Please solve using convolution without the Laplace transform. Consider a discrete time system given byy[n] + ay[n – 1] = x[n] + bx[n – 1] + x[n – 2]If x[n] = cos (n) + cosy[n] = sin (n + 0). Also, what is the resulting phase 0?En), determine the constants a and b so that the output is33

Consider a discrete time system given by y[n] + ay[n – 1] = x[n] + bx[n – 1] + x[n – 2] If x[n] = COS + cos determine the constants a and b so that the output is y[n]: 3 = - sin (n + 0). Also, what is the resulting phase 0? 4

Consider a discrete time system given by y[n] + ay[n – 1] = x[n] + bx[n – 1] + x[n – 2] If x[n] = COS + cos determine the constants a and b so that the output is y[n]: 3 = - sin (n + 0). Also, what is the resulting phase 0? 4

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Discrete Signals and Discrete Time systemsx[n1] = (values) 9 random integer values from -10 to 5x[n2] = (values) 9 random integer values from -5 to 5 a. Plot the graph setting the middle integer value at n = 0 showing the all samples.b. Plot the graph x[-n] showing all the samples.c. Plot the graph x[n-3] showing all the samples.d. Plot the graph x[n+2] showing all the samples.e. Plot the graph x[2n] showing all the samples.f. Plot the graph x[n/3] showing all the samples.g. Evaluate the convolution of x[n1] and x[n2].
A sinusoid signal v(n) = 5 sin( @₂ .n) with f=5 Hz and fs = 10 kHz has to be quantized @ (Vq(n) = Q[v(n)]) with a midtreat quantizer. The range of the signal is ±5 V and the word length of the quantizer 4 bits. The quantizer is at digital full scale. (a) How many quantization levels L does the quantizer have? What is the value of A? (b) Sketch the input-output characteristic of the quantizer. How different is a midtreat quantizer to a midrise quantizer. (c) For time index n = 1250 calculate the quantized value v₁ (n), the quantization error eq(n) and represent vą (n) using RZ code. (d) Calculate the power P of the quantization noise. (e) Determine the SNR in dB.
n Which of the following statements is not correct: O a. A first-order PLL can track a phase step with a zero steady-state error. O b. A first-order PLL can track a frequency step with a zero steady-state error. Oc. A second-order PLL can track a frequency step with zero steady-state error. O d. A third-order PLL can track a frequency step with zero steady-state error.
For the continuous time signal x [n] shown below, draw each signal in the options and state the x and y values in the figure.(a) x [3 - n](b) x [3n + 1](c) x [n] u [3 - n](d) x [n-2] ? [n - 2](e) x [(n-1)2]
1. Consider a sinusoidal signal x(t)=sin(2n50t) for ten complete cycles. Using this signal, plot to represent the following: (a) Plot x(t) as analog continuous signal (b) Plot x(t) as analog discrete-time signal (c) Quantize the signal to 4 levels, +1, +1/3, -1/3, -1 and plot the corresponding i) digital discrete-time signal; and ii) digital continuous signal (d) Plot the amplitude spectrum for the sinusoidal signal generated in part (a). (e) Plot the phase spectrum for the sinusoidal signal generated in part (a).
2. The signal x(t) = sin(2022nt) is sampled at 455 Hz. Deternmine the equivalent signal and sampled signal expression.
2) A voltage signal consists of the following periodical waveform: V(t) = 10 sin 502.7t + 5 sin 94.2t + 15 sin 942.5t where t is in seconds and Vin volts. This signal is sampled digitally at a sampling frequency of 200 Hz. 128 data points are taken. a) Recommend additional procedures to sample the signal properly in the frequency domain considering the sampling conditions given above. b) Sketch what the frequency spectrum would look like if you were to perform an FFT on these sampled data. Label your axes carefully. c) Calculate: - the total sampling time - the time increment between sampled data points - the frequency resolution of the frequency spectrum - the Nyquist frequency
ス45 Rb M[Q4] The signal r(t) = 2 sin(200rt) is sampled at a rate of 800 samples per second. Draw 1.5 cycles of the analog signal and show where sampling occurs on the waveform. M[Q5] The signal r(t) = 100 sin(200rt) +75 cos(300rt) is sampled every 20 ms. (a) Is the sampling adequate? If not, what would be the adequate sampling rate? (b) plot the spectrum of the sampled signal, %3D
Generate a single-tone signal whose peak amplitude is 2 V and frequency of 1000 Hz. Use a 20000 Hz sampling rate and a duration of 1 s. Plot the signal for the first 50 points only and observe (listen to) the signal using the wavplay (Note: DO NOT DO THE wavplay COMMAND! It is going to get very noisy in the laboratory. But do include the command in your code.) MATLAB code:
A sinusoid has a period T0 = 3 dt, an amplitude of 1.5 mVolt, and an phase = 15 degrees a. Write down the representation of this signal.b. Perform the sampling process on the above signal with a sampling frequency of Fs = 2 kHz. Write an expression for the sampled sinusoid signal and determine the digital frequency.
Consider the following sampled signal x[n]. What is the cyclic frequency in the sampled signal if the signal was sampled with a sampling frequency of 40 Hz? x[n] = 1 + 2cos((pi/4)n +(pi/3))
A) Give the graphical representation and the relationship form of 1) r(-5+n) 2) p(n- 3) u(n).r(-5+n). p(n-3) B) Write the signal in form U(n) by using the basic operation