From the figure below, assume 8 K1 = K2 = 4 K3 = 2 K4 and that layer 2 and 3 are of equal heights. AB = 12 cm, BC = 18 cm and CD = 15 cm. All remaining units are also in cm. K2 K4 K3 a. Determine the pressure head at point B in m. (IN 2 DECIMAL PLACES) b. Determine the pressure head at point C in m. (IN 2 DECIMAL PLACES) c. Determine the rate of flow in cm^3/s if K1 = 4.60 x 10 cm/s (IN 2 DECIMAL PLACES) 28 Z1

From the figure below, assume 8 K1 = K2 = 4 K3 = 2 K4 and that layer 2 and 3 are of equal heights. AB = 12 cm, BC = 18 cm and CD = 15 cm. All remaining units are also in cm. K2 K4 K3 a. Determine the pressure head at point B in m. (IN 2 DECIMAL PLACES) b. Determine the pressure head at point C in m. (IN 2 DECIMAL PLACES) c. Determine the rate of flow in cm^3/s if K1 = 4.60 x 10 cm/s (IN 2 DECIMAL PLACES) 28 Z1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid bar ABC shown is hinged at A and supported by a steel rod at B. Determine load P that can be applied at C if the stress in the steel rod is limited to 120MPA. E=200 x 10° N/m2 A-300mm? L-3m 3 m 4.5 m
•213. The rigid bar AB, attached to two vertical rods as shown in the figure, is horizontal before the load is applied. If the load P=50KN, determine is vertical movement. ALUMINUM L=4m A=500mm? STEEL L=3m A=300mm2 E=200GPA E=70GPa 2m 3m
A structural steel rod 1(1)/(2) inches in diameter and 25 feet long, in supporting a balcony, carries a tensile load of 29k;E=29 xx10^(3)ksi. a. Find the total elongation delta of the rod. b. What diameter d is necessary if the total delta is limited to 0.1 inch?
The cross section of a slit rectangular tube ofconstant thickness is shown in the figures.(a) Derive the following formula for the distance efrom the centerline of the wall of the tube in thefigure part a to the shear center S: e = [b(2h+3b)/[2(h+3b)] (b) Find an expression for e if flanges with the samethickness as that of the tube are added as shownin figure part b.
The beam is subjected to a bending moment of M = 17 kN. m. σA = B 200 mm OB = 30 mm 30 mm M 30 mm 30 mm 50 mm 150 mm 150 mm 50 mm Part A Determine the bending stress in the beam at point A. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in the case of tension. ANSWER: Q Tap image to zoom Part B Determine the bending stress in the beam at point B. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in the case of tension. ANSWER:
QUESTION 4 The assembly consists of three titanium (E is 120 GPa) rods and a rigid bar AC. The cross sectional area of each rod is given in the figure. If force of 30 kN is applied to the ring F, determine the horizontal displacement of point F. 1.2 m AcD = 600 mm² %3D 0.6 m 03m E 30 kN 0.3 m AEF = 1200 mm? A AB= = 900 mm2 1.8 m
Given is a thin-walled tube with the following data: Determine the following: a. Enclosed Area Wall thickness- 2mm b. Perimeter of the thin walled tube ABC is a sector with a radius of 50 mm c. Shear flow AOD & COD is a triangle Torque is 1000 N.m Length of the thin walled tube is 0.5 m Use G=24 GPa for aluminium d. Shear stress e. Angle of twist A R 90° в D 3R
A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the %3D figure. Determine the total resultant force acting on the gate and the location of the center of pressure. 6 ft 3ft VAVAVAVAVA Ib f Unit weight of the liquid (y) Value of hbar (h) Arca of the rectangular gate (A) Hydrostatic Force (F) Vahe of (Igx) Vahue of ybar (9) Location of the Hydro. Force measured from the water surface of the gate inclined (yel Ib ft ***answer Hydrostatic Force Fon the box below: Answer: 1311.03 The correct answer is: 1022.1
• The three steel bars shown in the figure are pin connected to a rigid member. If the applied load on the member is 15 kN, determine the force developed in each bar. Bars AB and EF each have a cross- sectional area of 50 mm2, and bar CD has a cross-sectional area of 30 mm?. Take Est = 200 GPa. B D F 0.5 m E - 0.4 m- 0.2 m 0.2 m 15 kN
From the figure below, assume 2 K1 =1.2 K2 = 2.7 K3 = 3 K4 and that layer 2 and 3 are of equal heights. AB = 8 cm, BC = 12 cm and CD = 10 cm. All remaining units are also in cm. A K2 K1 K4 K3 a. Determine the pressure head at point B in m. (IN 2 DECIMAL PLACES) b. Determine the pressure head at point C in m. (IN 2 DECIMAL PLACES) c. Determine the rate of flow in cm^3/s if K1 = 3.5 x 10^2 cm/s (IN 2 DECIMAL PLACES) 28
. Consider the following wooden T-beam on its side. It consists of two wooden parts glued together. Assume the glue nas a perfect bond. The densities of the two wooden parts differ and are indicated on the figure. The figure is not to scale. y Pq = 900 kg/m %3D 17 mm P2 = 740 kg/m? 20 mm 150 тm Determine the a-coordinate I of the center of mass of the T-beam. 90 mm
To lower ends of the three bars in the figure two are the same level before the rigid homogeneous W=176kN block is attached. Each still bar has a length of 1.00 m, an area 500mm² and E=200 GPa. For the bronze bar the length is 1.6m, the area is 900mm² and E= 83 GPa. What is the stress developed in the bronze bar? What is the stress developed into steel bar? What is the elongation of each bar?