This question about Transportation Engineering Problem Set 3: Vertical AlignmentPart A: Route SurveyingProblem 1:From the vertical curve data given in the sketch below, calculate the values of G1 & G2.Elev@ PVI = 240.5 mProblem 2:Elev PVC = 236.98 mElev@PVT= 236.62 mL = 360 m

Given data, Elev PVI=elevation of Point of vertical intersection = 240.5 m Elev PVC =elevation of…

Answered: Problem 1: From the vertical curve data…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please solve this question yield line method
Problem 2: The cross-section notes shown below are for a ground excavation for a 10-m wide roadway. Sta 16+100 8.20L 13.65R +2.15 +3.50 +5.80 What is the cross-sectional area at Sta 16+100. A. 64.1125 m² B. 46.1125 m2 C. 58.1125 m? D. 52.1125 m2
It is desired to determine the area of the sand bar by the indicated short offsets which were measured on both sides of a baseline AB. a. Determine the area by trapezoidal rule. b. Determine the area by Simpson's one third rule. c. Determine the difference between the areas computed by the two methods. 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.0 4.0 4.0 4.0 4.0 4.0
QUESTION 10 A cutting is to be formed on a straight section of a proposed road. The values of eight consecutive cross sectional areas taken at a constant horizontal distance interval of 20m are 325m², 398m², 456m², 580m², 634m², 546m², 447m² and 362m² respectively. Calculate the volume contained between the first and last cross section using : a. End areas method b. Prismoidal formula
Compute the area of cross-section if the formation width is 12 m, side slopes are 1 to 1, average height along the center line is 5 m, and the transverse slope of the ground is 10 to 1. (Round off your answer to three decimal places).
Describe about the Basis of slope stability analysis by method of slices.
5. A cutting is to be formed on a section of a proposed road. Calculate the volume of cut required to form the cutting between chainages 1000m and 1090m by using : a. End areas method b. Prismoidal formula 1010 172.5 CH 1000 1020 1060 1030 177.5 1040 1050 1070 185.5 1080 1090 A(m) 175.6 175.5 178.5 176.5 190.5 188.5 191.5
7. From the following set of notes, estimate the cross-sectional area: 2.52 3.42 4.1 5.2 5.8 5.52 3 0 4.68 8.8 The roadwidth/formation width is 6 m and the side slope is 1:1. Calculate the area of the cross section.
The earthworks data of a proposed highway shown on the tabulated data. Length of economic haul = 450 m Stationing of limits of economic haul = 2+498.03 and 2+948.03 Stationing of limits of free haul 2+713.12 and 2+763.12 Free haul distance is 50 m. Assume the ground surface to be uniformly sloping. Area Station Cut Fill 2+440 50 m2 2+740 0. Balancing Point 70 m2 3+040 a) Compute the overhaul volume. b) Compute the volume of waste. c) Compute the volume of borrow.
Q#1: A profile levelling is carried out and consecutive readings were observed on staff rod along a chain line at common interval of 10 meter which are listed below in table. First reading is taken on bench mark of 105.615 meter reduce level. Station Points Chainage (m) Staff Readings (m) Remarks BS IS FS 1 00 3.005 BM 2 10 2.285 3 20 1.560 4 30 1.785 5 40 2.105 6 50 2.875 3.105 CP 1 X 53.35 3.465 7 60 3.955 8 70 3.120 9 80 3.015 10 90 2.580 11 100 1.955 CP 2 Determine the reduce levels of all points using both line of collimation and rise and fall method. (Present your answer in table form).
In a proposed highway undergoing road earthworks, the given roadway cross-section notes are as follows:STA 20 + 100 3.00 1.50 1.00-8.50 0.00 6.50STA 20+ 300 2.20 1.20 2.60-7.70 0.00 8.10Width of the roadway is to be determined using side slope of xH:1V where x is the unknown horizontal sideof the slope. Show and draw plotted points of the cross-section of roadway each station. Calculate thefollowing:1. Total number of man-days to finish the earthwork job2. Total cost of machine rentals to finish the earthwork job.In the inventory of available heavy equipment on site are three (3) hydraulic excavators with bucket payloadcapacity each of 0.76m3 and one (1) hydraulic excavator with bucket payload capacity of 1.15m3. The hourlyproduction of each excavator with 100% efficiency are 149m3 and 196m3 respectively. Daily machine rentalfees for smaller capacity is 1,200 pesos while bigger capacity costs 2,200 pesos. Daily machine operationsis limited to 8 hours.
A traverse line was measured in three sections: 295.85 m at slope 8°45’, 149.58 m at 4°29’, and 373.48 m at slope 4°23’. Determine the horizontal length of the line. Draw the figure and show the complete solution. Provide a recheck of the answers.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Problem 1: From the vertical curve data given in the sketch below, calculate the values of G1 & G2. Elev @ PVI = 240.5 m Problem 2: Elev PVC = 236.98 m Elev@ PVT= 236.62 m L = 360 m