Q2/ Use the unit load method to find the slope and the horizontal displacement of point C on the frame shown below. E-200 GPa, I=200 x 10° mm 5 m B C 4 kN El 2 kN/m 6 m 1.5 El A For real load, horizontal reaction Ax= * Your answer For real load, vertical reaction Ay= * Your answer For real load, vertical reaction Cy= * Your answer

Q2/ Use the unit load method to find the slope and the horizontal displacement of point C on the frame shown below. E-200 GPa, I=200 x 10° mm 5 m B C 4 kN El 2 kN/m 6 m 1.5 El A For real load, horizontal reaction Ax= * Your answer For real load, vertical reaction Ay= * Your answer For real load, vertical reaction Cy= * Your answer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 5 Find the supportive force system for the cantilever beam shown pinned at C. Given data: Point load, Not yet answered P=380 N and distributed load, w=80 N/m. Marked out of 5.00 on 7 m 2 m A 5 m- 5 m- Supportive force system Ax= Ay= Сх- N Су- By= N
A part of the structure for a facory automation system is a beam that spans 30.0 inches as shown below. Loads that are applied at two points each 8.0inches from a support. The left load F1=1800 lb remains constantly applied while the right load F2=1800 lb is applied and removed frequently as the machine cycles. Find the following: Maximum stress Minimum stress Mean stress Alternating stress Stress ratio Solve the missing parameters in complete solution put necessary diagrams if needed. Thanks
W LAB B LBC assume w = 4 kips/ft P= 5kips LAB=16 ft C LBC=8 ft What is the vertical reaction at A ? answer in kips
1. A tripod shawn supports of note that ball and rocket joints are used to mount the tripuod a load P=1000N at point A. Take at points B,D, and C. consider the t LI L 2 L2: 4 L3 : 3 A : 45° g :30° %3D on x-z plane L2 POINT C (2,-2,3) C0,0,0) ミー- Determine the ff Force of AB - N Force of AC - N Force of AD : N
Calculate the reaction forces on the bearing near the pulley and bearing at the far end of the shaft. Include a free body diagram and coordinates. Given the shaft length is 1 meter= Mass=40Kg Static load = 8600N Dynamic (running load) = 8400N Some hints:1. This solution will require you to draw known forces and find unknown reactions in 2perpendicular planes and then add the horizontal and vertical reaction forces asvectors to find the reaction force (hypotenuse).2. Bearings are usually mounted as near as possible to the ends of the shaft withoutfouling the other machine elements. The bearing at the far shaft end can be mountedat the 1 meter point. The bearing at the pulley end should allow clearance to assemblethe pulley.3. Bearing reaction forces are typically simplified as a single point load through thebearing centre.
=, Try to use the first processing method to solve the equivalent load vector of the illustrated structure. Known q =2 kN/m, F, =8kN, 1= 5 m.
Q: For the spring system shown in the accompanying figure, determine the displacement of each node. Start by identifying the size of the global matrix. Write down elemental stiffness matrices, and show the position of each elemental matrix in the global matrix. Apply the boundary conditions and loads. Solve the set of linear equations. Also, compute the reaction forces. k2 = 9 lb k1 = 20b in 20 lb k,=5 lb ww lb in kz = 5 lb in ks = 9 in lb k6 = 9 in 50 lb k4 = 20 lb kg = 20 b in in
Application of Equilibrium Solve for the value of unknown variables Given : P1 = 6.85 KN P2 = 4.65 KN W1 = 6.15 KN/m Unknowns : RAy , RAx ,RBy , MA What is the value of internal shear 2.50m to the right of support A
The dimensions are of the graph are d1 = 7 cm , L1 = 6 m , d2 = 4.2 cm , and L2 = 5 m with applied loads F1 = 130 kN and F2 = 60 kN . The modulus of elasticity is E = 80 GPa . Use the following steps to find the deflection at point D. Point B is halfway between points A and C. What is the reaction force at A? Let a positive reaction force be to the right.
Live load on the deck = 70 psf Deck weight = 6 psf Beam weight = 8 lb/ft Column weight = 80 lb Please round to the nearest one. Foundation reaction at 2-A column= lb 16' 2 12' Time left 0:33:26 3
Required information Stairs leading to a balcony are shown below. |400 lb dimensions in inches 40° 144 600 lb 32 22 16 38 30 30 For the 400 lb and 600 lb forces, and if F= 155 lb and P= 0, determine the reaction at point Dand the force supported by bar BE. The reaction at point Dand the force supported by bar BE are as follows: Dy= 410 Ib TBE = - 701.798 Ib
Problem 2: Review of Statics & Mechanics Consider the beam below. The beam has a pin support on the left and a roller support at the right. The beam is loaded by two point loads of 15 and 7.5 kN, respectively. The beam has the cross- section shown on the right. 15 kN 7.5 kN 20 mm: 150 mm Centroid 20 mm |C 150 mm 1.5 m 1.5 m-+1.5 m 1.5 m- 20 mm -250 mm- a. Find the support reactions at A and B. b. Determine the axial force, shear force, and moment at point C. c. The beam has the I-shaped cross-section provided above. Determine the maximum stress due to bending at point C. Sketch the bending stress distribution over the cross-section at point C, indicating the value at point b as well as any maxima and minima.