Solve all for an upvote Two wooden member are glued together as shown. Each member has a width of b = 1.50 in. and a depth of d = 3.50 in. Use ẞ= 75° and P = 1,300 lb. a) Determine the internal N and V loads on the angled face labeled with *. Draw a free body c) Draw a 3D stress element that is aligned with the top, bottom, and left surfaces of the wooden members. Label all normal and shear stress components on this stress element. * d P

Solve all for an upvote Two wooden member are glued together as shown. Each member has a width of b = 1.50 in. and a depth of d = 3.50 in. Use ẞ= 75° and P = 1,300 lb. a) Determine the internal N and V loads on the angled face labeled with . Draw a free body c) Draw a 3D stress element that is aligned with the top, bottom, and left surfaces of the wooden members. Label all normal and shear stress components on this stress element. d P

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

ABC company, a textile manufacturing company, has recorded defects in their production for a month as shown in the table below. Following Pareto Analysis, which among the type/s of defects should be solved first to solve 80% of the problem? DEFECT FREQ MISPRINTING 55 SHADE VARIATION 38 UNEVEN DYEING 10 DROP STITCHING 5 DIRT/STAINS 2
Use MOST to determine the number of TMUs associated with each of the following scenarios: An assembly operator picks up a bolt located 10 inches away and places it (with no need for adjustments) into a pre-drilled hole 6 inches away from the initial location of the bolt. A B G A B P A
"The table below is data on telephone usage time by operators to serve customer requests that will be used to explain the use of Xbar and R-chart". Question: a. Create UCL and LCL with Limit Control Factor A2b. Create UCL and LCL with Limit Control Factor D3 and D4
A common problem that many drivers encounter is a car that will not start. Create a i shbone diagram to assist in the diagnosis of the potential causes of this problem.
In hydraulic fracture test, an induced fracture was created at 12.8 MPa. The fracture was reopened in three subsequent cycles. The reopening pressure at third cycle was found to be 6.4 MPa. If the tensile strength of rock is 6.3 MPa, and the pore water pressure is negligible. Determine the maximum and minimum principle stresses if the shut - in pressure was found to be 5.9 MPa
Defects Problem: The housekeeping supervisor of a hotel has been concerned about the number defects in rooms recently cleaned. In order to evaluate the true magnitude of the problem the supervisor has selected a random sample of 20 rooms each over a ten week period. The number of rooms with defects are as follows: Week Number of Defects 1 1 2 3 3 2 4 1 5 4 6 1 7 2 8 0 9 3 10 1 Determine the centerline, the upper and lower control limits ******The answer below was answered by another expert of yours and it was incorrect...Please give me the correct answer, please. Thanks***** Center Line: 1.8 Upper Control Limits: 5.82 Lower Control Limits: 0
As the supervisor in charge of shipping and receiving,you need to determine the average outgoing quality in a plantwhere the known incoming lots from your assembly line havean average defective rate of 3%. Your plan is to sample 80 unitsof every I ,000 in a lo t. The number of defects in the sample isnot to exceed 3. Such a plan provides you with a probabilityof acceptance of each lot of . 79 (79%). What is your averageoutgoing quality?
Construct a 3-sigma X-bar chart for the length in centimeters of a part from the following tabble . What is the upper controt limit? sample observation 1 observation 2 observation 3 observation 4 1 0.486 0.499 0.493 0.511 2 0.499 0.506 0.516 0.494 3 0.496 0.5 0.515 0.488 4 0.495 0.506 0.483 0.487 5 0.472 0.502 0.526 0.469 6 0.473 0.495 0.507 0.493 7 0.495 0.512 0.49 0.471 8 0.525 0.501…
380,000 automotive A-Frame brackets are stamped in a year with a complex process involving shearing, forming, stamping, and heat treating. Each bracket has 6 Critical To Quality features. 627 brackets had at least one defect. Evaluation of the 627 brackets showed a total of, 1191 defects. Calculate the defects per million opportunities (DPMO). Calculate the defects per million (DPM). Calculate the defective units per million (DUPM).
Jim's Outfitters, Inc., makes custom western shirts. The shirts could be flawed in various ways, including flaws in the weave or color of the fabric, loose buttons or decorations, wrong dimensions, and uneven stitches. Jim randomly examined 10 shirts, with the following results shows below. Shirt 1 23456 ∞ 7 8 9 10 Defects 10 05 10 4 9 1 4 5 4 a. Assuming that 10 oberservation are adequate for these purpose, determine the three-sigma control limits for defects per shirt. (what are the UCLC and LCLC) b. Suppose that the next shirt has 12 flaws. What can you say abou the process now?
The optimum level of inspection occurs when we catch at least 98.6 percent of the defects O a. TRUE O b. FALSE JS PAGE FINIS Coa acer F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 z' 图, # & 4. O 6 7 %24 %23 近

Mo. A Pareto analysis would show that the 3rd highest number of defects is