Determine the level of VoSiGeR1VoER2Given :• The Si diode turn on voltage is = 0.65 V• The Ge diode turn on voltage is = 0.35 V• The source voltage E = 12 V• R = 7.5 K• R2 = 3.5 K 2%3Dthen:• The Si diode is Forward Biased :• The Ge diode is Forward Biased +• The Current through R1 =• The output voltage V, =• Power consumed by Si Diode Psi%3DmAVmW

This question belongs to analog electronics . It is based on the concept of analysis of diodes in…

Determine the level of V, Si Ge R1 E R2 Given : • The Si diode turn on voltage is = 0.65 V • The Ge diode turn on voltage is = 0.35 V • The source voltage E = 12 V • R = 7.5 K2 • R2 = 3.5 K then: • The Si diode is Forward Biased : • The Ge diode is Forward Biased • The Current through R1 = mA • The output voltage V, = • Power consumed by Si Diode Psi mW

Determine the level of V, Si Ge R1 E R2 Given : • The Si diode turn on voltage is = 0.65 V • The Ge diode turn on voltage is = 0.35 V • The source voltage E = 12 V • R = 7.5 K2 • R2 = 3.5 K then: • The Si diode is Forward Biased : • The Ge diode is Forward Biased • The Current through R1 = mA • The output voltage V, = • Power consumed by Si Diode Psi mW

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is the difference between a diode and rectifier?
What is CEMF?
Consider the circuit in the figure below 4:1 120 V rms ooooo gll reelee D₁ L a. What type of circuit is this? b. What is the total peak secondary voltage? D₂ c. Find the peak voltage across each half of the secondary. d. Sketch the voltage waveform across RL. e. What is the peak current through each diode? f. What is the PIV for each diode? RL 1.0 ΚΩ
Consider the circuit shown in Figure 2. The cut-in voltage of each diode is . Let and assume both diodes are conducting. Determine if this is a valid assumption and explain your answer. And calculate the values of IR, ID, Ip2, and V.. Rj =1.7 kQ ww VB =1 V D1 Dz R2D 4 kQ Figure 2
Since R1=4.51 Kohm, R2=1.19 Kohm R3=2.74Kohm R4=5.60Kohm VCC=23.00V and diode silicon in the circuit given in the figure, find the current passing through the diode in mA
Q2/ Consider the circuit in below figure. What type of circuit is this? b. What is the total peak secondary voltage? c. Find the peak voltage across each half of the secondary. d. Sketch the voltage waveform across RL. e. What is the peak current through each diode? f. What is the PIV for each diode? а. 4:1 D1 120 V rms RL 1.0 kN 00400
USING D1 1N4001G or SILICON DIODE. To sketch the characteristic curve of the diode you need to vary voltages on diode and measure current flowing during forward and reverse bias condition. Fill up the table below using circuit shown and vary battery voltages. Measure voltage and current of diode then sketch the graph. Voltage X axis and Current Y axis. Battery Diode Diode Voltage Current Voltage Battery Diode voltage Voltage 0.1V 0.3V 0.5V 0.7V 1.0V 2.0V 3.0V 10.0V Diode Current Forward Bias Condition A V 0.1V 0.5V 2.0V 5.0V 10v 20V 25V 30V Reverse Bias Condition Note: used any electronics software to perform this activity
Q1/Consider the circuit in Figure with a transformer of 10:1 transformation ratio and the diodes are silicon. a) What type of circuit is this? (b) What is the total peak secondary voltage? (c) Find the voltage value across the resistor (d) Sketch the voltage waveform across RL (e) What is the PIV for each diode? D3 D 120 V Pisez) Vpouo D D 10 kn lleee
If the positive cycle of the waveform for full wave bridge rectifier , Which of the diodes is working . ..... ...... 10:1 120 V ms Output 60 Hz Puec) RL 220 N Dz 1000µF O D1, D2 D3, D2 D4, D2 D1, D4 not all above D1, D3 ellee
When a conventional Silicon diode is reversed-biased with a voltage high enough such that there is a very large current present, the voltage value this occurs at is referred to as the: a) Breakdown voltage b) Breakup voltage c) Hammer voltage d) Roller voltage O b O d O c a o o o o
What will be the value of the reverse saturation current for a Si diode operating in forward bias mode. The following information is given: Diode current 3 A Voltage across diode 0.25 V. Temperature is 300 K.