Problem 3: Aerodynamics Consider a UPS delivery van. Part A Is this vehicle streamlined? (yes/no) www Part B Which drag force will be dominant, friction drag or pressure drag, and why? (<25 words) Part C By what percentage does the speed increase from 55 to 75 mph? [%] Centr Part D By what percentage does the drag force increase from 55 to 75 mph? Assume air as given by the ICAO standard atmosphere at an elevation of 5,000 ft. Assume the aerodynamics of the truck can be predicted by a disk with diameter 9.0 ft.

Problem 3: Aerodynamics Consider a UPS delivery van. Part A Is this vehicle streamlined? (yes/no) www Part B Which drag force will be dominant, friction drag or pressure drag, and why? (<25 words) Part C By what percentage does the speed increase from 55 to 75 mph? [%] Centr Part D By what percentage does the drag force increase from 55 to 75 mph? Assume air as given by the ICAO standard atmosphere at an elevation of 5,000 ft. Assume the aerodynamics of the truck can be predicted by a disk with diameter 9.0 ft.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If your lift to drag ratio is 15 for airline A flight and the airplane weighs 15,000-lb for L/Dmax, what’s the speed for L/Dmax at 22,500 lbs.?
FLUID DYNAMICS (AERO) Complete solution, units and fbd if possible Required to find: 1. ) CL ( Coefficient of lift ) and 2.) Thickness Ratio of airfoil UP VOTE<<
= 3570 T AC =144 Example: 1.5 ft It is desired to determine the drag force at a given speed on a prototype sailboat hull. A model is placed in a test channel and three cables are used to align its bow on the channel centerline. For a given speed, the tension is 40 lb in cable AB and 60 lb in cable AE. Flow 4 ft Determine the drag force exerted on the hull and the tension in cable AC. Choc ug the h- as the free hod- DApress the
"lin' 2. In an undistur bed airstream, where the presure is 14.7 and the semperature is 519 °R the vélocity #kec what are the velocity , density j 600 the presure is 13.9 10/in2? temperature, and speed of sound where
Question 3 The aerodynamic derivative X, may be determined from the following expression: X -pU SCD %3D where p is the air density, S is the wing area, U is the airspeed, and Cp is the drag coefficient. Consider an aircraft of weight 68 kN and wing area 43 m?, flying straight and level under international standard atmosphere (ISA) conditions, where p 1.018 kg/m, at an airspeed of 155 m/s. The aircraft %3D has a drag polar Cp = 0.011 + where Ci is the lift coefficient. Calculate the value of X, at this flight condition. Give your answer in units of Ns/m.
2- Air (v = 1.8×10° m²/s) flows along a flat plate with a velocity of 150 km/hr. How long does the plate have to be to obtain a laminar boundary layer thickness of 8 mm. %3D [6.146 m]
Problem 3: Let's say you want to predict the aerodynamic drag of a new car based on the use of a model that is one- fifth scale of the actual car/prototype car. We want to predict the drag of the car when it has wind velocity 75 miles/hour with an air temperature of 40°C. The model is placed in a wind tunnel at 10°C. Determine the wind tunnel velocity necessary to achieve similarity between the model and the prototype.
Problem 1: Streamlining From dimensional analysis, we know the drag force is FD- CopAV2/2, where Cp is a dimensionless coefficient of drag. The two space shuttles below have the same area A, the same velocity V, and are flying through the same air. Which has a smaller Co and why? (<25 words) thine e
QH03: Aerodynamic Model: - Circular Disk Page 1 o Inside Dia = 40 mm Outside Dia = 80 mm • Angle of Attack= 15 Degree • Lift Force= 0.38 N • Drag Force=0.40 N • Wind Velocity= 20 m/sec • Air Temperature= 30 C (Note: Take Air Density at 30 C) Required: - Find Lift and Drag Coefficient at 15 Degree Attack Angle.
5.7 The rectangular roof sheet of a kennel has a dimension of 6m x 2m. Calculate the drag force on its upper surface if the wind is blowing parallel to its length at 3m/s. The density and the kinematic viscosity of air are 1.2 kg/m³ and 1.6 x 10-3 m/s, respectively. [Ans: 0.195 N]
04) Define the boundary layer, then find the thickness of boundary layer, shear stress, drag force and coefficient of drag in terms of Re for the velocity profile of laminar boundary layer u/U-4(y/6)-6(y/ö)5. Calculate the boundary layer thickness and drag force if the air flows over a sharp edged flat plate Im long and 0.5m wide at a velocity 0.9m/s, the air density 1.23 kg/m³ and the kinematic viscosity is 1.46*10-³ m/s².
4. The Wright brothers used a very thin wing on their 1903 flyer. In addition, they made extensive use of a homebuilt wind tunnel to test their wing designs. span, b chord, c Model of Wright Flyer (a) The Wright's wind-tunnel models had chord length, c, of about 0.04 m and wing span (length) of 0.26 m. The wind tunnel operated at approximately the same wind speed as the full-scale aircraft - about 13 m/s. Estimate the drag (friction) of a single wind-tunnel model wing under standard conditions (o = 1.225 kg/m³, = 1.7894 x 10-³ kg/s-m). Note that the wing is mounted in the wind tunnel so that both upper and lower surfaces are exposed to the flow. (b) The full-scale 1903 flyer had a chord length of 1.9 m and a wing span of 12.3 m. Estimate the drag (friction) of a single full-scale Wright flyer wing flying at 13 m/s under standard atmospheric conditions. (c) Consider the main wing configuration, which consisted of two wing surfaces (biplane) connected by 18¹ cylindrical rods. We will…