Googlex Section 5-Qui -1- Mr. Prasad KIhttps://moodle.nct.edu.om/mod/quiz/attempt.php?attempt 1e-Learning PortalCourses Reports e-Services Academic Departments ETC CIMS-Find the current flowing through the resistors R1, R2, R3 and R4 using Kirchoffs Voltage law if RI 160R2 150, R3-9O, R4-60 and Va40Volts. Write the equations for loop 1 and 2.R1R2Loop1 R4Loop2) R3 ECurrent flowing through R1Current flowing through R2Current flowing through R3Current flowing through R4Fipish attemot

Given Data: The resistances R1, R2, R3 and R4, are given as, R1=16 ΩR2=15 ΩR3=9 ΩR4=6 Ω The voltage…

Find the current flowing through the resistors R1, R2, R3 and R4 using Kirchoffs Voltage law if R1 162 R2-150, R3-90, R4-60 and V40Volts. Write the equations for loop 1 and 2. R1 R2 Loop1 R4 Loop2) R3

Find the current flowing through the resistors R1, R2, R3 and R4 using Kirchoffs Voltage law if R1 162 R2-150, R3-90, R4-60 and V40Volts. Write the equations for loop 1 and 2. R1 R2 Loop1 R4 Loop2) R3

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter27: Current And Resistance

Section: Chapter Questions

Problem 27.11OQ: Two conducting wires A and B of the same length and radius are connected across the same potential...

See similar textbooks

Related questions

Q: The figure shows the resistor wired in a different way -- a combination of series and parallel.…

Q: 1. for this circuit you need to show your work find the total resistance, total current, the current…

Q: The electric current I in a circuit shown in the figure was measured as a function of the resistance…

A: In the circuit Relationship between the current, emf and resistance. Where r internal resistance R…

Q: the circuit below, two currents are known (as indicated in the circuit) but the emfs of two…

Q: More Circuit Analysis For each circuit in Problems - 80, use Kirchoff's Current Law (Problem 76) to…

A: According to Kirchhoff’s current law (KCL), the algebraic sum of incoming current at a node will…

Q: Initially, a circuit is composed of a DC source and two resistors, R₁ and R₂, connected in series…

Q: For the circuit diagram shown below, determine the currents I1, 12 and 13. Use the loop directions…

A: We have a circuit with 2 voltages V1=18 V and V2=24 volts and currents I1, I2 and I3 running through…

Q: Consider the circuit shown below, with resistors R1, R2, R3, and batteries with emfs E1 and E2.…

A: Krinchoff's loop.law states that in a closed loop, the rise in potential is always equal to.fall in…

Q: Figure shows the resistors from the previous two examples wired in a different way—a combination of…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: Problem 2: The values for the components of the circuit shown in the figure are V= 12 V, C = 4.2 µF,…

Q: All capacitors of the open circuit in Fig. 3 are discharged at time t = 0, when the switch S is…

Q: In the circuit in the figure, switch S has been open for a long time. (a) What is the current in…

Q: What is the current read by the ammeter in the circuit below? Let: R1 = 1 kiloohm. R2 = 2 kiloohm.…

A: Given Data: The resistors are, R1=1 kΩ, R2=2 kΩ, R3=3 kΩ. The emf is, V = 5 V. The current can be…

Q: How does the voltage across R1 compare with that through R2? What is the connection between the…

Q: What is the Thevenin equivalent of the circuit shown below? a) Draw the Thevenin equivalent circuit…

A: The equivalent Thevenin circuit of the above circuit as shown below.

Q: R1 R1 Repeating to infinity R2 R2- R1 R1 9Ω and R, 182 extends to infinity %3D %3D A network of…

A: Given : Network of resistors of resistance R1 = 9 ohm R2 = 10 ohm We have to calculate the…

Q: For the given resistor combination circuit, determine (a) )the equivalent resistance (show…

A: Given data for part c:V1= 18V, V2=12V, V3 = V4 = 6V, V5 = V6= 3V V7=2V V8=0.83V V9=1V…

Q: A circuit is constructed using two batteries and three resistors. R, What is the current I2 through…

Q: Consider the multi loop circuit shown in Figure 9. Directions of the currents and the numerical…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts (a, b,…

Q: In the circuit below, if the battery in the circuit below is 3V, resistor R₁=1540, and resistor…

A: Given data: Battery voltage (V) = 3 V Two resistors are connected in parallel R1 = 154 Ω and R2 =…

Q: The part with the switch and two resistors R1 in parallel of the circuit below dissipates the same…

