• Write your answer to the blank field in this format: xXXX.Xx (e.g., 2004.32)• Use dot (.) as the decimal separator• Use only two decimal places after the decimal separator.• Use grad unit for angles.• Do not add "m" or "meter" at the end of your answer.Find the sum of the coordinates (Y+X) of point "D" on a line linking N11 and N29, whose coordinates are given. Use intermediate point calculation method.X(m)PNY(m)2525.582004.32N112598.44N29 2075.34N 101.79oi 72.58C46.96Bộ32.74P17.340.00N11

A coordinate system is a way of calculating points in a system area with the correct calculation.…

Find the sum of the coordinates (Y+X) of point "D" on a line linking N11 and N29, whose coordinates are given. Use intermediate point calculation method. •Write your answer to the blank field in this format: xxXX.Xx (e.g., 2004.32) •Use dot (.) as the decimal separator • Use only two decimal places after the decimal separator. - Use grad unit for angles. - Do not add "m" or "meter" at the end of your answer. PN Y(m) X(m) N11 2004.32 2525.58 N29 2075.34 2598.44

Find the sum of the coordinates (Y+X) of point "D" on a line linking N11 and N29, whose coordinates are given. Use intermediate point calculation method. •Write your answer to the blank field in this format: xxXX.Xx (e.g., 2004.32) •Use dot (.) as the decimal separator • Use only two decimal places after the decimal separator. - Use grad unit for angles. - Do not add "m" or "meter" at the end of your answer. PN Y(m) X(m) N11 2004.32 2525.58 N29 2075.34 2598.44

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Rectangular paper WXYZ Length = 20 cm Width = 26 cm If W and Y will touch each other. Y Line ab will appear. a Find length of ab.
X=30 Y=25
X= 6 Y= 8
Determine the coordinates of the centroid of the lines shown with respect to the indicated X and Y axes. A. B. 2 60 mm ¥ … 80mm 5洲 80mm + 为那时 x
X= 256 B= 5
X = 856 Y = 56 A = 8 B = 2 C = 5
Subject: Engineering Drawing or AutoCAD Instruction: Do and draw the following tasks. You can freehand draw or use AutoCAD. a. Draw a circle touching three points A, B and C with distances given as AB=4 units, BC=6 units, and CA=8 units. b. Draft an angle equal to 75 degrees from the horizontal. c. Draw a regular hexagon having length of side as 45mm. d. Draw a nine-sided regular polygon inscribing a circle of radius 50mm. e. Draw an ellipse having major and minor axis length as 85mm and 50mm. f. Draw an ogee curve to connect two parallel lines each of length 25mm and their mid-points spaced 35mm vertically and 65mm horizontally.
Question 6 Determine the coordinates of the centroid of the shaded area. (X,Y)= (Blank 1,Blank 2) mm Blank 1 Add your answer Blank 2 Add your answer 10 30 y 15 10 55 15 25 15. Dimensions in millimeters --x
112 mm К30 тm -> 30 тm -+30 тm ->-30 mт -> Part a) Determine the moment of inertia of the shaded region around the – axis. mm4
+84 60 Determine the centroidal x-coordinate (in mm, round-off to 2 decimal places) of the plane region shown. 240 210 Dimensions in mm 360 60
Solve Handwriting i requested to u. With Diagram
Read the question carefully and give complete solution. Dont miss anything. X=10