ou construct 4 resistors with the following specification: • R1 is made out 33.84 meters of aluminum wire with a diameter of 0.1500mm. • R2 is made out 14.52 meters of tungsten wire with a diameter of 0.1500mm. • R3 is made out 39.04 meters of copper wire with a diameter of 0.1500mm. • R4 is made out 5.137 meters of an unknown wire with a diameter of 0.1500mm. ou then arrange the four resistors as shown below. The voltages are indicated so that R1, R2, and R3 have a voltage drop of 18.00V and the resistor R4 has a voltage drop of 00V. What is the metal used to construct resistor R4? 24.00 V 6.00 V ww R1 R2 ww R3 #1 R4 BAT1 0.00 V

ou construct 4 resistors with the following specification: • R1 is made out 33.84 meters of aluminum wire with a diameter of 0.1500mm. • R2 is made out 14.52 meters of tungsten wire with a diameter of 0.1500mm. • R3 is made out 39.04 meters of copper wire with a diameter of 0.1500mm. • R4 is made out 5.137 meters of an unknown wire with a diameter of 0.1500mm. ou then arrange the four resistors as shown below. The voltages are indicated so that R1, R2, and R3 have a voltage drop of 18.00V and the resistor R4 has a voltage drop of 00V. What is the metal used to construct resistor R4? 24.00 V 6.00 V ww R1 R2 ww R3 #1 R4 BAT1 0.00 V

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter17: Current And Resistance

Section: Chapter Questions

Problem 66AP: When a straight wire is heated, its resistance changes according to the equation R = R0 [1 + (T ...

See similar textbooks

Similar questions

-gauge copper wire has a diameter of 9.266 mm. Calculate the power loss in a kilometer of such wire when it carries 1.00102 A.
(a) Digital medical thermometers determine temperature by measuring the resistance of a semiconductor device called a thermistor (which has a= - 0.0600/°C ) when it is at the same temperature as the patient. What is a patient's temperature if the thermistor’s resistance at that temperature is 82.0% of its value at 37.0°C (normal body temperature)? (b) The negative value for a may not be maintained for very low temperatures. Discuss why and whether this is the case here. (Hint: Resistance can’t become negative.)
When a straight wire is heated, its resistance changes according to the equation R = R0 [1 + (T T0)] (Eq. 17.7), where is the temperature coefficient of resistivity. (a) Show that a more precise result, which includes the length and area of a wire change when it is heated, is R=R0[1+(TT0)][1+(TT0)][1+2(TT0)] where is the coefficient of linear expansion. (See Topic 10.) (b) Compare the two results for a 2.00-m-long copper wire of radius 0.100 mm, starting at 20.0C and heated to 100.0C.
When a straight wire is heated, its resistance changes according to the equation R = R0 [1 + (T T0)] (Eq. 17.7), where is the temperature coefficient of resistivity. (a) Show that a more precise result, which includes the length and area of a wire change when it is heated, is R=R0[1+(TT0)][1+(TT0)][1+2(TT0)] where is the coefficient of linear expansion. (See Topic 10.) (b) Compare the two results for a 2.00-m-long copper wire of radius 0.100 mm, starting at 20.0C and heated to 100.0C.
Material=Nickel Resistivity=6.99 x 10^(-8) Ω.m a) Calculate the conductivity of your material. Compare the conductivity of your material with conductivity of glass having a resistivity of 3.0 x 1010 Ω.m. b) Suppose that you have a cylinder that is made of your material with a length of l=20.0 cm and a cross- sectional area of A=4.00x10-4 m2. Calculate the resistance, R, of the cylinder. c) A 9.0-V battery is connected to the cylinder that is made of your material in part-b. Using Ohm’s law calculate the current passing through the material. (V=I*R I=?)d) Suppose that the cylinder in part-b is cut into four equal pieces. Calculate the resistance of one piece of cylinder (which has a length of one fourth of the original length l) and compare your result with the originalcylinder with length l.
Content Next > 10:19 PM 4/19/2023 x ⠀
a)(QUESTION 2) Determine the length (in mm) of a gold conductor that has a resistance of 0.018 Ω and a cross-sectional area of 3.4 x 10-9 m2. The resistivity of gold is 2.2 x 10-8 Ω-m b) An aluminum conductor with the same length and area as in Question 2 above would have a higher resistance than the gold conductor. The resistivity of aluminum is 2.6 x 10-8 Ω-m. True or False?
V1 1] Consider the circuit in the diagram with an unknown resistor R. The known resistor is R₁ = 1k, the power supply voltage is V, 12 Volts, and the measured output voltage is Vx8 Volts. Multisim insists on values, so I put -10 for the 12V unknown. I'll try to take this approach consistently in the homework diagrams, if possible. A) Determine the value of R. B) Determine the current i through the resistors. C) Determine the total power P supplied by the power supply. Hilt R1 ww 1kQ www Rx -122 XMM1 to is
Material= Lead Resistivity (Ω.m) = 22 x 10- 8 a) Calculate the conductivity of your material. Compare the conductivity of your material with conductivity of glass having a resistivity of 3.0 x 1010 Ω.m. b) Suppose that you have a cylinder that is made of your material with a length of l=20.0 cm and a crosssectional area of A=4.00x10-4 m2 . Calculate the resistance, R, of the cylinder. c) A 9.0-V battery is connected to the cylinder that is made of your material in part-b. Using Ohm’s law calculate the current passing through the material. (V=I*R I=?) d) Suppose that the cylinder in part-b is cut into four equal pieces. Calculate the resistance of one piece of cylinder (which has a length of one fourth of the original length l) and compare your result with the original cylinder with length l.
Question 2 : A. Estimate the voltage drop for A solar array has been installed and the distance between the output of the array and the solar controller is 10 metres. The short circuit current of the array is 9.6A. • The cable has a cross sectional area of 10 mm2 • The cable is copper with a resistivity of 0.0183 ohms/metres/mm2 • The battery voltage of the system is 12V.
What is the equivalent resistor between the terminals a and b if you replace R1 by 20 Ohm and R2 by 40 Ohm ? This combination of resistors goes to infinity by repeating itself. Write your answer in units of Ohm. No decimal points is necessary. Maximum od 4% of error is accepted in your answer. R1 R, R2 R2 b. R1 R,
Question A2 Pure copper has a resistivity of 1.68 x 10-8 Nm. Some accurate cubes of copper are prepared, and electrical measurements are made, for which current is passed across a pair of opposite faces. a) Comparing a 2.5 cm cube and a 5 cm cube, which will have the higher conductance? Ex- plain your answer. b) Given eight 1 cm cubes, how can they be stacked to get the highest and the lowest resis- tance between opposite faces of the stack? Calculate the resistance of each stack.