Overall efficiency of a centrifugal pump is the ratio of a. Energy available at the impeller to the energy supplied to the pump by the prime mover b. Actual work done by the pump to the energy supplied to the pump by the prime mover c. Energy supplied to the pump to the energy available at the impeller d. Manometric head to the energy supplied by the impeller per Newton of water

Overall efficiency of a centrifugal pump is the ratio of a. Energy available at the impeller to the energy supplied to the pump by the prime mover b. Actual work done by the pump to the energy supplied to the pump by the prime mover c. Energy supplied to the pump to the energy available at the impeller d. Manometric head to the energy supplied by the impeller per Newton of water

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter33: Hydronic Heat

Section: Chapter Questions

Problem 24RQ: In a primary-secondary pumping arrangement, the largest circulator pump will be located A. in the...

See similar textbooks

Similar questions

Pumps are rated by its maximum O a. Operating pressure and output flow only O b. pressure and speed only O C. pressure, speed and flow. O d. output flow and speed in rpm only
Which of the following is acting on the fluid in a Vane Pump? a. Centripetal Force b. Centrifugal Force c. Tangential Force d. Shear Force
Explain the working principle and applications of a centrifugal pump in the context of mechanical engineering.
In a centrifugal pump, the liquid enters the pump a. At the centre b. At the bottom c. At the top d. From sidess:
1. Two pumps are connected in parallel, if Q1 is the discharge of pump 1 and Q2 is the discharge of pump 2, where Q2 > Q1, what is the discharge?A. Q1B. Q1 + Q2 c. Q2D. Q1-Q2 2. If Hi is the indicated horsepower and HB is the indicated brake horsepower of a compressor, then what is mechanical eficiency, Em, equal to? A. Em = HB/HiB. Em = Hi/HBC. Em = HB - HiD. Em = Hi -HB
The specific speed (nq) of a pump provides information… a. on the expected revolution number of the driving motor. b. on the number of blades. c. on the circumferential velocity of the impeller. d. on the shape (type) of the impeller (axial, radial or mixed).
If a certain centrifugal pump generates 50 meters of head pumping water with a 1.0 specific gravity, how much head does it generate pumping sulfuric acid with a 1.82 specific gravity? (assuming the driver is powerful enough to handle it)
. Two identical cylinders are applied in series as shown in Fig.2. The cylinder piston and rod diameters are 80 mm and 40 mm respectively. The valve is working in position 2. Assuming the tank pressure is 1Bar. . In order to lift the mass 3000 kg in velocity of 0.1m/s, how much pressure in MPa are needed from the motor? • How much volume in liter/min are needed from the motor? 24p CA. ZAP Tips: Q=C₂4 P2 A2 P1 A1 A2 A1 Q1 Q2 MIHIXM Q3
what the Procedure of this experiment ? Experiment Title: Performance of a Centrifugal Pump.
A Large wind turbine has blade span diameters of 110 m. It sits high off the ground where the average wind speed is 7 m/s. Assume the air density to be 1.25 kg/m3, and the efficiency of the wind turbine, its generator and its electric grid synchronization device is 26%. What is the average electric power that this turbine can output to the grid? a. Sketch the problem. b.Draw lines identifying the control volume, or control mass. c.Identify the states with numbers, letters, or descriptions such as “in” and “out”. d.Write down the knowns and unknowns. e.Identify what is being asked for. f.State all assumptions.
With reference to the momentum balance, which of the following sentences is correct? A. The momentum balance is the balance of forces within the control volume. B. The momentum balance equation is a scalar equation. C. For a pipe with a 90o reducing bend, an increase of the pressure at the inlet causes an increase of the vertical component of the force. D. For the flow through an orifice, the value of the exit velocity from the orifice depends upon the diameter of the orifice. Please write just a little about wrong options also, thanks!
2. Determine the water horsepower and the mechanical efficiency of a centrifugal water pump which has an input of 2611 watts, if the pump has an 8 in.nominal size suction and 6 in.nominal size discharge and handles 150 gpm of water at 150 deg.F (specific volume is 0.01634 ft3/Ibm). The suction line gage shows 4 in.Hg vacuum, and the discharge gage shows 26 psi. The discharge gage is located 2 ft above the center of the discharge pipe line and the pump inlet and discharge lines are at the same elevation.