Parvinbhai Water flows into the pipe section on the left-handside marked as Qin in Figure Q3b. There are twosymmetric outlet ports, and the flow is steady. Theinlet and the two outlets are circular pipes withdiameters D1 and D2 as indicated. With D1 = 0.2m and D2 = 0.05m, what flowrate Qin will requirea net force on the pipe section of F = 10N to theright to hold the pipe stationary? Neglect anyfrictional losses in the system and assume constantvelocities across each inlet and outlet. UseMomentum and Bernouli Equation.D₁QinGD₂76₁D₂60°60°

Answered: Image /qna-images/answer/e4f6b33e-416b-4625-a1ad-df6bfc4ee94e.jpg

Answered: side marked as Qin in Figure Q3b. The…

side marked as Qin in Figure Q3b. The symmetric outlet ports, and the flow is inlet and the two outlets are circular pip diameters D1 and D2 as indicated. With

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The three figures below show the mobility Nyquist plots for three systems under a specific dynamic…

A: Given:The Nyquist plot for three systems A, B, and C under a specific dynamic test is given in the…

Q: 32: find the resultant. 20 F₁ = 3N 4m 2 1m F₂=6N Lm 13 N.m

Q: B- A centrifugal fan connected to air duct system, the static losses in the duct is 100 N/m2 and the…

Q: Q₁)A cylindrical resistor element on a circuit board dissipates 0.6 W of power. The resistor is 1.5…

A: Dissipated Power, = 0.6 Wtime, t = 24 hours =243600 = 86400 secondsDiameter, d = 0.4 cm = 0.004…

Q: I need help on this mock question:

A: The objective of the question is to simplify the equations for x- and y-momentum, calculate the…

Q: Working for an engineering consultancy firm, your knowledge of fluid dynamics is required to design…

A: Maximum operating pressure = 0.76 MPa = 760 kPaDiameter of the pipe, d = 150 mm

Q: 4. Working for an engineering consultancy firm, your knowledge of fluid dynamics is required to…

A: Disclaimer from Bartleby:Hello. Since your question has multiple sub-parts, we will solve the first…

Q: How is it that the LHV of wood is higher than the grass? when grass has 15.312MJ/kg and wood has…

A: LHV of woodLHV of grass

Q: Consider a two-dimensional flow which varies in time and is defined by the velocity field, u = 1 and…

A: Given that :Flow is two dimensional flowVelocity field terms are given u=1v=2ytAsking to calculate…

Q: Question: For the frame shown below, the radius of pulley is 0.5 m. a) Draw the free body diagram of…

A: Given:The radius of the pulley is .Concept used:The two component of forces acts at A one in…

Q: The channel shape cross-section and the rectangular cross-section shown in the Figure Q4 are made of…

A: The solution is mentioned below

Q: c) What is the value of tensile strength?

A: The aim of this question is to explain the young modulus value, yield strength from the…

Q: A single-stage axial flow pump with outer radius r2 =0.240 m and inner radius r1=0.120 m is given.…

Q: A three-blade propeller of a diameter of 1.5 m has a rotational speed is 60 Hz, the activity factor…

A: Given:

Q: Consider a two-dimensional flow which varies in time and is defined by the velocity field, u = 1 and…

Q: A 36-KN load P is supported by the three rods below. Determine the following: a. The change in…

Q: 3- A forced circulation boiler delivering 36 kg/s at 130 bar is operated with a circulation ratio of…

Q: Q3 A portable conveyor is to be raised and lowered using the double power screw arrangement as shown…

A: Given:Value of the total load, Design stress of the power screw, Lead angle of the screw,…

Q: Q.11Solve and plot overall block diagram and by using block diagram simplification determined…

Q: Q1:B/( /Gives the functions of the following i 1- Steam Generator in Steam Power Plants. 2-…

A: We will discuss the function of following .

