated rapidly and steadily about a horizontal axis. Molten metal is poured into the rotating cylindrical sheath and then cooled, forming the finished product. Turning the sheath at a high rotation rate forces the solidifying metal strongly to the outside. Any bubbles are displaced toward the axis, so unwanted voids will not be present in the casting. The guide at the factory challenges your group to solve the following problem in under a minute: Suppose a copper pipe of inner radius 1.33 cm and outer radius 1.49 cm is to be cast. To eliminate bubbles and give high structural integrity, the centripetal acceleration of each bit of metal should be at least 100g. What rotation rate, in revolutions per minute, is required? You are determined to be the first one to get the answer.
What is the mass density δ(x, y, z) of a solid of volume 5 m^3 with uniform mass density and total mass 25 kg?
Gold, which has a density of 19.32 g/cm3, is the most ductile metal and can be pressed into a thin leaf or drawn out into a long fiber. (a) If a sample of gold, with a mass of 27.63 g, is pressed into a leaf of 1.000 mm thickness, what is the area of the leaf? (b) If, instead, the gold is drawn out into a cylindrical fiber of radius 2.500 mm, what is the length of the fiber?
h the beam section eiven bebw, the concrete and steel are ocos and 0,004, respectively. mm is the area of reinforcement to be placed c 30/37-842oc, Control is good, elongation rotions How many 2. according to demand. Material 300 MM 2 Monent carrying capacity if the rectangular section in the you calculated. first question has the How area of reinfforcement many kNM is Mc
An automobile tire is shown in the figure below. The tire is made of rubber with a uniform density of 1.10 ✕ 103 kg/m3. The tire can be modeled as consisting of two flat sidewalls and a tread region. Each of the sidewalls has an inner radius of 16.5 cm and an outer radius of 30.5 cm as shown, and a uniform thickness of 0.645 cm. The tread region can be approximated as having a uniform thickness of 2.50 cm (that is, its inner radius is 30.5 cm and outer radius is 33.0 cm as shown) and a width of 21.2 cm. What is the moment of inertia (in kg · m2) of the tire about an axis perpendicular to the page through its center?
Air flows at 210 m/s through the pipe. The temperature is 400 K and the absolute stagnation pressure is 280 kPa. Assume isentropic flow. For air R = 286.9 J/[kg - K] and k=1.40. (Figure 1) Figure 0.3 m
Q1 Calculate the packing factor (P.F) of diamonds. Hint: Take the plane (110)
What is the pressure of the gas in the cylinder, in kPa (kiloPascal)? h = 0.700 m, ρmercury = 13,600 kg/m3, 1.0 atm = 1.00 × 105 Pa = 100 kPa, and g = 10.0 m/s2. Your answer needs to have 3 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement.