Load Shape Load Outside Diameter Length of Load to Heat Solid or Hollow Wall thickness Heating Goal Material Data Material Emissivity Coil Geometry Process Parameters Start Temperature End Temperature Ambient Temperature Target Heating Time O Cylindrical 1.4 in 5.7 in O Solid 0.16 in Heating the full load Copper 0.78 Multi Turn ID F F F S 75.2 176 68 20 O Rectangular O Hollow

Load Shape Load Outside Diameter Length of Load to Heat Solid or Hollow Wall thickness Heating Goal Material Data Material Emissivity Coil Geometry Process Parameters Start Temperature End Temperature Ambient Temperature Target Heating Time O Cylindrical 1.4 in 5.7 in O Solid 0.16 in Heating the full load Copper 0.78 Multi Turn ID F F F S 75.2 176 68 20 O Rectangular O Hollow

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33MCQ: The direct electrical connection of the windings allows transient over voltages to pass through the...

See similar textbooks

Similar questions

Q-3 A Cockeroft-Walton type voltage multiplier has ten stages with capacitances, all equal to 0.1 µF. The supply transformer secondary voltage is 100 kV at a frequency of 60 Hz. If the load current to be supplied is 5 mA, find (a) the percentage ripple, (b) the regulation, and (c) the optimum number of stages for minimum regulation or voltage drop.
The direct electrical connection of the windings allows transient over voltages to pass through the auto transfonner more easily, and that is an important disadvantage of the autotransformer. (a) True (b) False
help me in these questions pls write the questions with the and by (Computer) 1-Which of the following statements INCORRECTLY explain the label in the figure about LVDT working principles? a. Secondary coils are connected in series in such a way that their output is opposing each other. b. Constant DC voltage input to primary coil. c. Displacement moves ferrous rod from central position. d. The difference of the output voltage between the two secondary voltage.==========2- Explain the working principle of the measurement system in the figure below.i. Force input that is supplied to the sensor is processed to give the response in the form of raw output signal.ii. Signal conditioner manipulated the weak signal to give a conditioned input.iii. Analog or digital indicator display the unit that gives output reading of quantity being measured.iv. Measured value is compared with the input value for further action. a. ii, iii and iv only. b. i, ii and iv only. c. i, ii and…
A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?
Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…
The single - phase ac voltage controller with inductive load. Plot the waveform of output voltage and voltage in each thyristor if the B = 10 %3D degree and delay angle (alpha) in both thyristor is 1- (30 degrees) 2- (90 degrees) 3- (120 degrees)
(5) Primary AC Source Transformer Secondary AC/DC Full-wave Rectifier Capaictor in Non- linear Load Figure 6 Analyse different methods of harmonics mitigation to eliminate the harmonic, which you have identify in above power system circuit. You can use harmonic filters, K or equivalent transformers or oversized neutral method depending upon the harmonic sources.
Voltage sags due to short circuit and earth faults are the cause for the vast majority of equipment problems. Electronics equipment become more susceptible to voltage sag, hence the companies experience production stoppages. Voltage sag analysis is very complex issue. Based on voltage sag randon factors describe on it.
What are the benefits of using mechanical Processes of integrated circuts.
Given the center-tap fullwave rectifier circuit shown 220V 60Hz (+2) 220V:Es1-0-Es2 Es1 E$2 D1 D2 RL The transformer is rated 220V:12V-0-12V (Es1=Es2=12V) and the average current through the load RL is 400mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Power dissipated by the load RL. (c) Average current and PIV of each diode.
Some power devices have bidirectional current capability Select one: O a. True b. False The voltage regulation of the transformer will depend on the load Select one: O a. For mainly inductive or resistive load, the voltage regulation is negative O b. For mainly capacitive, inductive or resistive load, the regulation is positive Oc. For mainly capacitive load, voltage regulation is positive and other loads it is negative. O d. For mainly capacitive load, voltage regulation is negative.
A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of158 volts, 50 Hz supplies the combination. Determine the following:a. Circulating currentb. Voltage across the resistorc. Voltage across the capacitord. Real power supplied by the source