Q: Q3) A 1200-W iron is left on the ironing board with its base exposed to the air. About 85 percent of…

Q: The performance characteristics of a certain centrifugal pump are determined from anexperimental…

A: The objective of the question is to calculate the actual head rise across the pump and estimate the…

Q: For Air Assume: y =1.4 and R = 287 J/kg K Question B1 a) Air is flowing at a Mach number of 0.6 in a…

A: The objective of the question is to calculate the mass flow rate through the duct, the percentage in…

Q: 3 m/s 5 m/s t=2s t = 7 s 1. A particle moves along a horizontal path with its velocity varying with…

Q: can you help me answer this question please, (the secone image) using figure 1? thank you

A: The objective of the question is to apply the boundary conditions and specified forces to the global…

Q: During the 2017 baseball season in a game against the Texas Rangers, Matt Bush (B) and Joey Gallo…

Q: Consider the 2-D incompressible, invisicid Navier-Stokes equation in the horizontal plane. Recall…

A: The objective of the question is to simplify the equations for the x and y momentum, calculate the x…

Q: Two masses m 3.2 kg and my 8.9 kg a massless pulley of radius R 131 cm. r k 12 N/m and equilibrium…

Q: ment x(0)= 0.1 m, and released from sition of the mass after 2 seconds... fter 2 seconds

A: The stiffness of the springMass of the blockInitial displacementIt is released from the rest so the…

Q: What is the mass of the bug?

Q: A centrifugal pump having a head-capacity relationship given by the equation ha=180 – 6.10 X 10-4 Q2…

Q: A local shop is maintained at 101.3 kPa and 19oC. The air inside the shop is forced to leave at a…

Q: 25/A- Airbus 320 fly in steady level flight with altitude 10.5 km and the density at this level…

Q: You are asked to design piping systems of two different lengths of 0.75 and 1 km respectively for…

A: Given:

Q: Figure 2 show Engineering Stress-Strain diagram of a moderately ductile metal. Young's Modulus, E is…

A: Figure 2 show Engineering Stress-Strain diagram of a moderately ductile metal. Young'sModulus, E is…

Q: Calculate the horizontal reaction at support 0 of 15 kg slender rod which is rotating at constant…

A: Calculate the horizontal reaction at support O. If m = 15 kg slender rod which is rotating at…

Q: Question 4: T shape homogeneous bar m=50 kg mass. Compute the reaction at the pin O just after the…

A: Mass of the T-shape homogeneous bar,

Q: The physical realization of a system to control liquied liver is shown in figure below Draw the…

Q: A propped cantilever beam is loaded by a bending moment of the magnitude ?_? at the point B as shown…

A: The objective of the question is to calculate the reaction forces at points A and B, and the…

Q: For Air Assume: v=1.46×10 -5 m²/s and p = 1.225 kg/m³ Question A1 A flat plate with unit width is…

Q: A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 130 KN,…

A: A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 130…

Q: Using the provided data: cross-section width w = 19 mm, cross-section hight h = 92 mm, length of the…

Q: 1. A 10 mm steel plate is welded on a wider steel plate as shown. The weld leg, w = 12 mm. Find the…

Q: nces between mass and area moment of im

A: The inertia is the state of an object which resists the change in the state. Inertia is classified…

Q: D-H Parameters Table for the 3 DOF RPR manipulator is given in the Table (Classical type) Linki 0 d₁…

A: Given:To find:Determine the joint variables.

Q: 1- Two mass-spring-damper systems A & B. System A has = 0.1 and wn = 20 rad/sec, and system B has =…

A: Here we will apply the damping coefficient comparison

Q: A collar of mass m slides without friction on a horizontal rigid rod and is restrained by a pair of…

A: Given:

Q: h 0 a) How far down the slope will they land? r b) How long will they be in the air? t Vo m at an…

Q: Consider the bar in Figure 2, which has cross-sectional area A = 1·10−3 m2, modulus of elasticity E…

Q: describe the importance of setting an effective handling system and or approach for mobilisation of…

A: Setting an effective handling system in a polymer production facility is crucial for optimizing…

Concept explainers

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.

Question

Parvinbhai

Water flows into the pipe section on the left-hand
side marked as Qin in Figure Q3b. There are two
symmetric outlet ports, and the flow is steady. The
inlet and the two outlets are circular pipes with
diameters D1 and D2 as indicated. With D1 = 0.2
m and D2 = 0.05m, what flowrate Qin will require
a net force on the pipe section of F = 10N to the
right to hold the pipe stationary? Neglect any
frictional losses in the system and assume constant
velocities across each inlet and outlet. Use
Momentum and Bernouli Equation.
D₁
Qin
G
D₂
76₁
D₂
60°
60°

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Write the given data with suitable variables-

VIEW

Step 2: Determine the value of flow rate.

