In a main water pipe project the staff readings were as below: 0.95 – 2.05 – 1.50- 2.10 - 2.65 - 1.35- 2.10- 0.55- 1.40-1.10 If the grade of the last point was (402.5m) and the height of the fill in this point was (1.25m), the slope of the road between points (1 to 3) was (-1.2%),(3 to 6) was (0.0%) and (6 to 8) was (6.7%), calculate the depth of cut and the height of fill in each point and draw the longitudinal section of the ground ,if the distance between each point and another was (20m).

In a main water pipe project the staff readings were as below: 0.95 – 2.05 – 1.50- 2.10 - 2.65 - 1.35- 2.10- 0.55- 1.40-1.10 If the grade of the last point was (402.5m) and the height of the fill in this point was (1.25m), the slope of the road between points (1 to 3) was (-1.2%),(3 to 6) was (0.0%) and (6 to 8) was (6.7%), calculate the depth of cut and the height of fill in each point and draw the longitudinal section of the ground ,if the distance between each point and another was (20m).

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter14: Highway Surveys And Location

Section: Chapter Questions

Problem 15P

See similar textbooks

Similar questions

Q2. The reduce level is mentioned in table below to build a wide road with width (8 m) and grade line for the road is (18m) with Sloped down 0.5% and lateral inclination is 1:1. The distance between the station is (100 m). Calculate the total fill and cut volume. 15.4 m 17.5 m 16.5 m 17.2 m Ground Line (G.L) Station 0+00 1+00 2+00 3+00
The table below contains the information about two embankment sections. The distance between them being 30m. The formation width increases uniformly from 6m at the first section to 9m at the second. Calculate the volume between .these sections by trapezoidal formula L -2.07 7.14 -2.16 8.82 CL -2.34 0 -3.45 0 R -3.15 9.30 -3.81 12.12 1149.80.m3 O 1194.282 m3 O 1194.820 m3 O 1149.282 m3 O
box the final answer asap On a railroad a -0.8% grade meters at 0.4% grade station 2+700 whose elevation of 300 m. The maximum allowable change in grade per station having a length of 20m. is 0.12. a. Compute the length of cuve. b. Compute the stationing where a culvert be located. c. At what elevation must tge invert of the culvert be set if the pipe has a diameter of 0.9m. and the backfill is 0.3m depth. Neglect thickness of pipe.
The table below contains the information about two embankment sections. The distance between them being 30m. The formation width increases uniformly from óm at the first section to 9m at the second. Calculate the volume between these sections by trapezoidal formula. L CL R -2.07 -2.34 -3.15 7.14 9.30 -2.16 -3.45 -3.81 8.82 12.12
What is the difference between hydraulic grade (line) and energy grade (line)?
Water is flowing in Four side-by-side pipes. The discharge through each pipe is 1.2 m³/sec and the water depth in each pipe is 0.609D. The Manning's n and the bed slope of each pipe are 0.016 and (1:1000), respectively. After the development, the total discharge is expected to increase by 13%, and the engineers have decided to replace the Four pipes by a trapezoidal channel. The new channel with a non- cohesive material having a particle size of 0.61 mm with the same bed slope of the pipes. Assume the channel bed width is twice the water depth, and the side angle of the channel is 60°. 1- Determine the diameter of the pipes. 2- Design the cross section of the new channel and what are your comments and suggestions about the hydraulic flow in the designed channel? 3- If a hump is placed in the bottom of the designed channel, Estimate the hump height which will cause the crest flow to be critical.
Pipe design A stretch of corrugated metal pipe (n = 0.024) is needed to convey a design storm flow rate of 32 cfs.Site conditions dictate a pipe slope of 0.002. If pipe sizes (diameters) are available in increments of 6in., determine the minimum size pipe that will both convey the design flow rate and achieve aminimum scouring velocity of 3 ft/s. Assume the pipe is flowing full. Tip: Determine the pipediameter needed for a flow rate of 32 cfs, then do the same for a velocity of 3 ft/s, and round up to thenearest multiple of 6 inches
• Example:- A Sewer is to be laid at a uniform gradient of 1 in 200, between two points X and Y, 240 m apart. The reduced level of the invert at the outfall X is 150.82m . In order to fix sight rails at X and Y, readings are taken with a level in the following order: Reading |Staff station Near X R.I 153.81 B.S. 0.81 I.S 'a' I.S 1.07 F.S 0.55 Top of sight rail at X Peg at X C.P. between X and Y B.S 2.15 C.P between X and Y I.S b' Top of sight rail at Y F.S. 2 Peg at Y • i) Draw up a level book and find the reduced levels of the pegs. ii)if a boning rod of length 3m is to be used, find the level readings a and b. • liFind the height of the sight rails above the pegs at X and Y.
a.) If the percent grade is 7.25 % and the horizontal length of grade is 1625 feet, what is the change in elevation? b.) Given a manhole with the outlet invert elevation of 2605. A run of 48 inch pipe connects to the next manhole at an invert elevation of 2610. What is the distance between manholes if the correct pipe grade is 3%?
Design rectangular channel in formed unfinished concrete. 0-5.75 m3/s 0.017 S-1.2% Normal depth-% of the widtrof the channel Since we have to design the channel-the equation that should be used AV AR RHS is known Now wekao thaiy 62 Express Area and the hvdrautic radius in terms ofE
0.2A concrete pipe culvert is to be constructed under road to carry a max. Discharge Sm /sec. if the length of pipe culvert 10m @ slope 1/100 , find the diameter of the pipe & draw the culvert between the change of discharge & the diameter.
• Example:- A Sewer is to be laid at a uniform gradient of 1 in 200, between two points X and Y, 240 m apart. The reduced level of the invert at the outfall X is 150.82m . In order to fix sight rails at X and Y, readings are taken with a level in the following order: Reading B.S. 0.81 I.S'a' I.S 1.07 Staff station Near X R.I 153.81 Top of sight rail at X Peg at X F.S 0.55 C.P. between X and Y B.S 2.15 C.P between X and Y I.S 'b' Top of sight rail at Y F.S. 2 Peg at Y • i) Draw up a level book and find the reduced levels of the pegs. • ii)lf a boning rod of length 3m is to be used, find the level readings a and b. lii)Find the height of the sight rails above the pegs at X and Y.