If u is unknown, using Michel's formula for transition, find the value of u₁ =10_cal such that both separation and transition occur at the point of separation. (i.e. the two points are co-located.) When, u₁ >10_col, state whether the transition point x,, is upstream (towards the leading edge) or downstream (towards the trailing edge) of the point where separation occurs? Take the kinematic viscosity to be: v=1.5×105 m²/s. Neglecting freestream turbulence, the decelerating freestream velocity profile over a flat plate is given by, u=u₁ (1-x/L)", with L = 10m.

If u is unknown, using Michel's formula for transition, find the value of u₁ =10_cal such that both separation and transition occur at the point of separation. (i.e. the two points are co-located.) When, u₁ >10_col, state whether the transition point x,, is upstream (towards the leading edge) or downstream (towards the trailing edge) of the point where separation occurs? Take the kinematic viscosity to be: v=1.5×105 m²/s. Neglecting freestream turbulence, the decelerating freestream velocity profile over a flat plate is given by, u=u₁ (1-x/L)", with L = 10m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2) Discuss the importance of boundary layer approximation in finding the solution of fluid flow problems.
A 20degC water flows to 50cmx60cm flat plate with velocity of 3m/s . The flat plate surface temperature is maintained at 40deg C. The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? Round your answer to 2 decimal places.
If a vertical wall at temperature T, is surrounded by a fluid at temperature T, a natural convection boundary layer flow will form. For laminar flow, the momentum equation is au ди. p(u-+ v) = PB(T – T)g + µ- ди ay to be solved, along with continuity and energy, for (u, v, T) with appropriate boundary conditions. The quantity B is the thermal expansion coefficient of the fluid. Use p, g, L, and (Tw- To) to nondimensionalize this equation. Note that there is no “stream" velocity in this type of flow.
Consider liquid in a cylindrical tank. Both the tank and the liquid rotate as a rigid body. The free surface of the liquid is exposed to room air. Surface tension effects are negligible. Present the boundary conditions required to solve this problem. Specifically, what are the velocity boundary conditions in terms of cylindrical coordinates (r, 0, z) and velocity components (ur, uo, U:) at all surfaces, including the tank walls and the free surface? What pressure boundary conditions are appropriate for this flow field? Explain. Free surface Ps Paa Liquid
Consider dimensionless velocity distribution in Couette flow (which is also called generalized Couette flow) with an applied pressure gradient which is obtained in the following form as attached, where u, V, ∂P/∂x, and h represent fluid velocity, upper plate velocity, pressure gradient, and distance between parallel plates, respectively. Also, u* , y* , and P* represent dimensionless velocity, dimensionless distance between the plates, and dimensionless pressure gradient, respectively. (a) Explain why the velocity distribution is a superposition of Couette flow with a linear velocity distribution and Poiseuille flow with a parabolic velocity distribution. (b) Show that if P*>2, backflow begins at the lower wall and it never occurs at the upper wall. Plot u* versus y* for this situation. (c) Find the position and magnitude of maximum dimensionless velocity.
What are the physical and quantitative evidence of turbulence in fluid flow?
2.0 m 7: 10.0 m = 2²-²² Us B 10.0 m Figure Q1-2 Question 2 Air flow at a constant speed (Us = 10 m/s) is forming a two-dimensional incompressible laminar boundary layer along a flat plate The velocity profile inside the boundary layer is given by: 2.0 m (Equation 1) At x = 1.00 m, the boundary layer thickness is given as 6.6094 mm. At this location: a) Determine the shear stress at the wall, at y = 3 mm and y = 10 mm. b) Calculate the boundary layer displacement thickness. c) Calculate the mass flow rate through the boundary layer per unit width. d) Calculate the mass flow rate per unit width of an ideal flow going through the same height as the boundary layer thickness. e) Through calculation relate the difference between the mass flow rates in parts (c) and (d) to the local boundary layer displacement thickness. In not more than 60 word justify your answer. Use sketch(s) to illustrate your justification. f) Does the assumed velocity profile satisfy the pressure boundary condition? In…
Air flow at a constant speed (Us = 10 m/s) is forming a two-dimensional incompressible laminar boundary layer along a flat plate The velocity profile inside the boundary layer is given by: =2-² A wind tunnel designer plans to build a two dimensional test section for a low speed wind tunnel. The design specification requires that in the test section the free stream flow must be equal to the air velocity at the entrance of the test section. (Figure Q2). U 30 m/s h₁ = 2²-² x,-0.0 Top wall Bottom wall -300 mm X-300 mm Figure Q2 Assuming the same velocity profile as in equation 1, and by using the momentum integral equation determine how much the bottom and top walls should be displaced at point 2 (x₂ = 300 mm) in order to achieve the design requirement as was stated above. In not more than 30-40 words justify your solution. Equation 1:
Consider an airflow over the surface of a flat plate with a temperature Ts = 250 °C. At some distance from y the origin, the temperature profile of the airflow is given by the following function: q/A As, Ts T(y) = T, -(T. -T3)exp -u. y a fluido dAs The airflow at atmospheric pressure has a free flow velocity u.. = 0.06 m/s and a temperature T = 15°C. The thermal diffusivity of the fluid is aluid = 3.872E-05 m?/s and its thermal conductivity Afluid = 0.03383 W/(m K). 1. Determine the heat flux over the surface of the plate. q/A = W/m? 2. Determine the convection coefficient of the airflow. h = W/(m² K)
A fluid Prandti number Pr=1 at 500K flows over a plate of 2.5 m length, maintained at 300K. The velocity of the fluid is 20m/s. Assuming kinematic viscosity v= 20*10^-6 m2/s. Determine the thermal boundary layer thickness at 0.6 m from the leading edge ?
Explain why the incompressible flow approximation and the constant temperature approximation usually go hand in hand.
Explain the fundamental differences between a flow domain and a control volume.