Q: r resistors A1. 2. and A3 respectively. Iinput E for the emf e. Use context clues to fgure out if…

A: Let R1=1 kilo-ohm, R2=2 kilo-ohm, R3=3 kilo-ohm & the emf of the ideal source is ε=5 Volts.…

Q: What is the current read by the ammeter in the circuit below? Let R1 = 1 kiloohm, R2 = 2 kiloohm, R3…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: The voltage, V, in a simple electrical circuit is slowly decreasing as the battery wears out. The…

A: Ohm's law gives, V=IR Taking the derivative with respect to time on both sides of the above…

Q: V₁ and V₂. L3 R1 Consider the circuit below with two junctions, J1 and J2, three resistors R₁, R2,…

Q: 52 15V 252 -Is->

Q: Find the Thevenin equivalent circuit of the circuit in the figure, to the left of terminals a-b.…

Q: Consider the circuit shown in the figure. A) Let the equivalent resistance of the circuit when the…

Q: QU6 In a series circuit, a capacitor C is being charged through a resistor R using a cell of emf E…

Q: Crystal's class is studying parallel circuits. The teacher asks what will happen if one of the light…

A: In this question we are given with a situation where one bulb is broken in a parallel combination of…

Q: Two resistors and two capacitors are connected in series to a battery as shown below Calculate the…

Q: In the circuit below (See Figure 5), the capacitor C is initially uncharged and switch S is closed…

Q: Figure 2 below shows a capacitor of capacitance C is connected in series with battery of emf, E, a…

A: Given : Asked to answer the second part of a Emf of the battery = E Resistance of the resistor = R…

Q: 91 ndidentify the two 28918 the circuits shown. Each circuit has a switch S in the open position.…

Q: The electric current I in a circuit shown in the figure was measured as a function of the resistance…

A: Given: The relation between current voltage resistance and internal resistance is,

Q: Problem 8: A capacitor of capacitance C-10 uF has been charged so that the potential difference…

A: Given: Capacitance, C = 10 microfaradPotential difference, Vo = 380VResistance, R = 6.5 kilo-ohm

Q: What do you mean by power rating of an electrical appliance? How do you use it to calculate (a) the…

A: An electrical appliance such as electric bulb, geyser etc. is rated with power (P) and voltage (V)…

Q: What is the current read by the ammeter in the circuit below? Let R1 = 1 kiloohm, R2 = 2 kiloohm, R3…

A: general formula for current, I =VRcurrent across the resistor R1I1=VR1=51mA=5 mAcurrent across the…

Q: Circuits 6 and 7 show the three resistors connected in series-parallel combinations. Investigate…

Q: Can you calculate the current through each resistor right after the circuit is connected? If so, can…

A: From Kirchoff's node rule, net incoming current must be equal to net outgoing current at any node of…

Q: What is the curent read by the ammeter in the circuit below? Let R1 = 1 kiloohm, R2 = 2 kiloohm, R3…

A: The resistance of the resistor R1=1 kΩ=1000 Ω The resistance of the resistor R2=2 kΩ=2000 Ω The…

Q: Given the parallel circuit presented below IT A I, R1 R2 R3 12v The total power that the Power…

A: Given: The supplied voltage is 12 V. The power is 120 watts. I3 = 3 A, and R2=4 Ω.

Q: Four circuits have the form shown in the diagram below. The capacitor is initially uncharged and the…

A: given that: E = 12V, R = 1Ω, C = 7μF E = 18V, R = 3Ω, C = 1μF E = 10V, R = 5Ω, C = 7μF E =…

Q: Consider the circuit shown. Assume that the battery connected is ideal. Let V = 16V, C = 2µF, R1 =…

A: Given: Source voltage, V1=16 V C1=2 μF=2×10-6 F R1=1 kΩ =103 ΩR2=R3=R4=13 kΩ =13×103 Ω

Q: Calculate the voltage across resistor R4.

