Q- .................It is produced from the addition of water to the gypsum and may be added to the aggregates It may be hollow or solid.Used to build non-load internal parries and to covering steel parts to increase fire resistance. O Gypsum Blocks O Non of them Normal burn brick Adobe O Concrete blocks

Q- .................It is produced from the addition of water to the gypsum and may be added to the aggregates It may be hollow or solid.Used to build non-load internal parries and to covering steel parts to increase fire resistance. O Gypsum Blocks O Non of them Normal burn brick Adobe O Concrete blocks

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter13: Materials Processing

Section: Chapter Questions

Problem 10ETSQ

See similar textbooks

Similar questions

Q2) Fill the blank with suitable word or words: 1) The main types of cast iron are....... ... and ...... 2) There are three main reactions in Iron-Carbon phase diagram, theses are.... are the main stages of annealing heat treatment process. 3) ****** ***** ****** and ****** ....... and
Fill in the blanks with appropriate words a) Fibers are not ……………………… Therefore heat is only necessary for consolidation ofthe resin.b) ……………………….. is the reduction in the dimensions caused by thermal contraction ofthe polymerc)................................. is applied to the the surface of mold for easy removal of the part
Harmful substance in aggregate caused steel bars deterioration is O Clay O gypsum O lead salts reaction O Other:
The the size of the 5 points aggregate, the--------- is the surface area and hence --amount of water is required for wetting the surface and less matrix or paste is required for lubricating the surface to- - internal friction. For a given quantity of water and paste, bigger size of aggregates will give higher workability. The above, of course will be true within certain limits. * High, less, reduction, improve. More, high, reduction, improve. None of them. High, less, reduction, worst.
This equipment is typically used in cement manufacture and is essentially a long continuous rotating tube heated to high temperatures. a. Rotary kiln b. Blast furnace c. Shell and tube heat exchanger d. Smelter
A circular beam is loaded and supported as shown below. The material used to make the beam has a maximum allowable bending stress of allow= 125 MPa. π Recall that the second moment of area for a circle is - 4 W Use the following values in your working out: 4 (9)** L L = 22 m d = 16 cm Old a) Draw the FBD, SFD and BMD for the beam b) Write an expression for the internal bending moment as a function of length. Clearly show what convention you're using for positive length. c) Determine the maximum allowable intensity of w. d) Draw the approximate bending moment diagram for the beam shown below. You are welcome to either use symbolic variables or estimate loads/dimensions. Clearly write all assumptions.
(a) In general, which provides better fire performance, carbonate or silicate aggregates? Why? (b) Why does fire design incorporate a load reduction factor (Dfire) = 1.0? (c) Two identical beams (Beam 1 is simply supported, and Beam 2 is fully restrained) are heated under similar conditions. What does the mechanical strain equal to in each of these beams? (d) A design office located in Clemson, SC (with a branch in San Francisco, CA) envisions designing a new composite member made of steel and timber. This to-be designed member is expected to be used in wildfire-prone regions primarily for single family homes. Comment on how you would design such a member to achieve superior fire performance. (e) Plot and discuss the expected degradation faces in three bending elements (say, beams) to be made from concrete, steel and timber?
a. For structural support of sand mold which part or component is necessary in sand casting? In absence of that component how the casting can be done, explain. b. Mention the reason for heating the pattern at 175-360 deg C in shell moulding process c. Describe utility of thin plastic sheets in V-process.ANSWER ALL THE THREE PARTS PROPERLY
be can Haw mineral oF
In pressure grouting technique, the slurry contains * O PFA O microsilica all of the mentioned O cement
Bricks must be . with . before use to decrease the soluble salts inside the bricks الجواب
Pick the correct statement regarding welding. O a. More Noise during welding O b. Welding process is slower O c. 100 % efficiency can be achieved in welding connection O d. Holes are drilled in welding connection