Answered: For a transmission line, magnitude of…

For a transmission line, magnitude of OC impedance is 120 and SC impedance is 50, then which of the following will be the value of characteristic impedance?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.14MCQ: The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load...

See similar textbooks

Related questions

Q: What is the output of e-4t u(t) * e¯³t u(t)? e-3t 1 e -4tu(t) - e-³tu(t) 2 e-3tu(t) -e-4tu(t) 3…

A: Given- Signal expression, e-4tut*e-3tut To find- The output of the expression.

Q: For the feedback control system given in the figure on the right, R(s) + (a) Find the closed-loop…

A: To plot the step response for the input of 1.5u(t) when K = 22, we need to find the closed-loop…

Q: Obtain the node voltages in the circuit in Fig. 3.4. Answer: V₁ = -2 V, 0₂ = -14 V.

A: It is given that:

Q: The transfer function of a system is The corner frequencies will be 10(1+0.2s) (1+0.5s)

A: Transfer function of a system:G(s)=10(1+0.2s)(1+0.5s)

Q: Explain the advantages and disadvantages in using a brushless or brush motor. For the hydraulic…

Q: jo.53 1 j0.4 j0.3 3 20.07 j0.2 ammfo

Q: Find the power delivered to an element at t = 3 ms, if the current entering its positive terminal…

A: We need to find out the power delivered for given current and voltage at given time instant .

Q: In the circuit of the following figure, the input voltage Vs is 15 volts rms with a frequency of 60…

A: Input voltage Vs=15 V (rms) Frequency f=60 Hz Resistance R=150 ohms Capacitance C=100,000 pF Vd=0.2…

Q: (5) For the feedback amplifier of Fig.5, derive an expression for the voltage gain (V./Vin).

Q: Problem 1. A signal x(t) with frequency as given below is passed through an ADC (Analog to Digital…

A: Analog to Digital Converter: When a continuous time domain signal is passed through the ADC it…

Q: Determine the steady-state and transient responses of the system y(n) = 0.5[x(n) − x(n − 2)] to the…

Q: Find Vo for the circuit in Figure using Mesh Analysis

A: The value of voltage across the resistor needs to be calculated by using the mesh analysis.

Q: A 240 V, Short – Shunt DC Generator supplies a load current of 60 A. The armature circuit resistance…

Q: UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. SOLVE IN 4 DECIMAL PLACES. BOX…

A: Given: A network, with f = 50 Hz. To find: Using nodal analysis, we have to find VAB.

Q: 3. The circuit below has an AC power supply with 20 V max voltage and a frequency of 50 Hz.…

Q: 3. Find the spectral peak frequency (f) shown on the spectrum analyzer trace below: Spectrum…

Q: what's the value of the output signal if the system is connected to an outlet in a house in berlin,…

Q: 2-(XXXXX) (YY) (YY)

Q: (a) (b) Vo R₁ www R₂ Figure Q4 Derive the gain of the circuit shown in Figure Q4 showing all steps…

A: The above question is based on the opamp circuit. We use the virtual short concept along with nodal…

Q: Find the voltage drop VR(t) across the resistor when w=8wo. Suppose that UR (t) = AR cos(wt+), where…

A: For the given band reject filter circuit the value of the voltage at various values of the angular…

Q: The peak-to-peak voltage is 40V, its rms voltage is 14.1 V 11.4V 13.3V 12.3 V

A: Peak to peak voltage Vp−p=40 V.

Q: Evaluate the following expressions. Provide your answer in polar form. i) (4+j2)(2e-/18⁰) (6-j)² ii)…

A: The above question is based on phasor calculations in complex form. We use the rectangular form for…

Q: What have you observed in the behavior of the elements? Did the lamps light up? Explain.

A: For the given series connection of Bulb, the behavior of the elements needs to be analyzed.

Q: (i) Given R₁ =10k, R₂-30k and Vs = 12 volts for Figure Q1 (a), what value would a voltage…

A: The above question is based on the measurement of voltages in a resistive circuit. The voltage…

Q: Between the concentric spheres with radius r = 1m and r=6m, there is material with an electrical…

A: Use the Laplace equation in spherical coordinates 1/r^2 ∂/∂r(r^2 ∂V/∂r) = -ρv/ε Integrate the…

Q: A linear system is described by the differential equation. Find the system poles and zeros. Plot…

A: here we have to find the system poles and zeros.

Q: Let a = (7,7,9) and b = (8, 7, 9) be vectors. (A) Find the scalar projection of b onto a. Scalar…

Q: Determine the impulse response and the step response of this stable causal system using Z-transform.…

Q: Vi 3 v + 1 Fig. 1 Vi R₁ TTİNT Fig. 2 R

Q: Rank the systems in terms of how quickly they reach their steady-state values.

A: According to the question, for the given graph as shown below We need to rank the systems in terms…

Q: The cost of a single phase overhead transmission line is Rs (25000 a + 1500) per km where 'a' is the…

A: We have an 3-phase overhead line which has, Cost of transmission line = 25000 a + 2500 Rs/km a =…

Q: State four (4) advantages of the suspension type insulators.