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The branched pipe as shown in figure below discharges water. The diameters of the pipe 1 is 1.5 cm, pipe 2 is 3 cm & pipe 3 is 4 cm. The discharges in pipe 1 is 21 lit/sec, pipe 2 is 26.25 lit/sec. Find the discharge in pipe3 in Lt/sec, velocity in pipe 2 m/s & velocity in pipe 3 if the diameter of pipe 3 is 4 cm. (ENTER ONLY THE VALUE IN THE BOXES BY REFERRING THE UNIT GIVEN IN BRACKET. ALSO UPLOAD YOUR HAND WRITTEN ANSWERS IN THE LINK PROVIDED) Pipe 1 Pipe 3 Pipe 2 The discharge in pipe 3 (in Liter/sec) = The velocity of water in pipe 2 (in m/s) = The velocity of water in pipe 3 (in m/s) =
a) Hydraulic systems commonly have a pump that produces a constant flow rate. Assuming the fluid is incompressible, this situation is known as steady flow or continuity flow. Referring to Figure Q3 (c) the fluid flows at a velocity of 3 m/min at point Q1. The diameter at point Q1 is 50 mm and the diameter at point 2 is 40 mm. In applying the continuity equations, determine the flow velocity at point Q2. Further determine the flow rate in g.p.m (gallon per minute), given 1 gallon = 0.00378 m³. Figure Q3 (c)
:00 Time LeiL HAM YAHIA ZARARIA ALY MOUSTAFA: Attempt 1 15 m 3 6. 6 m 6 m Elbow 6 m 3 m 1 DELL
Find F(1) OF THE LAPALCE TRANFORM FUNCTION
4. FLUID FLOW 1. The figure below shows a water tank with piping system for a small manufacturing plant. If water flows through the system ((A) at 40 L/s, what would be the pressure at point B? The water has a density of 998 kg per cubic meter and viscosity of 0.8 centipoise. measures 0.04089 m and 0.04826 m in inside and outside diameter, respectively. The tank is exposed to the atmosphere The 1.5 inches (nominal) wrought iron pipe Given: Q= 40L/s = 0.040 m/s p= 998 kg/m H=0.8 centipoise 0.001P-s = 0.08 P-S Reg'd: Pressure at B. = ? 1 cp i.d. = 0.04089 m o.d. = 0.04826 m length of pipe = 110 m
Fluid: Consider the following two tank system, where an input flow enters the first tank with flowrate Qri and travels through a pipe of fluid resistance Rf to fill up the second tank. The fluid then flows out of the second tank through an orifice governed by the square-root orifice equation for pressure drop, Qf,0 = k(Pza). Find the linearized system equations written in terms of pressure. Note that P1 and P2 are pressures relative to atmospheric pressure (not absolute pressures) Qti Pa = constant C1, P, R, C+2, P2 k Q1
Problem 3: Leaking Tank Your engineering firm has been asked to determine whether the secondary clarifier (labeled "SECONDARY") downstream from the aeration basin (labeled "AERATION") is leaking at your local wastewater treatment plant. You conduct measurements over 45 minutes. During this time, you determine the average inflow rate Qin = 4.5 m³/min, the average outflow rate Qout = 4.0 m³/min, and the change in volume in the secondary clarifier is AV = 2.2 m³. You also determine that the fluid removed from the aeration basin is 90% water and 10% air by volume, since the fluid contains air bubbles. These bubbles rapidly dissipate in the secondary clarifier. PRETREATMENT OVERFLOW SECONDARY SLUDGE DIGESTION TRASH DRYER AERATION AIR PRIMARY DRY SLUDGE FINISHING ALICANTOY Is the secondary clarifier leaking, and if so, at what rate? [kg/min] SCUM METHANE
Q: for the following equation, what are the units of x., u, and a if X, is the distance in m. t, is the time in second? [X. x3 = + u?t +
Q. For the Shown mechani l system, Find Hthe reledion between F and X Youd Xx Then draw the block diagram. M, K, MA K2
Q3) The path of a projectile is shown in figure (3). If the object has an initial velocity of Vo-30 m/s that is perpendicular to the slope, determine d? wwwwwamangu Vo=30m/s
FIND THE DIFFERENTIAL EQUATION FOR THE SYSTEM No fuctioi Mz
В 0,= 10 rad/s A04=10" A2, A3, A4 AO2=4" 0204=12" 3 AB= 3" Find VA, VA, VB and m4 4 O4 O4