For the circuit of Figure 2. Assuming that the capacitor voltage and inductor current are equal to zero at t = 0. a) Determine the expression for all the branch currents and capacitor voltage v(t) b) Obtain the plots of the branch currents and v(t) by creating a MATLAB model in Simulink. Verify the plots by using a MATLAB program

For the circuit of Figure 2. Assuming that the capacitor voltage and inductor current are equal to zero at t = 0. a) Determine the expression for all the branch currents and capacitor voltage v(t) b) Obtain the plots of the branch currents and v(t) by creating a MATLAB model in Simulink. Verify the plots by using a MATLAB program

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 1RQ: 1. What is the dielectric?

See similar textbooks

Similar questions

Circuits 1 HW 7 Q4
If the measured values of R1 = 323.1 Q, R2 = 324.2 Q and R3 = 324.7 Q, calculate the difference in measured R compared to your calculation of equivalent R in Ohms? KIT NO. 1PASCO EM-8622 SCIentfic CYRCUIT EXPERIMENT TENMA 72-7780 1079 A C Auto Range 6000 Counte True RMS Multimeter ANGE MAX/MIN RELA Hz/% DILIGHT SELECTIVR.C Hz% mA H Am Hz% ONCV 60A. CE A (10mviA) VOHZC ww COM FUSED FUB RI
Calculate the voltage at 1.5¹ (milliseconds) for the following RC Circuit. Assume switch is closed and capacitor is in a charge state. t=0 LE -10 V oto R1 1kQ C1 1uF
Q1 Explain the following terms: (a) Sensor (1.5 marks) (b) Transducer (1.5 marks) (c) Instrument Q2 Q3 (2 marks) Based on Figure Q2, if the RTD sensor measurement is 57°C answer the following. (a) Calculate the output current from RTD sensor if the output range is 4 20mA. (2 marks) (b) Calculate the output voltage from the temperature controller if the output range is 0-10VDC. (2 marks) (c) Propose a type of sensor if the process temperature is increased to 1000°C. (1 marks) A capacitive displacement transducer is designed to determine the rotary position. from 0° 180° as shown in Figure Q3. The moving plate whose radius is 40mm is sandwiched between two fixed plates, spacing at Imm. The dielectric constant of air is k 1.The capacitive transducer is formulated as: where; (a) kA€。 farads k = dielectric constant A the area of the plate, in square meters €₁ = 8.854 × 10-12 in farads per meter d = the plate spacing in meters Construct an equation of the change of the capacitance (F) when…
5. Suppose the following circuit is left open for a long time. 5000 22 24 V (a) What is the facial curren What is the carte II What is the ches What is the not the pos 80mF when we close thei 90s after we close the switch? dissipe the resistor 90s arter ene capacitor ons after we close the suit Close the switchi difference across the spacitor 008 after we close the switch across the resisto we close the swit 12 the potential (g) What is the energy stored in the capacitor 90s after we close the switch? (h) What is the energy dissipated by the resistor during the first 90s since the switch is closed?
Find the charge across the capacitor C3 CT C3 E 50μ | 80μF 100μ F 150V O 15000 µC O 15000C 15 μC O NONE
The discharging time constant for the circuit below is _nanoseconds. 5 V MPU 2 kQ RESET 100 kQ 1 pF SW 1
Consider the circuit shown below. b) a) What is the current through 220 22 when the 2N4441 is conducting? What is the capacitor voltage that will turn on the 2N4441? What is the minimum voltage that can turn-off the 2N4441? c) 0.2 μF 2.2 1 kQ 1N752 VB = 10 V 9+25 V 220 2N4441 V₁ = 1 V IT = 7 mA IH= 5 mA
C) A 25 A electrodynamic ammeter is controlled by a spring having a constant of 5.7295x 10-6 Nm/rad. The full scale deflection is 110°. Determine the inductance of the instrument while measuring a current of 20 A. The mutual inductance at 0° deflection is 4 u H and the change in mutual inductance is linear with the deflection.
Consider the diagram of the following figure: Determine the charge voltage and energy of each of the capacitors. Make and complete your data table, if the voltage is 300 V C UF C₁= 30 C₂=60 C₁=22 C=74 Cs=32 Co=45 q μC V V W E 300 60μF 22HF C2 C3 30MF C1 CA 74 MF C5 32AF :C6 45MF
Find the charge across the capacitor C3 CT C1 C2 C; E- 25μF 90μF 60μ 200V Ο 12 μC O 12mC O 1200mC O NONE
Band 1 GR R y BU G GR BN G Band 2 R W V V GR BU R GR W BU Band 3 BN R BL S R R BL GO BL R Table 1 Resistor Color Codes and Measurements Band 4 GO 60 GO GO GO GO GO GO GO GO Band 5 Theoretical value R Plus Tolerance 8205% 8612 3 900±5% 40952 3705 27 2±5% 28-35 25-65 0.47±5% 0-493552 0.44651 71402 6800 ± 5% 5600 55880 82nt 5% 1-82±5% 86-1-22 1.892 R Minus Tolerance 39 150 40.952 56001 ± 540 5880 Measured Value 7792 8012 38542 26 0.45 6460 6630 53201 5570 77-92 80.5 #1.712 37.05~ 5320 2 1.82 39.25 5520 MAKE A CONCLUSION FOR THIS (8 SENTENCES ONLY) The content must be the connection of resistor color codes to tolerances and the relationship of the measured value to the theoretrical value