Q: ur circuits have the form shown in the diagram below. The capacitor is initially uncharged and the…

Q: Part A and B Please and thank you In the circuit shown the switch S can be open or closed. Case 1:…

A: Switch is open means that no current flows through that part of the circuit. Let

Question

Google
x Section 5-Qui -1- Mr. Prasad KI
https://moodle.nct.edu.om/mod/quiz/attempt.php?attempt 1
e-Learning Portal
Courses Reports e-Services Academic Departments ETC CIMS-
Find the current flowing through the resistors R1, R2, R3 and R4 using Kirchoffs Voltage law if RI 160
R2 150, R3-9O, R4-60 and Va40Volts. Write the equations for loop 1 and 2.
R1
R2
Loop1 R4
Loop2) R3 E
Current flowing through R1
Current flowing through R2
Current flowing through R3
Current flowing through R4
Fipish attemot

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

(a) Find the current in each resistor of Figure P18.18 by using the rules for resistors in series and parallel. (b) Write three independent equations for the three currents using Kirchhoffs laws: one with the node rule; a second using the loop rule through the battery, the 6.0- resistor, and the 24.0- resistor; and the third using the loop rule through the 12.0- and 24.0- resistors. Solve to check the answers found in part (a). Figure Pl8.18
Currents of approximately 0.06 A can be potentially fatal. Currents in that range can make the heart fibrillate (beat in an uncontrolled manner). The resistance of a dry human body can be approximately 100 k . (a) What voltage can cause 0.06 A through a dry human body? (b) When a human body is wet, the resistance can fall to 100 . What voltage can cause harm to a wet body?
Integrated Concepts A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. (a) What is the battery’s internal resistance? (b) What power is dissipated inside the battery? (c) At what rate (in °C/min ) will its temperature increase if its mass is 20.0 kg and it has a specific heat of 0.300 kcal/kg. °C, assuming no heat escapes?
Residential building codes typically require the use of 12-gauge copper wire (diameter 0.205 cm) for wiring receptacles. Such circuits carry currents as large as 20.0 A. If a wire of smaller diameter (with a higher gauge number) carried that much current, the wire could rise to a high temperature and cause a fire. (a) Calculate the rate at which internal energy is produced in 1.00 m of 12-gauge copper wire carrying 20.0 A. (b) Repeat the calculation for a 12-gauge aluminum wire. (c) Explain whether a 12-gauge aluminum wire would be as safe as a copper wire.
Two conducting wires A and B of the same length and radius are connected across the same potential difference. Conductor A has twice the resistivity of conductor B. What is the ratio of the power delivered to A to the power delivered to B? (a) 2 (b) 2 (c) 1 (d) 12 (e)12
A typical cell phone consumes an average of about 1.00 W of electrical power and operates on 3.80 V. (a) What average current does the phone draw from its battery? (b) Calculate the energy stored in a fully charged battery if the phone requires charging after 5.00 hours of use.
The human body can exhibit a wide range of resistances to current depending on the path of the current, contact area, and sweatiness of the skin. Suppose the resistance across the chest from the left hand to the right hand is 1.0 106 . (a) How much voltage is required to cause possible heart fibrillation in a man, which corresponds to 500 mA of direct current? (b) Why should rubber-soled shoes and rubber gloves be worn when working around electricity?
The batteries of a submerged non-nuclear submarine supply 1000 A at full speed ahead. How long does it take to move Avogadro’s number (6.02 1023) of electrons at this rate?
(a) A defibrillator sends a 6.00-A current through the chest of a patient by applying a 10,000-V potential as in the figure below. What is the resistance of the path? (b) The defibrillator paddles make contact with the patient through a conducting gel that greatly reduces the path resistance. Discuss the difficulties that would ensue if a larger voltage were used to produce the same current through the patient, but with the path having perhaps 50 times the resistance. (Hint: The current must be about the same, so a higher voltage would imply greater power. Use this equation for power: P=I2 RP = .)
Figure 21.55 shows how a bleeder resistor is used to discharge a capacitor after an electronic device is shut off allowing a person to work on the electronics with less risk of shock, (a) What is the time constant? (b) How long will it take to reduce the voltage on the capacitor to 0.250% (5% of 5%) of its full value once discharge begins? (c) If the capacitor is charged to a voltage V0through a 100-O resistance, calculate the time it takes to rise to 0.865V0(This is about two time constants.)
Imssb1.mutah.edu.jo/mod/quiz/attempt.phpi For the following circuit in the figure below. Determine V-V, (in units of V) for e= 47 V. a 20 Select one CA 783 OB. 940 Oc39.17 D. -940 E-783 8
NCT e-Learnin Portal Courses - Reports e-Services Academic Departments ETC - CIMS 4. The Voltmeter connected across load (Bulb) will measure [Choose any one answer] 5. A constant current source supplies a electric current of 200 mA to a load of 2k2. When the load changed to 500, the load current will be O9mA 0700mA O8A O12A 6. To measure A.C voltage the knob should be at 7.An electrical water heater is rated 3000W. What physical quantity does 3000W represent?