Q: cuicuit designed in winknown subuenit, va resistance R = 2.8K2 and two identical silicon BTTS T₁ and…

Q: Vin страни 300 5 ww 400-52 IMF CON No зорін

A: I'm going to apply sinusoidal analysis for both A.C input and D.C input separately accordingly we…

Q: A conductor of length 15 cm is moved at 750 mm/s at right angles to a uniform flux density of 1,2 T.…

A: To determine the emf induced in the conductor, we can use Faraday's law of electromagnetic…

Q: What is the value of mesh current i₂? 4 Ω ΣΩ 10 Ω www ΤΩ 8V 6V Μ 5Ω

A: We need to determine the mesh current i2.

Q: A buck converter is to allow an input voltage between 22 V and 40 V, and provides tightly regulated…

A: Buck converter Input voltage, Vs=22 V to 40 V Output voltage, V0=12 V Capacitor ripple =+- 1%…

Q: Determine Rin Express your answer to three significant figures and include the appropriate units.…

A: For the given inverting amplifier circuit the value of input resistance for the given gain needs to…

Q: In the electrical circuit shown, the components have the following values: V = 120 volts R₁ R₂ = 69…

A: For the given circuit the total current in the circuit needs to be calculated. The total resistance…

Q: 8. Answer the following questions about this circuit. C-0.039µF, Vin-IV, R-3.9 k2 R www 39 ΚΩ Q039…

A: Given Data: An RC circuit with, Input voltage Vin=1 V Output voltage =Vout To Find: Phase shift…

Q: For class AB amplifier the R.M.S. input voltage is IIV and the supply voltage is +20V and the laod…

A: Find (a)The current through the diode (b)The power dissipated in the load (c)The dissipated power at…

Q: L1 L2 Voltage (V) 120 L3 E1 E2 + Local ac power network Frequency (Hz) 60 R₁ (22) + 300 11 12 R2, R3…

A: In this question We need to find the total active power, reactive power and apparent power.

Q: An open-loop control system results in a response of e 2 (sin 5t + cos 5t) for a unit impulse inpu…

A: Response of an open loop control system is, ct=e-2tsin5t+cos5t Input is unit impulse, rt=δt.

Q: the power to be supplied to a machinery that will be used for pump if it draws 255 A of current from…

A: In electrical systems, power is the rate at which energy is transferred from one system to another.…

Q: Question 18 Select the correct intersection of the asymptotes and the real axis: O-4/3 0 0 O-2…

A: In this questions we need to choose a correct option

Q: Consider two discrete-time LTI systems with impulse responses hi[n] h₂[n] = = (n + 4)u[n+3]u[-n − 1]…

Q: For the circuit shown below, find the value of AVO, if duty ratio of switch is 0.4 and it is…

A: Buck-Boost convertor Duty ratio, α = 0.4 Frequency, f = 25kHz

Q: Problem 1: In the circuit shown in figure, the switch S has been closed for a long time. It is…

A: As the circuit is opened for a long time, the capacitor voltage before time t<0 is equal to zero.…

Q: Problem 1. A signal x(t) with frequency as given an ADC (Analog to Digital Converter) running at…

A: Analog to Digital Converter: When a continuous time domain signal is passed through the ADC it…

Q: Consider the unit-step response of a unity-feedback control system whose open-loop transfer function…

Question

For a transmission line, magnitude of OC impedance is 120 and SC
impedance is 50 , then which of the following will be the value of
characteristic impedance?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given Data:-

VIEW

Step 2: Calculation of characteristic impedance.

VIEW

Solution

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Transmission Line Parameter and Scattering Parameter (S-parameter)

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

estimate the value of equivalent impedance
Determine the value of impedance Z.
Subject - Design electrical circuits for single phase AC networks Question - Discuss the difference between resonant and non-resoinant circuits. Use equations to explain your answer.
2-A resultant current is made of two components: a 10 A D.C. component and a sinusoidal component of maximum value 14.14. The average value of the resultant current is amperes (a) 0 (b) 24.14 (c) 10 (d) 4.14 and r.m.s. value is - amperes (e) 10 (f) 14.14 (g) 24.14 (h) 100
3. A sinusoidal voltage is applied to the circuit below. Determine the following: I, Irms, lavg, Ip- 1.0 kN
7. Show the result of sin (wt - 30º) + cos(wt + 10°) in cosine format. With the use of phasor. a) b) Without the use of phasor.
Impedances Z1 = 5.83 at angle of -59 deg. and Z2 = 8.94 at an angle of 63.43 deg. are in series and carry an effective current of 5A. Determine the Power and power factor of the circuit indicating if it is leading or lagging.
The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
For the pair of waveforms (input and output) captured in that picture, write the mathematicalexpression for Vout(t), using the phase of Vin(t) as the reference. Also, write the phasor expressions forVout and Vin. Vin = Yellow line Vout = Blue line Vin max = 2V Vout max = 440.0 mV phase = -78.7483
Give example problems for impedances and admittance.
A transmission line section shows an input impedance of 36 and 64 respectively, when short circuited and open circuited. What is the characteristics impedance of the transmission line?
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance